Avaya S8500 Series Bedienungsanleitung
555-245-760 Issue 3 January 2005 1
Replacing the S8500 dual network interface
This section describes the steps required to replace an existing dual network interface card
(NIC) on the S8500 and S8500B Media Servers. The control network traffic from the server out
to the dedicated customer LAN travels through the NIC.
Note:
Note: This procedure applies to both S8500B and S8500 media servers. The section
about Installing the new network interface cardhas different procedures for
S8500B and S8500.
The components of this procedure include:
●Backing up the media server
●Powering down the media server
●Removing the cover of the media server
●Removing the fan unit
●Removing the old network interface card
●Installing the new network interface card
●Replacing the fan unit
●Replacing the cover and cabling
●Powering up the server
●Checking LED activity on the dual network interface card
●Confirming original Ethernet configuration
!CAUTION:
CAUTION: Wear an antistatic wrist ground strap whenever handling the media server or its
components. Connect the strap to an approved ground, such as an unpainted
metal surface.
Backing up the media server
Backup the media server before you power it down. To backup the media server complete the
following steps:
1. Connect the services laptop to the port labeled 2 (Eth 1) on the back of the media server
using the crossover cable.
2. Open a browser window on the laptop.
Replacing the S8500 dual network interface
2 Replacing the S8500 dual network interface
3. In the address field of the browser, type in the URL for the media server and press Enter.
A welcome window opens (Figure 1: Welcome Window on page 2).
Figure 1: Welcome Window
4. Click Continue.
5. Accept the Avaya certificate by clicking Yes.
The logon window appears (Figure 2: Logon window on page 3).
555-245-760 Issue 3 January 2005 3
Figure 2: Logon window
6. Type craft in the Logon ID field and the password (obtained from ART) in the Password
field and click Logon.
7. Suppress alarm origination by clicking Yes.
8. Click Launch Maintenance Web Interface.
9. Select Data Backup/Restore > Backup Now from the navigation pane.
10. Select All data sets under the Data Sets heading.
11. Select one of the following backup methods:
●FTP
●E-mail
●Local PC card
12. If you want to encrypt the backup, select the Encrypt backup using pass phrase check
box and type a pass phrase.
13. Click Start Backup.
Replacing the S8500 dual network interface
4 Replacing the S8500 dual network interface
Powering down the media server
After the backup is finished, complete the following steps to power down the media server.
1. From the media server Web interface click Shutdown This Server.
2. Select Delayed.
3. After the media server shuts down unplug the power cord from the back of the server.
4. Unplug the power cord from the RSA.
5. Disconnect the modem from the RS-232 port on the RSA.
6. Disconnect and label the LAN connection (if used) from the Ethernet port on the RSA.
7. Pull the server forward so that the server rails expand and the retaining clips on the rails
click into place.
8. Unplug and label the cable from the Ethernet port labeled LINK A on the dual NIC.
Removing the cover of the media server
!CAUTION:
CAUTION: Remove all power from the media server before starting this procedure.
To remove the cover of the media server:
1. Loosen the two captive screws on the back of the media server (see Figure 3: Locating the
server cover’s captive screws on page 5.
2. Slide the server cover back from the front panel until the cover’s tabs are released from the
top slot of the front panel.
3. Lift the cover straight up and move it away from the server as shown in Figure 3: Locating
the server cover’s captive screws on page 5.
555-245-760 Issue 3 January 2005 5
Figure 3: Locating the server cover’s captive screws
Removing the fan unit
To remove the fan unit from the media server:
1. Locate the slot labeled PCI-2 on the left hand side of the back of the server under the fan
unit.
2. Remove the two screws holding the fan unit. You do not need to unplug the fan unit.
3. Set the adapter-support bracket to the right of the fan.
Figure notes:
1. Server cover’s captive screws
h3mscaps LAO 070103
disc
1
Replacing the S8500 dual network interface
6 Replacing the S8500 dual network interface
Removing the old network interface card
To remove the old NIC:
1. Completely unscrew the captive screw on the left hand side of the PCI-2 slot.
The captive screw is now loose so that you can flip it up. You will need this space to
maneuver the old NIC out of its slot.
2. Firmly pull the card out of its slot.
Installing the new network interface card
Depending on the S8500 server model, use one of the following procedures:
●Installing the new network interface card in the S8500B media server
●Installing the new network interface card in the S8500 Media Server
Installing the new network interface card in the S8500B media server
Note:
Note: The procedure is for S8500B.
Note:
Note: Wear an antistatic wrist ground strap whenever handling the media server or its
components. Connect the strap to an approved ground, such as an unpainted
metal surface. See the job aid titled Approved Grounds for more information.
To install the network interface card (NIC):
1. Carefully grasp the new NIC by the top edge or upper corners and align it with the PCI-2
expansion slot on the motherboard. (The SAMP is connected on the other side of this
connector.) Press the NIC firmly into the expansion slot. See Figure 4: Inserting the
network interface card on page 7.
555-245-760 Issue 3 January 2005 7
Figure 4: Inserting the network interface card
!CAUTION:
CAUTION: Be sure that the NIC is completely and correctly seated in the PCI-2 expansion
slot of the Avaya S8500B Media Server. Incomplete insertion might cause
damage to the system board or the NIC.
2. Position the faceplate so that it fits in the PCI-2 slot using the captive screw to hold it in
place.
3. Tighten the captive screw.
Installing the new network interface card in the S8500 Media Server
Note:
Note: This procedure is for S8500.
To install the new NIC into the S8500 media server:
1. Carefully grasp the new NIC by the top edge or upper corners and align it with the PCI-2
expansion slot (see Figure 5: Inserting the new network interface card on page 8). Press
the NIC firmly into the expansion slot.
Ensure that the NIC is completely and correctly seated in the PCI-2 expansion slot of the
S8500 Media Server. Incomplete insertion might cause damage to the system board or the
NIC.
2. Position the faceplate so that it fits in the PCI-2 slot using the captive screw to hold it in
place.
2
1
indsbnic KLC 101404
Replacing the S8500 dual network interface
8 Replacing the S8500 dual network interface
Figure 5: Inserting the new network interface card
Replacing the fan unit
To replace the fan unit in the media server:
1. Replace the fan unit with the fan blades pointed down toward the NIC, securing the fan unit
with the two original screws.
Figure notes:
1. Mounting screws 3. Network interface card
2. Fan assembly 4. Smaller faceplate
PCI
1
PCI 2
100-127-,3,0A,50/60Hz
200-240-,1,5A,50/60Hz
133MHz/64Bit, 100MHz/64Bit
h3ms2nic KLC 031004
1
2
4
5
3
555-245-760 Issue 3 January 2005 9
Replacing the cover and cabling
To replace the cover and cabling on the media server:
1. Replace the cover onto the server.
2. Slide the cover forward so the cover’s tabs slide into place under the top slots of the front
panel.
3. Finger-tighten the thumb screws on the back of the server.
4. Release the retaining tabs on the rails and slide the S8500 Media Server back into place on
the data rack.
5. Locate the marked cable that you removed from the old NIC and plug it into the Ethernet 2
port, which is labeled “ACT/LINK A” on the small faceplate of the new NIC.
6. Connect all external cables.
Powering up the server
To power up the media server:
1. Plug the power cord into the power receptacle on back of the server.
2. Press the Power button located on the front right-hand side.
3. Log in to the server after the startup to ensure that the installation is complete.
Checking LED activity on the dual network interface card
When the media server is back in service, check the LEDs on each port of the dual NIC
(Figure 6: S8500 rear panel dual NIC LEDs on page 10).
Replacing the S8500 dual network interface
10 Replacing the S8500 dual network interface
Figure 6: S8500 rear panel dual NIC LEDs
Confirming original Ethernet configuration
After the media server is back in service, check the original Ethernet configuration settings:
1. Go to Server Configuration > Configure Server Web page.
2. Confirm that the server’s Ethernet configuration settings are the same as before.
Configuring the NIC
To configure the new NIC:
1. At the Web interface select Server Configuration > Configure Server.
2. Click Continue through the review notices until you get to the xxx page.
3. Select Configure Individual Services and click Continue.
4. Select Set Identities and click Continue.
5. The following Ethernet ports are listed:
●Control Network A: [default: Ethernet 0]
●Services Port: [default: Ethernet 1]
●Corporate LAN: [default: Ethernet 0]
Figure notes:
1. Network activity LED
(Tx/Rx)
2. Connection rate:
●LED is off: there is a 10 BASE-T active link.
●LED is green: there is a 100 BASE-T active link.
●LED is orange: there is a 1000 BASE-T active link.
1 2
LINK TX/RX LINK TX/RX
PCI
1
PCI 2
100-127 -, 3,0A, 50/60 Hz
200-240 -, 1,5A, 50/60 Hz
133 MHz/64 Bit, 100 MHz/64 Bit
h3msble2 KLC 082503
100-127 -, 3,0A,
200-240 -, 1,5A, 5
1
2
Andere Handbücher für S8500 Series
20
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Avaya Server Handbücher
Avaya
Avaya CS700 Bedienungsanleitung
Avaya
Avaya Polycom SpectraLink 8400 Series s Bedienungsanleitung
Avaya
Avaya S8300 Series Handbuch
Avaya
Avaya P133F2 Bedienungsanleitung
Avaya
Avaya S8700 Series Bedienungsanleitung
Avaya
Avaya S8400 Bedienungsanleitung
Avaya
Avaya Virtual Services Platform 9010 Bedienungsanleitung
Avaya
Avaya Aura S8800 Bedienungsanleitung
Avaya
Avaya S8500 Series Bedienungsanleitung
Avaya
Avaya Scopia Bedienungsanleitung
Avaya
Avaya Aura System Platform Bedienungsanleitung
Avaya
Avaya S8500 Series Montageanleitung
Avaya
Avaya S8700 Series Bedienungsanleitung
Avaya
Avaya 1000E Beilage
Avaya
Avaya INTUITY AUDIX LX Bedienungsanleitung
Avaya
Avaya DEFINITY Server R Bedienungsanleitung
Avaya
Avaya S8400 Bedienungsanleitung
Avaya
Avaya 1000 Series Bedienungsanleitung
Avaya
Avaya Definity Enterprise Communications Server Bedienungsanleitung
Avaya
Avaya QuesCom 400 Leitfaden
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung