AWS ES-250 Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere AWS Skala Handbücher

Beliebte Skala Handbücher anderer Marken

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung

American Weigh Scales, Inc.

ES-250

ES-400

User Manual

ES-Series

Digital Pocket Scale

ES Series Manual

Thank you for purchasing the American Weigh

ES Series digital scale. Please read all operating

instructions carefully before use. This electronic scale

is a precision instrument. With normal care and proper

treatment, it will provide years of reliable service.

Never load the scale with more than the maximum

capacity. Overloading will permanently damage it!

Avoid any exposure to extreme heat or cold. Your

scale works better when operated at normal room

temperature. Always allow the scale to acclimate to

normal room temperature for at least one hour before

use.

Give your scale sufcient warm up time. Usually

30-60 seconds before calibration to give the internal

components a chance to stabilize.

Keep your scale in a clean environment. Dust, dirt,

moisture, vibration, air currents and a close distance to

other electronic equipment can all cause an adverse

effect on the reliability and accuracy of your scale.

Handle with care. Gently apply all items to be weighed

onto tray top. Although this scale is designed to be

quite durable, try to avoid rough treatment as this may

permanently damage the internal sensor.

Avoid shaking, dropping or otherwise shocking the

scale. This is a precision instrument and must be

handled with extreme care.

Only operate the scale on a stable, vibration free

surface.

I. OPERATION

1. Press [I/O] key.

2. Wait until “0.0” is displayed.

3. Put the object(s) on the weighing platform.

4. Using the [M] key, you can switch between the

weighing units.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place the “tare item” on the platform.

3. Press [T] and wait until “0.0” is displayed.

4. Add the “net-weight-item”.

III. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if scale is not weighing properly.

**Make sure you use the correct calibration weight for

your scale or the calibration will not be accurate**

1. Turn OFF the scale.

2. Press [I/O] shortly. Then immediately press and hold

[M] until “CAL” is displayed. Release the [M] key.

3. Press [M] again. Now the display reads “CAL” and

then “200g” will ash 3 times.

4. Place your 200g calibration weight on the center of

platform. Wait 3-4 seconds. The LCD display reads

“PASS”.

5. Remove the weight and press [I/O] to turn off the

scale. Finished! Repeat if needed.

Please check the availability of weights with your scale

supplier.

IV. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display] Elimination of errors

Nothing, Battery-Symbol, [lo] or [88888]

Change the batteries.

[OUE2] Recalibrate the scale as shown above.

[EEEEE] You are overloading the scale. Remove the

excessive load immediately!

[LLLLL] The delicate weighing load cells have

been damaged by misusing the scale

(i.e. it was shocked, dropped or

overloaded). You can try recalibrating the

scale. If the load cell has not been

damaged too much it will work

again after recalibration.

[UNST] Use the scale in a more stable position

Specications

Model ES-250 ES-400

Capacity 250g

8.82oz

8.54ozt

160.75dwt

400g

14.11oz

12.86ozt

257.21dwt

Resolution 0.1g / 0.01oz / 0.01ozt / 0.1dwt

Display 4.5 - Digit Backlit LCD

Calibration Weight

(not Included) 200g 200g

Platform Dimensions

(inches) 2.6 x 1.75

Scale Dimensions

(inches) 3.875 x 3 x 0.5

Power 2 x CR2032 Batteries (included)

Gross Weight 0.28 lb