B-K lighting ArtiStar Remote Bedienungsanleitung

NEEDED

FOR

INSTALLATION:

9/64” Allen Wrench

Waterproof Wire Connector

Warning Flammable Hot Surface

PVC Housing

UL-AR

Stability Flange

Body

Faceplate

18 Ga. Wire

Flush Mount

Collar

Low Voltage

ARTISTAR UPLIGHT

Flush Mount

Standard Installation

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local and

Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause an

unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as

this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type of

power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning on.

Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

Proper soil preparation is recommended before installation. See the DIG-IT guide at

www.bklighting.com/collaterals/install/digit.pdf for more information.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

RELEASE DATE

12/15/2021

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

REFERENCE NUMBER

INS-2317-00

Please refer to the low

voltage design guide at www.

bklighting.com/lvguide before

installation for proper wire

selection.

Finished grade

12”

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Screws on faceplate will

align with alignment

arrows on temporary

cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade

Concrete

Wire nuts must

clear opening

6”

min.

Finished grade

15”

5. Align holes to final installation orientation.

Arrows on temporary cover point towards

screw location on faceplate for alignment

purposes.

NOTE: Do not remove temporary cover until

installation of faceplate.

Finished grade

12”

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Screws on faceplate will

align with alignment

arrows on temporary

cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade

Concrete

Wire nuts must

clear opening

6”

min.

Finished grade

15”

1. Excavate trench according to designed

lighting plan 12” deep and 12” wide suitable

for the fixture housing.

2. Supply low voltage wiring necessary for

installation.

3. Slide stability flange onto housing.

NOTE: Product is supplied with a

stability flange to anchor fixture and aid in

installation.

4. Loop minimum of 6” of low voltage wire inside

housing to allow for fixture service. Place

fixture in hole.

NOTE: Do not remove temporary cover!

Fixture Installation

6. Per DIG-IT Guide, backfill the gap between

the bottom of housing and bottom of hole with

sand or pea gravel for drainage.

NOTE: The mounting collar must be flush to

finished grade. Use stability flange to aid in

installation as shown.

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

7. Fill the hole around the fixture housing to 12”

below the finished grade with clean fill dirt and

tamp carefully to prevent settling of fixture.

Pour concrete and finish as required flush with

mounting collar.

RELEASE DATE

12/15/2021

REFERENCE NUMBER

INS-2317-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

ARTISTAR UPLIGHT

Flush Mount

Standard Installation

Soil Prep

Conduit

trench

B. Dig hole 10” wide and 10” deep.

Conduit

Trench

Excavated

for Housing

C. Prep soil according to DIG-IT Guide.A. Determine Soil Type by referencing DIG-IT

Guide. Prep soil according to DIG-IT Guide.

Finished grade

Concrete

Wire nuts must

clear opening

6”

min.

9. Access low voltage wire inside power pipe. Make

two water tight, low voltage connections using

proper wire connectors. Wire nuts must clear

opening. Insert fixture and low voltage wire into

housing. See wiring diagram.

10. Mount faceplate to collar using two (2) #8-32

flat head screws (included) with a 9/64” allen

wrench.

WIRING DIAGRAM

LED - For use with 12VAC LED remote

transformer or magnetic transformers only.

B-K Lighting cannot guarantee performance

with third party manufacturers’ transformers.

8. Remove temporary cover and pull out low

voltage wire.

RELEASE DATE

12/15/2021

REFERENCE NUMBER

INS-2317-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

ARTISTAR UPLIGHT

Flush Mount

Standard Installation

HOT 12V

12V

FIXTURE

NEUTRAL

Remote

Transformer

1. Remove faceplate from collar using two (2) #8-32

flat head screws (included) with a 9/64” allen

wrench.

Fixture Relamping

2. Remove fixture from collar. 3. Loosen two (2) #8-32 screw with a 5/64” allen

wrench to remove faceplate.

4. Space three fingers evenly around the optic and

gently rock optic to remove.

6. Disengage LED board and driver assembly.

Replace with new board and driver assembly.

7. Reverse install LED board and driver by carefully

engaging quick disconnects and inserting into

fixture body. Secure LED board in place with

stainless steel screws. Snap optics in place.

8. With flat head screw driver rotate dial to desired

lumen output. Replace fixture in mounting collar.

5. Use a 5/64” allen wrench to remove two (2) #2-56

socket head cap screws on LED board, grasp

LED board and gently pull up to expose quick

disconnect.

9. Mount faceplate to collar using two (2) #8-32 flat

head screws (included) with a 9/64” allen wrench.

Do not overtighten.

RELEASE DATE

12/15/2021

REFERENCE NUMBER

INS-2317-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

ARTISTAR UPLIGHT

Flush Mount

Standard Installation

Andere B-K lighting Beleuchtungsausrüstung Handbücher

B-K lighting

B-K lighting YOSEMITE Series Bedienungsanleitung

B-K lighting

B-K lighting SS Bedienungsanleitung

B-K lighting

B-K lighting LT Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting MB2 Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Series Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO DRIVESTAR Bedienungsanleitung

B-K lighting

B-K lighting SIGN STAR Series Bedienungsanleitung

B-K lighting

B-K lighting PS Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting Denali Series Bedienungsanleitung

B-K lighting

B-K lighting Mini-Micro Series Bedienungsanleitung

B-K lighting

B-K lighting BACK BOX Bedienungsanleitung

B-K lighting

B-K lighting MICRO NITE STAR Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting Path Star Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting DENALI Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Bedienungsanleitung

B-K lighting

B-K lighting INTEGRAL DENALI Series Bedienungsanleitung

B-K lighting

B-K lighting RE1 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung