B-K lighting RE1 Bedienungsanleitung

TOOLS

NEEDED:

3/32”, 1/8” & 7/64” Allen Wrench

Waterproof Wire Connectors

Epoxy (Supplied)

Sleeve or Wedge Anchors for Concrete (1/4” Dia. Min.)

Data Cable (RE3 Option Only)

Receptacle Bollard

Warning High Voltage

Installation Instructions

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

CONCRETE INSTALLATION ONLY

RE1 Option - GFI

PVC (Optional)

Primary 3/4”

Conduit

Connectors

Machined

Aluminum

Housing

(2) 3/4” x 3/4”

Opening for Cord

Sets

Machined Base

Receptacle

(Option Varies)

Grade Label

Epoxy

RE2 Option - GFI & USB

RE3 Option - RJ45 Jack

Cover with

Captive Tamper

Resistant Screw

Tenon

Steel Plate

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning

on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

RELEASE DATE

12/21/2021

REFERENCE NUMBER

INS-2701-00

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all

Local and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping

of this product.

• Before wiring to power supply and during servicing or

relamping, turn off power at fuse or circuit breaker before

service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause

an unsafe condition. The use of damaged components may

cause an unsafe condition and void product warranty.

• Do not block light emanating from product in whole or

part, as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time.

Use a clean, dry, soft cloth to handle the lamp. Oil from

skin may damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept

clean during installation and service; failure to do this may

cause an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

Proper soil preparation is recommended before installation. See the DIG-IT guide at bklighting.com/collaterals/install/digit.pdf

for more information.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

RELEASE DATE

12/21/2021

REFERENCE NUMBER

INS-2701-00

2. Connect conduit to the 3/4” primary conduit

couplers attached to the bottom of the PVC

housing. Place PVC housing in hole.

3. Prep for concrete. Base is flush with finished

grade.

4. Pull branch circuit wiring necessary for

appropriate installation.

1. Excavate trench according to designed lighting

plan. Dig hole a minimum of 24” deep and

10” wide to accommodate PVC housing at

desired fixture location and direction of in-use

receptacle(s).

Finished grade

Pea Gravel

or Sand

Concrete

Finished Grade

GRADE

Finished gradePea Gravel

or Sand

Concrete

Finished Grade

GRADE

Finished grade

Pea Gravel

or Sand

Concrete

Finished Grade

GRADE

PVC HOUSING MUST BE INSTALLED AS PER GRADE LABEL. HOUSING IS LABELED AT GRADE

LEVEL. HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY

Align holes

for screw

orientation

3. Prepare epoxy (included) according to

instructions on packaging.

INSTALLATION OF BASE

6. Place base onto epoxyed PVC housing over

steel plate, lining up with steel plate mounting

holes and drilled mounting holes in concrete.

4. Use mixing stick to apply the epoxy to the

exterior of exposed PVC housing as shown, in

smooth, continuous application.

1. Steel plate and base has four (4) 5/16” dia. holes

at 3” square on center for mounting hardware.

Use steel plate as template for final mounting

drill hole positions.

2. Drill four (4) holes into concrete for minimum 1/4”

sleeve or wedge anchors for concrete. Clean or

vacuum debris from drilled holes.

Minimum of 1/4” dia. anchors must be used.

5. Place steel plate epoxyed PVC housing, lining

up with drilled mounting holes in concrete.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Receptacle Bollard

Installation Instructions

INSTALLATION OF PVC MOUNTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

RELEASE DATE

12/21/2021

REFERENCE NUMBER

INS-2701-00

LINE

COM

GROUND GROUND

BASE

In-Use

Receptacle

DATA In-Use

Receptacle

RJ45

WIRING DIAGRAM

1. Pull branch circuit wiring. Make watertight

connections from primary branch circuit

to in-use receptacle using waterproof wire

connectors. Connect incoming ground and

ground from receptacle to ground wire on

base. See wiring diagram.

INSTALLATION OF IN-USE RECEPTACLE (RE1 & RE2 Option)

2. Attach ground from branch circuit to screw

on anchor base. Place connectors inside

receptacle.

3. Attach in-use receptacle to installed anchor

base with four (4) #10-32 button head stainless

steel cap screws at the base using a 1/8” allen

wrench.

4. Receptacle cover has captive #6-32 screw.

Secure receptacle by tightening captive #6-32

set screw using a 7/64” allen wrench.

Receptacle cover has two (2) openings for

in-use cord sets.

7. Mount base and plate to concrete using

mounting holes drilled previously (Mounting

Hardware by Others). Minimum 1/4” diameter

sleeve or wedge anchors for concrete must be

used.

9. Seal base and plate as per NEC. Continue with

installation of In-Use Receptacle option chosen.

8. Tighten four (4) #10-32 screws in base using a

3/32” allen wrench to secure to installed PVC

housing.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Receptacle Bollard

Installation Instructions

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

RELEASE DATE

12/21/2021

REFERENCE NUMBER

INS-2701-00

LINE

COM

GROUND GROUND

BASE

In-Use

Receptacle

DATA In-Use

Receptacle

RJ45

WIRING DIAGRAM 5. Place connection(s) and/or cable inside

receptacle.

6. Attach in-use receptacle to installed anchor

base and plate with four (4) #10-32 button

head stainless steel cap screws at the base

using a 1/8” allen wrench.

7. Receptacle cover has captive #6-32 screw.

Secure receptacle by tightening captive #6-32

set screw using a 7/64” allen wrench.

Receptacle cover has two (2) openings for

in-use cord sets.

4. Place connections into bollard. Attach inner

bracket with RJ45 jack with two (2) #6-32

screws with a 7/64” allen wrench.

INSTALLATION OF IN-USE RECEPTACLE (RE3 Option)

2. Loosen two (2) #6-32 screws with a 7/64”

allen wrench to remove inner bracket with

RJ45 jack.

3. Connect incoming data cable to RJ45 jack as

per installation plan. Follow manufacturer’s

instructions as per cable and method of

connection to RJ45 jack (cable and connections

required By Others). See wiring diagram.

1. Open receptacle cover. Receptacle cover has

captive #6-32 screw for use with a 7/64” allen

wrench.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Receptacle Bollard

Installation Instructions

Dieses Handbuch passt für folgende Modelle

Andere B-K lighting Beleuchtungsausrüstung Handbücher

B-K lighting

B-K lighting Mini-Micro Series Bedienungsanleitung

B-K lighting

B-K lighting BACK BOX Bedienungsanleitung

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Bedienungsanleitung

B-K lighting

B-K lighting INTEGRAL DENALI Series Bedienungsanleitung

B-K lighting

B-K lighting CORE DRILL Bedienungsanleitung

B-K lighting

B-K lighting HP2RM Bedienungsanleitung

B-K lighting

B-K lighting Path Star Bedienungsanleitung

B-K lighting

B-K lighting MICRO NITE STAR Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting Nite Star Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting SS Bedienungsanleitung

B-K lighting

B-K lighting LT Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Integral Bedienungsanleitung

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Bedienungsanleitung

B-K lighting

B-K lighting PS Bedienungsanleitung

B-K lighting

B-K lighting DENALI Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO RECESSED UPLIGHT Bedienungsanleitung

B-K lighting

B-K lighting TETON Bedienungsanleitung

B-K lighting

B-K lighting SIGN STAR Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung