B-K lighting Precision2 HP2 Series Bedienungsanleitung

RELEASE DATE

12-11-16

REFERENCE NUMBER

INS001399

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

Warning High Voltage Hot Surface

Waterproof Wire

Nuts

Silicone ‘O’ Ring

OptiLock®

Patented

Stability

Flange

1/8” Allen Wrench

Phillips screwdriver

Level

NEEDED

FOR

INSTALLATION:

By Others

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

Quick

Disconnects

Patented

HydroLock®

Plate

Driver Tray

HP2 Housing

Optic

HP2SERIES

Solid State LED with Color Tuning

HP2 Faceplate

Installation Instructions

Soil Prep

Conduit

trench 18”

Dia.

A. Determine Soil Type by referencing

DIG-IT Guide.

B. Dig hole 18” wide and 20” deep.

Conduit

Trench

Excavated

for Housing

C. Prep soil according to DIG-IT Guide.

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of

this product.

• Before wiring to power supply and during servicing or relamping,

turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause

an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time. Use

a clean, dry, soft cloth to handle the lamp. Oil from skin may

damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted lamp is HOT!

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

turning on.

Do not touch hot lens, guard, or enclosure (see diagram/

picture).

Keep lamp away from materials that may burn.

Do no touch the lamp at any time. Use a soft cloth. Oil

from skin may damage lamp.

Do not operate the luminaire fitting with a missing or

damaged shield.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations · Suitable for recessed in ground locations

IMPORTANT LISTINGS AND CERTIFICATIONS

Module

RELEASE DATE

12-11-16

REFERENCE NUMBER

INS001399

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

2. Place housing in hole. Align junction box in the

path of the conduit trench.

3. Insert (4) pieces of ½” EMT conduit through the

Stability Flange™. Hammer into substrate until

secure.

Leave sufficient clearance to elevate housing

to finished grade.

4. Raise housing on EMT so concrete pour collar is

flush with finished grade. Use a level to aid in

housing installation.

5. When housing is level, tighten screws on

Stability Flange™ to secure housing to EMT.

Remove excess EMT as needed.

8. Per DIG-IT Guide, backfill the gap between the

bottom of housing and bottom of hole with

sand for drainage.

Housing Installation

Threaded Entry

Side Flats

1. Connect branch conduit connectors (By Others)

to the junction box using either the threaded

conduit entries on the bottom of the junction

box or through holes drilled into the sides of the

junction box.

Flush with finished grade

6. Connect the conduit to the conduit connectors.

7. Pull primary branch circuit wiring into junction

box.

9. For soil installation: Fill and tamp soil to

the appropriate height leaving room for sod,

pavers, etc. to be level with the top of the

temporary cover.

Soil installation is not drive-over rated.

10. For concrete installation: Fill the hole around

the fixture housing to 12” below the finished

grade with clean fill dirt and tamp carefully to

prevent settling of fixture. Pour concrete and

finish as required flush with the top surface of

the temporary cover.

HP2SERIES

Solid State LED with Color Tuning

Installation Instructions

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

RELEASE DATE

12-11-16

REFERENCE NUMBER

INS001399

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

8. Attach optical assembly to installed driver

assembly with quick disconnect.

3. Wipe inside of housing where HydroLock® plate

will sit clean of debris before inserting patented

HydroLock® plate on to junction box. Align

HydroLock® plate with pins in housing and seat

it firmly in place.

Installation

5. Connect driver assembly to Patented Hydro-

Lock™ Barrier Plate with quick disconnects.

1. Remove temporary cover. 2. Make watertight connections using waterproof

wire connectors (provided) to leads on the

bottom of Patented HydroLock® Barrier Plate

Assembly. See wiring diagram.

4. Turn HydroLock®

Barrier Plate clockwise ¼” to

lock.

Patented HydroLock® Barrier Plate must be

completely seated to ensure proper seal or

water may intrude. This step must be done

as stated or you will void your warranty.

HP2SERIES

Solid State LED with Color Tuning

Installation Instructions

6. Attach driver assembly to housing by aligning

keyhole notch under one (1) of three (3) #8 screw

heads.

7. Tighten the Phillips screws to secure driver

plate to housing.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

WIRING DIAGRAM - HydroLock® Plate

8 wire, 2 plug HydroLock® plate. Connect incoming

primary, ground and chosen external 0-10V and CCT

controls to HydroLock® plate. Use LCT to control

CCT, Dimming, Saturation, and Hue.

hybrid (0-10v wired dimming & continuous cct /sat. and hue by LCT)

LINE

MODULE

COM

GROUND

Driver

10V

0V 0-10V Dim -

0-10V Dim +

Red

Black

0-10V CCT -

0-10V CCT +

LCT

Dimming

Continuous

CCT

10V

LINE

MODULE

COM

Driver

Red

Black

LCT

wireless (0-10v dimming, continuous cct, sat. and hue by LCT)

LINE

MODULE

COM

GROUND

Driver

10V

0V DIM 0-10V -

DIM 0-10V +

Red

Black

LCT

Dimming

hybrid (0-10v dimming wired, /continuous cct, sat. and hue by LCT)

Hydrolock

Plate

LINE

COM

GROUND

10V

LCT

hp2/co2

wired (0-10v wired dimming & continuous cct /sat. and hue by LCT)

LINE

MODULE

COM

GROUND

Driver

10V

Red

Black

Dimming

Continuous

CCT

10V

0-10V Dim -

0-10V Dim +

0-10V CCT +

0-10V CCT -

0-10V Dim -

0-10V Dim +

0-10V CCT -

0-10V CCT +

LCT (Light Commissioning Tool) must be

within 10 meters range of fixture for wireless

operation.

RELEASE DATE

12-11-16

REFERENCE NUMBER

INS001399

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

HP2SERIES

Solid State LED with Color Tuning

Installation Instructions

9. For Optional Accessory Holder: Gently press

accessory holder downwards over optic on

OptiLock® .

10.

Aim fixture by adjusting OptiLock® assembly

with Phillips screw driver.

11. Remove any dirt or debris in O-ring groove near

top of housing. Place O-Ring inside of groove.

Failure to clean groove of debris will cause

fixture to fail and void product warranty.

12. Install faceplate using 1/8” Allen wrench and

hand-tighten the faceplate screws in a star

pattern to 30 in-lbs. min.

Do not use a power tool to install screws. Do

not exceed 40 in-lbs.

RELEASED

4-18-16

REFERENCE NUMBER

INS-2321-14

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

LED MODULE / OPTICS

HP2 - Color Tuning

Module Replacement

Warning Hot Surface

TOOLS

NEEDED:

By Others

1/8”, 5/32” & .050” Allen Wrench

3. Loosen, then remove three (3) #2-28 screws from

optic module using .050” Allen wrench. Remove

optic holder from module.

5. Carefully remove LED module from heatsink, then

disconnect the quick disconnects for the wiring

and the control wiring from the fixture to the LED

module.

Do not pull on connectors or wiring. Handle with

care.

4. Loosen and remove two (2) #2-56 screws holding

LED module to heatsink.

7. Secure LED module to heatsink with two (2) #2-56

screws.

6. Connect new LED module to fixture via quick

disconnects for wiring and for control wiring. Place

new LED module onto heatsink, lining up module

with holes for screws.

Replacing LED Module and Optic

1. Remove faceplate using 1/8” Allen wrench and

loosen the faceplate screws in a star pattern to 30

in-lbs. min.

2. Gently twist optic to the left so optic tabs are clear

of optic holder and carefully pull away.

8. Line up optic tabs in the optic holder, then gently

twist to the right.

9. Remove any dirt or debris in O-ring groove near top

of housing. Place O-Ring inside of groove.

Failure to clean groove of debris will cause fixture

to fail and void product warranty.

10. Install faceplate using 1/8” Allen wrench and hand-

tighten the faceplate screws in a star pattern to 30

in-lbs. min.

Do not use a power tool to install screws. Do not

exceed 40 in-lbs.

Andere Handbücher für Precision2 HP2 Series

Inhaltsverzeichnis

Andere B-K lighting Beleuchtungsausrüstung Handbücher

B-K lighting

B-K lighting Nite Star Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO DRIVESTAR Bedienungsanleitung

B-K lighting

B-K lighting DENALI Bedienungsanleitung

B-K lighting

B-K lighting HP2RM Bedienungsanleitung

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Bedienungsanleitung

B-K lighting

B-K lighting TETON Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO RECESSED UPLIGHT Bedienungsanleitung

B-K lighting

B-K lighting Path Star Bedienungsanleitung

B-K lighting

B-K lighting Precision2 HP2 Series Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting PRECISION2 CO2 Series Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Series Bedienungsanleitung

B-K lighting

B-K lighting MB2 Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Bedienungsanleitung

B-K lighting

B-K lighting Denali Series Bedienungsanleitung

B-K lighting

B-K lighting SIGN STAR Series Bedienungsanleitung

B-K lighting

B-K lighting RE1 Bedienungsanleitung

B-K lighting

B-K lighting BACK BOX Bedienungsanleitung

B-K lighting

B-K lighting YOSEMITE Series Bedienungsanleitung

B-K lighting

B-K lighting PS Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung