Balluff BIC 2I0-IAA50-M30MI3-SM4A5A Bedienungsanleitung

BIC IO-

Link unidirectional

500 mA, IP67, 11 bytes

User´s Guide

www.balluff.com

Content

1User instructions 3

1.1. Validity of the Guide 3

1.2. Typographical Conventions 3

Enumerations 3

Syntax 3

Cross references 3

1.3. Symbols 3

1.4. Abbreviations 3

1.5. Differing views 3

2Safety 4

2.1. Proper Use 4

2.2. Authorized Personnel 4

2.3. Obligations of the Operating Company 4

2.4. Malfunctions 4

2.5. Meaning of the Warning Notices 4

2.6. Certification 4

3Construction and Function 5

3.1. Construction 5

3.2. Function 5

3.3. Features, Advantages 5

3.4. Indicators 5

4Function indicator and diagnosis 6

4.1. Base indicators 6

4.2. Remote indicators 6

5Installation and Connection 7

5.1. Mutual Interference 7

5.2. Installation in Metal 7

5.3. Angular offset 7

5.4. connection 8

5.5. Series connection 8

6Technical Data Base 9

6.1. Dimension 9

6.2. Mechanical data 9

6.3. Operating conditions 9

6.4. Electrical data 9

6.5. Electrical connection 9

7Technical Data Remote 10

7.1. Dimension 10

7.2. Mechanical data 10

7.3. Operating conditions 10

7.4. Electrical data 10

7.5. Electrical connections M12, 5-pin, socket 10

8IO-Link communication 11

8.1. Process data 11

8IO-Link-communication 12

8.2. Parameters 12

8.3. Events 12

Event 1 12

Event 2 12

9Accessories 13

9.1. Connectors 13

9.2. Installation accessories 13

9.3. Active components 13

Balluff Network Interface

www.balluff.com

10 Type Designation Code 14

10.1.Type Code 14

10.2. Order code 14

www.balluff.com

1 User instructions

1.1. Validity of the

Guide

This manual describes the structure, function and installation of the Balluff Uni IO-Link

inductive coupler. It is valid for types:

Base BIC 1I0-IAA50-M30MI3-SM4A4A and

Remote BIC 2I0-IAA50-M30MI3-SM4A5A

Remote BIC 2I0-IAA50-M30MI3-BPX04-002-M45A (see type code)

The guide is intended for qualified technical personnel. Read the guide before you install

and operate the devices.

1.2. Typographical

Conventions

The following typographical conventions are used in this guide.

Enumerations

Enumerations are shown as a list with bullet points.

•Entry 1,

•Entry 2.

Syntax

Numbers

•Decimal numbers are shown without additional indicators (e.g. 123),

•Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex).

Cross references

Cross-references indicate where further information on the topic can be found

1.3. Symbols

Attention!

This symbol indicates a security notice which must be observed.

Note

This symbol indicates general notes.

IO-Link

This device is IO-Link-capable.

1.4. Abbreviations

BIC

EMC

Balluff Inductive Coupler

Electromagnetic Compatibility

Function Grpound

1.5. Differing views

Product views and images in this manual may differ from the product described. They are

intended to serve only as illustrations.

Balluff Inductive Coupler

Base BIC 1I0-IAA50-M30MI3-SM4A4A and

Remote BIC 2I0-IAA50-M30MI3-SM4A5A

Remote BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

www.balluff.com

2 Safety

Important!

Before commissioning, carefully read the operating manual.

2.1. Proper Use

The device is designed to replace a plug connection in order to ensure contact-free data

transmission.

The system must not be used in applications in which the safety of persons is dependent on

the function of the device.

Warranty and liability claims against the manufacturer are rendered void by:

•Unauthorized tampering

•Improper use

•Use, installation or handling contrary to the instructions provided in this operating

manual

2.2. Authorized

Personnel

Installation and commissioning may only be performed by trained specialist personnel.

2.3. Obligations of the

Operating

Company

The operating company must ensure that the locally applicable safety regulations are

observed.

The device corresponds to EMC Class A and can cause radio interference. The operating

company must take appropriate precautions to prevent radio interference.

The device may only be used with an approved power supply. (see "Technical Data"). Only

approved cables may be used.

2.4. Malfunctions

In the event of defects and device malfunctions that cannot be rectified, the device must be

taken out of operation and protected against unauthorized use.

2.5. Meaning of the

Warning Notices

The warning notices in this guide and the measures described for avoiding dangers must be

observed.The warning notices contain the following signal words that indicate the severity of

the danger:

•Danger:

Indicates an immediate danger that will result in a severe injury or death of persons if not

observed.

•Warning:

Indicates a potential danger that may result in a severe injury or death of persons if not

observed.

•Caution:

Indicates a potential danger that may result in light injury to persons or damage to

property if not avoided.

•Attention:

Indicates a situation that may result in property damage if not avoided.

When working with this product, the following warning notices apply:

Caution!

Risk of burning on hot surfaces!

The active surface heats up even under normal operating conditions.

Keep away hands and objects from the active surface.

Avoid contact of metal objects on the active surface. Fire hazard

2.6. Certification

With the CE marking, we confirm that our products meet the requirements of EC

directives 2004/108/EC (EMC) and the EMC law.

In our EMC laboratory, which is accredited by DATech for testing electromagnetic

compatibility, evidence has been provided that the Balluff products satisfy the EMC

requirements of the generic standards:

EN 61000-6-4 (Interference emission) and

EN 61000-6-2 (Immunity to interference)

www.balluff.com

3 Construction and Function

3.1. Construction

The BIC components are designed for applications in an IO-Link system. They are

connected to the host master module via the IO-Link protocol. The system consists of the

following two components:

•Base (master side)

•Remote (device)

The components are enclosed in a brass housing protected acc. to IP 67

Master

The master is connected to the base.

Devices

The remote is connected to the device.

When IO-Link devices are connected, observe the following:

•Make certain that the total power consumption is not greater than that of the base.

•Use only devices with inputs

3.2. Function

This set transfers power from the base to the remote via an air bridge; the base then

receives IO-Link data back from the remote. The base and remote must match one another

with respect to size.

The IO-Link device is wired to the remote. The remote is only inductively coupled to the

base, however. The base transmits the energy for the IO-Link device to the remote. The

IO-Link communication of the IO-Link device is transmitted from the remote to the base.

The energy available for the IO-Link device is dependent on the distance and on the offset

between base and remote and is, therefore, limited. For this reason, the total current

consumption of the connected IO-Link device must not exceed the maximum power output

of the remote.

3.3. Features,

Advantages

•The cable length between the remote and IO-Link device can be a maximum of

20 meters.

•LED indicator on the remote and base for operational readiness and operating voltage

•An angular offset is possible between base and remote

•Simple wiring of e.g. rotary tables, replaceable punch heads etc.

•M12 plug connection on the systems

•Control of capacitive loads

•More power in the same structural shape

•Large operating voltage range

3.4. Indicators

If the supply voltage is applied correctly, the green LEDs on the base and remote illuminate.

If the IO-Link communication is active, the green LED on the base flashes inversely. The

base's red LED illuminates as soon as an error has been detected in the system.

As soon as the remote moves out of the secured working range, the red LEDs on the base

begin to flash. If the red LED illuminates and stays on, there is an error in the IO-Link

communication. If no device is connected to the remote but the remote is within range of the

base, the green LEDs flash.

Balluff Inductive Coupler

Base BIC 1I0-IAA50-M30MI3-SM4A4A and

Remote BIC 2I0-IAA50-M30MI3-SM4A5A

Remote BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

www.balluff.com

4 Function indicator and diagnosis

4.1. Base indicators

Signaling

Function

Green, static

Supply voltage OK

No IO-Link communication

Green, flashing inversely

IO-Link communication between master and base is OK

Red, flashing

No remote detected

Red off

Remote present, IO-Link communication OK

Red, static

Remote present, no IO-Link communication

to connected device

4.2. Remote

indicators

Signaling

Function

Green – static

The remote is located within the working range of a base,

communication between the remote and IO-Link device is

Green, flashing

No IO-Link device present

Green LED status indicator "IO-Link

Green LED status indicator

www.balluff.com

5 Installation and Connection

5.1. Mutual

Interference

Attention!

Improper mounting may affect the function of the system and lead to damage.

The spacings specified for installation must be adhered to.

To prevent mutual interference with adjacent bases or remotes, the specified minimum

distances must be adhered to:

Type

A (mm)

BIC 1I0-IAA50-M30MI3-SM4A4A

100

BIC 2I0-IAA50-M30MI3-SM4A5A

100

BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

100

5.2. Installation in

Metal

Attention!

Device damage due to induction effects!

Metallic objects on the coil cap cause the objects to be heated.

Install the components so that no metallic objects can collect on the coil cap.

There is a fire hazard!

When installing in metal, the specified minimum distances to the surrounding sides of the

metallic object must be maintained. Otherwise, the transmission distance between

transmitter and receiver changes.

The transmission distance can also be influenced by the type of metal.

Type

A (mm)

B (mm)

BIC 1I0-IAA50-M30MI3-SM4A4A

BIC 2I0-IAA50-M30MI3-SM4A5A

BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

5.3. Angular offset

The permissible angular offset ensures proper function, even in difficult installation

conditions:

Distance D (mm)

Angle X

18°

12°

10°

5°

0°

Balluff Inductive Coupler

Base BIC 1I0-IAA50-M30MI3-SM4A4A and

Remote BIC 2I0-IAA50-M30MI3-SM4A5A

Remote BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

www.balluff.com

5Installation and Connection

5.4. Connection

Attention!

Device damage due to incorrect voltage supply!

Malfunctions may occur if the ripple is too high or if the output voltage is not

regulated.

Use only approved, regulated voltage supplies.

Attention!

The remote (receiver) may be damaged by voltage spikes if cables that are too

long are used!

To satisfy the EMC requirements, the receiver cable must not be longer than 20 m.

5.5. Series

connection

Two BIC systems can be connected in series.

Caution!

This cuts the power in half from 500 mA to 250 mA. The cable length between

the individual components in each case must not be larger than 20 m. An

angular offset can no longer be guaranteed. For that reason, the systems

should be positioned accurately. It is not possible to have an air gap larger than

5mm.

No.

Legend for graphic:

Balluff components

Profibus controller

Balluff power supply

BAE PS-XA-1W-24-050-003

Balluff IO-Link master

BNI PBS-502-001-Z001

4+5

BIC IO-Link system

BIC 1I0-IAA50-M30MI3-SM4A4A

BIC 2I0-IAA50-M30MI3-SM4A5A

BIC 2I0-IAA50-M30MI3-BPX04-002-M45A

Balluff sensor hub

BNI IOL-104-000-K006

Balluff sensor hub alternative to 6

BNI IOL-104-000-K021

www.balluff.com

6 Technical Data Base

6.1. Dimension

6.2. Mechanical data

Housing material

Brass

Degree of protection as per

IEC 60529

IP 67 (only in plugged-in and screwed-down state)

Connection type

M12, A-coded

Dimensions (D x L in mm)

M30 X 100

Weight

Approx. 160 g

Tightening torque

70 Nm

6.3. Operating conditions

Transmission distance

1 to 5 mm

Operating temperature T

0 °C to 55 °C

Storage temperature range

-25 °C to 75 °C

6.4. Electrical data

Supply voltage

24 V DC +-10%, acc. to EN 61131-2

Operating current at 24 V

Max. 1 A

Standby current

Max. 100 mA

Overload protection

Yes

6.5. Electrical connection

M12, 4-pin, connector

Signal

Meaning

+24 V

Input voltage

GND,

C/Q, IO Link

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Balluff Zubehör Handbücher

Balluff

Balluff BKT 67M-003-U-S92 Bedienungsanleitung

Balluff

Balluff BOS R080K-UIM-RE10 Series Bedienungsanleitung

Balluff

Balluff BSI R65K0-HXXA-M-S92 Series Bedienungsanleitung

Balluff

Balluff BES M18MH2-GNX50B-BT02-EXA Bedienungsanleitung

Balluff

Balluff BOD 26K Series Service-Handbuch

Balluff

Balluff BES M12MG2-GNX20B-S04G-EXC Bedienungsanleitung

Balluff

Balluff BML-S1H1 Series Bedienungsanleitung

Balluff

Balluff BTL5-T1 Series Bedienungsanleitung

Balluff

Balluff BAE SA-OH-035-PP-S92G Bedienungsanleitung

Balluff

Balluff BOS 73 K Series Bedienungsanleitung

Balluff

Balluff BCS F01 Series Bedienungsanleitung

Balluff

Balluff BTL6-V55 Series Merkblatt

Balluff

Balluff BFS 33M-GSI-F01-S75 Bedienungsanleitung

Balluff

Balluff BSP B P00S2B-S4 Series Bedienungsanleitung

Balluff

Balluff BAM PC-TL-020-K Series Bedienungsanleitung

Balluff

Balluff BOS R090K Series Bedienungsanleitung

Balluff

Balluff BAE SA-OH-059-YI-DP02 Bedienungsanleitung

Balluff

Balluff BES M12MG2-GNX40F-BT02-EXA Bedienungsanleitung

Balluff

Balluff BSI Q41K0-X-M Series Bedienungsanleitung

Balluff

Balluff BSP-B Series Bedienungsanleitung

Balluff

Balluff BOS 21M-UUI-RP30-S4 Bedienungsanleitung

Balluff

Balluff BES M30MH2-GNX10B-S04G-EXC Bedienungsanleitung

Balluff

Balluff BOD 23K Bedienungsanleitung

Balluff

Balluff BOS R090K Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung