Balluff BOL 27K-NS-01-S115 Bedienungsanleitung

Balluff Inc.

Beginning Edge Setup Procedure for the BOL 27K-PS/NS-01-S115

Optical Line Sensor

Setting up the sensor

Note:Assuming factory defaults upon setup. To reset the sensor, enter

the MENU (step 4 below) and press the + button until RESET (rESE) is

displayed. Press the SET button.

1) Place a 150mm strip of reflective tape (BOL 27K-TAPE-01) on a flat surface

90˚ to the face of the sensor.

2) Maximum sensing height is 200mm. Measurement range on tape is 150mm at

this distance. (Note: at closer distances, the analog scale will be less).

3) Once the sensor is mounted, press and hold the +and –buttons

simultaneously for a minimum of 6 sec. until TAPE flashes. (The area of the

tape has been taught and the 4-20mA scale has been designated).

4) Press the SET button for a minimum of 6 sec. MENU will display on the

screen.

5) Press the +button until SAVE is displayed.

6) Press the SET button to save the beginning edge mode.

Note: The sensor will automatically default to a ready state if a button has not been

pushed within 8 seconds while programming. If a mistake is made upon setup, wait a

minimum of 8 sec for the sensor to exit the programming mode and reset to factory

defaults.

Note: The measured object does not have to completely remain within the measureable

window on the tape during area measurement mode. Edges of material can extend

beyond range of sensor.

Setting Tolerances for Discrete Output

The discrete output can be triggered to turn on between two values.

1) Place the material under the sensor to determine where the desired tolerance

levels will be set (referencing the value displayed on the sensor screen for

high and low values).

2) Press the + button for a minimum of 2 sec. Th_1 will be displayed.

3) Press the SET button.

4) Press the + or – button to increment/decrement the value where the discrete

output setting is desired to turn on.

5) Hold the SET button for a minimum of 1 sec to save the low-end point.

6) Repeat steps 2-5 and select Th_2 in this procedure to teach the high-end point

where the discrete output will turn off.

Balluff Inc.

CONNECTION

M12 CONNECTOR

* Available only for the versions with RS485 serial interface (consult factory).

NOTE: The wire colors are referred to the cables manufactured according to the

European standard.

FUNCTIONING

The BOL 27K-PS/NS-01 sensor is a line sensor.

The typical functioning diagram is shown in the drawing given below. The object to

detect is placed in front of the sensor and the reflecting tape (inside the package) behind

the sensor. The sensor illuminated with IR lights the tape and receives the reflected light

on a photodiode array. Each object placed between the reflecting tape and the sensor is

naturally detected as a dark spot on a luminous background.

The sensor has 5 operating modes:

•Object beg.: the position of the first object edge is detected

•Object end: the position of the second object edge is detected

•Object center: the centre of the object is measured

•Width: the distance between the first and last object edge is measured

•Area: the sum of all the object obscured zones is measured

The following diagram shows the sensor output according to the possible object position

inside the meaurement zone.

Balluff Inc.

First ob.

edge

Last ob.

edge

Center

Width

Area

Beg

End

(Beg+End)/2

End-

Beg

End-

Beg

End

Beg

1023-

Beg

1023

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Balluff Zubehör Handbücher

Balluff

Balluff BIS M-628-075-A01-03-ST34 Bedienungsanleitung

Balluff

Balluff BOS 18K Series Bedienungsanleitung

Balluff

Balluff BSP B P00S2B-S4 Series Bedienungsanleitung

Balluff

Balluff BTL7-A5 Series Bedienungsanleitung

Balluff

Balluff BOS 50K RD11-S4 Series Bedienungsanleitung

Balluff

Balluff BOL 27K-PS/NS-01 Bedienungsanleitung

Balluff

Balluff BOS R254K-UUI-LH11-S4 Bedienungsanleitung

Balluff

Balluff BML-S1H1 Series Bedienungsanleitung

Balluff

Balluff BAE SA-OH-035-PP-S92G Bedienungsanleitung

Balluff

Balluff BES M30MH2-GNX10B-BT02-EXA Bedienungsanleitung

Balluff

Balluff BOS R090K Series Bedienungsanleitung

Balluff

Balluff BAE SA-OH-063-NP-DP02 Bedienungsanleitung

Balluff

Balluff BBES M18MF2-PSC80F-BV02-EXD Bedienungsanleitung

Balluff

Balluff BOD 23K Bedienungsanleitung

Balluff

Balluff BES M12MG2-GNX40F-BT02-EXB Bedienungsanleitung

Balluff

Balluff BES05L2 Bedienungsanleitung

Balluff

Balluff BOS 73 K Series Bedienungsanleitung

Balluff

Balluff BKT 67M-003-U-S92 Bedienungsanleitung

Balluff

Balluff BTL7 Series Bedienungsanleitung

Balluff

Balluff BFS 33M-GSI-F01-S75 Bedienungsanleitung

Balluff

Balluff BOS 63M LH13-S4 Series Bedienungsanleitung

Balluff

Balluff BAM-MD-VS-001-002 Bedienungsanleitung

Balluff

Balluff BML-R01-M Series Bedienungsanleitung

Balluff

Balluff BES M30MH2-GNX15F-BT02-EXB Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung