Balluff MICROPULSE+ BTL7-E501-M Series Bedienungsanleitung

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

User's Guide

english

www.balluff.com

www.balluff.com 3english

1 Notes to the user 5

1.1 Validity 5

1.2 Symbols and conventions 5

1.3 Scope of delivery 5

1.4 Approvals and markings 5

2 Safety 6

2.1 Intended use 6

2.2 General safety notes for the position measuring system 6

2.3 Explanationof the warnings 6

2.4 Disposal 6

3 Construction and function 7

3.1 Construction 7

3.2 Function 8

3.3 LED display 8

4 Installation and connection 9

4.1 Installing the transducer 9

4.2 Captive magnets 9

4.3 Floating magnets 10

4.4 Electrical connection 11

4.4.1 Connector S32/cable connection KA_ _ 11

4.4.2 Connector S115 11

4.5 Shielding and cable routing 12

5 Startup 13

5.1 Starting up the system 13

5.2 Operating notes 13

6 Conﬁguration with the Micropulse Conﬁguration Tool 14

6.1 Value table for factory setting 14

6.2 Micropulse Conﬁguration Tool 14

6.3 Connecting the USB communication box 14

6.4 Conﬁguration options 15

7 Technical data 16

7.1 Accuracy 16

7.2 Ambient conditions 16

7.3 Supply voltage (external) 16

7.4 Output 16

7.5 Communication lines La, Lb 16

7.6 Dimensions, weights 17

8 Accessories 18

8.1 Captive magnets 18

8.2 BTL2-GS10-_ _ _ _-A joint rod 18

8.3 Floating magnets 19

8.4 Connectors and cables 20

8.4.1 BKS-S32/S33M-00, freely conﬁgurable 20

8.4.2 BKS-S232/S233-PU-_ _, preassembled 20

8.4.3 BKS-S115/S116-PU-_ _, preassembled 21

8.5 USB communication box 21

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

4english

9 Type code breakdown 22

10 Appendix 23

10.1 Converting units of length 23

10.2 Part label 23

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

www.balluff.com 5english

1.1 Validity

This guide describes the construction, function and setting

options for the BTL7 Micropulse Transducer with analog

interface. It applies to types BTL7-A/E501-M____-P-

S32/S115/KA__ (see Type code breakdown on

page22).

The guide is intended for qualified technical personnel.

Read this guide before installing and operating the

transducer.

1.2 Symbols and conventions

Individual handling instructions are indicated by a

preceding triangle.

►Handling instruction 1

Handling sequences are numbered consecutively:

1. Handling instruction 1

2. Handling instruction 2

Note, tip

This symbol indicates general notes.

Symbols of this type indicate the LED displays.

1.3 Scope of delivery

– BTL7 transducer

– Mounting clamps with insulating sleeves and screws

– Condensed guide

The magnets are available in various models

and must be ordered separately.

1.4 Approvals and markings

UL approval

File no.

E227256

US Patent 5923164

The US patent was awarded in connection with this

product.

The CE Mark verifies that our products

meet the requirements of the current

EMC Directive.

The transducer meets the requirements of the following

product standard:

– EN61326-2-3 (noise immunity and emission)

Emission tests:

– RF emission

EN55011

Noise immunity tests:

– Static electricity (ESD)

EN 61000-4-2 Severity level 3

– Electromagnetic fields (RFI)

EN 61000-4-3 Severity level 3

– Electrical fast transients (burst)

EN 61000-4-4 Severity level 3

– Surge

EN 61000-4-5 Severity level 2

– Conducted interference induced by

high-frequency fields

EN 61000-4-6 Severity level 3

– Magnetic fields

EN 61000-4-8 Severity level 4

More detailed information on the guidelines,

approvals, and standards is included in the

declaration of conformity.

1 Notes to the user

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

6english

2.1 Intended use

The BTL7 Micropulse Transducer, together with a machine

controller (e.g. PLC), comprises a position measuring

system. It is intended to be installed into a machine or

system. Flawless function in accordance with the

specifications in the technical data is ensured only when

using original BALLUFF accessories. Use of any other

components will void the warranty.

Opening the transducer or non-approved use are not

permitted and will result in the loss of warranty and liability

claims against the manufacturer.

2.2 General safety notes for the position

measuring system

Installation and startup may only be performed by

trained specialists with basic electrical knowledge.

Qualified personnel are those who can recognize

possible hazards and institute the appropriate safety

measures due to their professional training, knowledge,

and experience as well as their understanding of the

relevant conditions pertaining to the work to be done.

The operator is responsible for ensuring that local safety

regulations are observed.

In particular, the operator must take steps to ensure that a

defect in the position measuring system will not result in

hazards to persons or equipment.

If defects and unresolvable faults occur in the transducer, it

should be taken out of service and secured against

unauthorized use.

2.3 Explanationof the warnings

Always observe the warnings in these instructions and the

measures described to avoid hazards.

The warnings used here contain various signal words and

are structured as follows:

SIGNAL WORD

Hazard type and source

Consequences if not complied with

►Measures to avoid hazards

The individual signal words mean:

NOTICE!

Identifies a hazard that could damage or destroy the

product.

DANGER

The general warning symbol in conjunction with the

signal word DANGER identifies a hazard which, if not

avoided, will certainly result in death or serious

injury.

2.4 Disposal

►Observe the national regulations for disposal.

2 Safety

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

www.balluff.com 7english

3.1 Construction

Electrical connection: The electrical connection is made

via a cable or a connector (see Type code breakdown on

page22).

Housing: Aluminum housing containing the waveguide

and processing electronics.

Magnet: Defines the position to be measured on the

waveguide. Magnets are available in various models and

must be ordered separately (see Accessories on

page18).

Nominal length: To optimally adapt the transducer to the

application, nominal lengths from 50mm to 7620mm are

available.

3 Construction and function

12 72 73

~80 ~80~250 ~250

36.8

~23

13.8

max. 7

1) Unusable area

2) Not included in scope

of delivery

1) Nominal length =

Measuring range

Null point End point

Output signal rising:

Error signal

100 %

0 %

BTL5-P-3800-2 magnet

Mounting clamps with insulating bushes

and ISO4762M5x22 cylinder-head screws,

max. tightening torque 2Nm

BTL7…-KA_ _

BTL7…-S32BTL7…-S115

Fig. 3-1: BTL7… transducer, construction

Groove

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

8english

3Construction and function (continued)

3.2 Function

The BTL7 transducer contains the waveguide which is

protected by an aluminum housing. A magnet is moved

along the waveguide. This magnet is connected to the

system part whose position is to be determined.

The magnet defines the position to be measured on the

waveguide.

An internally generated INIT pulse interacts with the

magnetic field of the magnet to generate a torsional wave

in the waveguide which propagates at ultrasonic speed.

The component of the torsional wave which arrives at the

end of the waveguide is absorbed in the damping zone to

prevent reflection. The component of the torsional wave

which arrives at the beginning of the waveguide is

converted by a coil into an electrical signal. The travel time

of the wave is used to calculate the position. Depending

on the version, this information is made available as a

voltage or current with rising or falling gradient.

The following functions can be selected for the output

values:

– Position

– Speed (with or without leading sign)

– Differential position

Two outputs that can be independently assigned are

available. Two magnets can be used.

The entire function scope can only be

configured with the PC software "Micropulse

Configuration Tool". To do this, the USB

communication box must be connected (see

Accessories on page18).

3.3 LED display

Fig. 3-2: BTL7 LED displays

In normal operation, the LEDs indicate the

operating states of the transducer. LED1 is

assigned to output1 and LED2 is assigned to

output2.

LED1/LED2 Operating state

Green Normal function

Magnet is within the limits.

Red Error

No magnet or magnet outside the limits.

Flashing green Programming mode

LED 2

LED 1

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

www.balluff.com 9english

4.1 Installing the transducer

NOTICE!

Improper installation

Improper installation can compromise the function of the

transducer and result in damage.

►For this reason, ensure that no strong electrical or

magnetic ﬁelds are present in the immediate vicinity

of the transducer.

►The recommended spacing for the installation must

be strictly observed.

Any orientation is permitted. Mount the transducer on a

level surface of the machine using the provided mounting

clamps and cylinder-head screws. A sufficient number of

mounting clamps is supplied.

In order to avoid the development of resonant

frequences from vibration loads, we

recommend arranging the mounting clamps at

irregular intervals.

The transducer is electrically isolated from the machine

with the supplied insulating bushes (see Fig. 3-1).

1. Guide the transducer into the mounting clamps.

2. Attach transducer to the base using mounting screws

(tighten screws in the clamps with a max.2Nm).

3. Insert magnet (accessories).

The micropulse transducer in profile housing is

suitable both for floating, i.e.non-contacting

magnets (see Fig. 4-4 toFig. 4-8) and for

captive magnets (see Fig. 4-1 to Fig. 4-3).

4.2 Captive magnets

The following must be observed when installing the

magnet:

– Avoid lateral forces.

– Connect the magnet to the machine member with a

joint rod (see Accessories on page18).

Fig. 4-1:

66.4

Dimensions and distances with BTL5-F-2814-1S magnet

Fig. 4-2:

52.5

47.5

Dimensions and distances with BTL5-T-2814-1S magnet

Fig. 4-3:

Dimensions and distances with BTL5-M/N-2814-1S magnet

BTL5-M-2814-1S BTL5-N-2814-1S

Distance X 48.5mm 57mm

Distance Y 51mm 59.5mm

Tab. 4-1: Distances with BTL5-M/N-2814-1S magnet

4 Installation and connection

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

10 english

4Installation and connection (continued)

4.3 Floating magnets

The following must be observed when installing the

magnet:

– To ensure the accuracy of the position measuring

system, the magnet is attached to the moving member

of the machine using non-magnetizable screws

(stainless steel, brass, aluminum).

– The moving member must guide the magnet on a track

parallel to the transducer.

– Ensure that the distance A between parts made of

magnetizable material and the magnet is at least

10mm (see Fig. 4-4 toFig. 4-8).

– Maintain the following values for distance B between

the magnet and transducer and for center offsetC (see

Fig. 4-4 toFig. 4-8):

Type of magnet DistanceB1) OffsetC

BTL5-P-3800-2 0.1…4mm ±2mm

BTL5-P-5500-2 5…15mm ±15mm

BTL5-P-4500-1 0.1…2mm ±2mm

BTL6-A-3800-2 4…8mm2) ±5mm

BTL6-A-3801-2 4…8mm2) ±5mm

2) The selected distance must stay constant over the entire measuring length.

1) For optimum measurement results, a distanceB of 6 to 8mm is

recommended.

Tab. 4-2: Distance and offset for floating magnets

Fig. 4-4:

50+4

55+4

Dimensions and distances with BTL5-P-3800-2 magnet

Fig. 4-5:

61+10

66+10

Dimensions and distances with BTL5-P-5500-2 magnet

Fig. 4-6:

74+4

69+4

Dimensions and distances with BTL6-A-3800-2 magnet

Fig. 4-7:

63+4

58+4

Dimensions and distances with BTL6-A-3801-2 magnet

Fig. 4-8:

81+2

57.5+2

Dimensions and distances with BTL5 -P-4500-1

electromagnet (24V/100mA)

The measuring range is offset by 4mm towards

the transducer plug (see Fig. 4-8).

Plug with

LED

BTL7-A/E501-M _ _ _ _ -P-S32/S115/KA _ _

Micropulse Transducer in a Profile Housing

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Balluff Industrieanlagen Handbücher

Balluff

Balluff BOS R254K-UUI-LH10-S4 Bedienungsanleitung

Balluff

Balluff Micropulse BTL7-S510B Series Bedienungsanleitung

Balluff

Balluff BTL7-A/E501-M Series Bedienungsanleitung

Balluff

Balluff BTL7-P511-M Series Bedienungsanleitung

Balluff

Balluff BCS Q40BBAA-PIM20C-EP-GS04 Series Bedienungsanleitung

Balluff

Balluff MATRIX VISION BAM LS-VS-008-C2 Series Bedienungsanleitung

Balluff

Balluff BTL6-A/G Series Bedienungsanleitung

Balluff

Balluff BTL PF 400 Series Bedienungsanleitung

Balluff

Balluff BNI IOL-104-011-K006 Bedienungsanleitung

Balluff

Balluff BTL6-A500/B50 M Series Bedienungsanleitung

Balluff

Balluff Ethernet/IP BTL7-V50D Series Merkblatt

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung

Balluff

Balluff BTL PA0400 Series Bedienungsanleitung

Balluff

Balluff BTL PA0400 Series Bedienungsanleitung

Balluff

Balluff BMF 423K-AA C-2 Series Bedienungsanleitung

Balluff

Balluff BTL5-S1-M/U-K-SR32/K Series Stücklistenhandbuch

Balluff

Balluff BAE SA-OH-061-UA-DP02 Bedienungsanleitung

Balluff

Balluff BTL7-A510-M-SF-F Series Bedienungsanleitung

Balluff

Balluff BTL7-P511-M-P-S32/KA Series Bedienungsanleitung

Balluff

Balluff BNI CCL-104-100-Z001 Bedienungsanleitung

Balluff

Balluff BIS U-6020-053-10 RS232 Handbuch

Balluff

Balluff BIC 1I3-P2A50-M30MI3-SM4ACA Bedienungsanleitung

Balluff

Balluff BTL6-V1 E-M Series Bedienungsanleitung

Balluff

Balluff BDG E 40-BA Series Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung