Bang & Olufsen BeoLab 7-1 Bedienungsanleitung

Guide

BeoLab 7-1

BeoLab 7-2

Cautions!

– Make sure that the loudspeaker

is placed and connected in

accordance with the instructions

in this Guide.

– Do not attempt to open the loud-

speaker. Leave such operations

to qualiﬁed service personnel!

– The loudspeaker is designed for

indoor use in dry, domestic

environments only, and for use

within a temperature range of

10–40º C (50–105º F).

– In order not to block the sound

emitting from the rear bass reﬂex

ports and the bass units on the

bottom, leave a minimum of

6 cm (2½") free space behind and

below the loudspeaker.

– Always place the loudspeaker in

a horizontal position, and do not

place any items on it.

– Prolonged listening at high

volume levels may cause hearing

damage!

WARNING: To prevent ﬁre or electric

shock, do not expose this appliance to

rain or moisture. Do not expose this

equipment to dripping or splashing

and ensure that no objects ﬁlled with

liquids, such as vases, are placed on

the equipment.

To completely disconnect this equip-

ment from the AC Mains, disconnect

the power supply cord plug from the

AC receptacle.

This symbol indicates that a

dangerous voltage constituting

a risk of electric shock is pres-

ent within this unit.

This symbol indicates that there

are important operating and

maintenance instructions in the

literature accompanying this

unit.

CAUTION: To reduce the risk of

electric shock, do not remove

cover (or back).

No User-serviceable parts inside.

Refer servicing to qualified

service personnel.

Daily use

When you have ﬁnished setting

up the loudspeaker as described

on the following pages, connect

the entire system to the mains.

Loudspeaker protection

The loudspeaker is equipped with a

thermal protection system which

prevents damage from overheating.

If an error occurs – or the speaker

units become overheated – the

system automatically switches the

loudspeaker to standby.

To restore the sound:

> Disconnect the loudspeaker from

the mains.

> Allow the system time to reset or

cool down (approximately 3–5

minutes).

> Reconnect the loudspeaker to the

mains.

Should the problem persist, contact

your Bang & Olufsen retailer.

Cleaning the loudspeaker

Clean dusty surfaces using a dry,

soft cloth. If necessary, remove

grease stains or persistent dirt with

a lint-free, ﬁrmly wrung cloth,

dipped in a solution of water

containing only a few drops of

mild detergent, such as washing-

up liquid.

The loudspeaker front grill may be

cleaned with a vacuum cleaner with

a soft brush nozzle, and set to the

lowest level.

Never use alcohol or other solvents to

clean any parts of the loudspeaker!

Switching on and off

When you switch on your Bang &

Olufsen system, the loudspeaker

switches on simultaneously, and

when you switch the system off

again the loudspeaker also switches

off.

Caution: Handle the loudspeaker

front grill with great care. Dents

and scratches are not covered by

the guarantee!

Set up the loudspeaker

We recommend that you follow

this procedure:

– Disconnect your Bang & Olufsen

system from the mains.

– Mount the loudspeaker to the

Bang & Olufsen stand or wall

bracket as explained on the next

page.

– Connect the loudspeaker as

explained in ‘Cable connections’

(pp. 6–7).

– Set the POSITION switch to the

correct setting. This is explained

in ‘Adapt the loudspeaker to

your room’ (pp. 8–9).

– Connect the entire system to the

mains again.

In order not to dent or scratch the

loudspeaker front grill, we

recommend that you lift the loud-

speaker by holding on to the two

bass units on the bottom. Do not

support the loudspeaker holding

the loudspeaker front grill!

BeoLab 7 brackets: The loud-

speaker must be fastened to one of

the brackets shown here, and on a

suitable Bang & Olufsen stand or

wall bracket.

BeoLab 7-1: Always use the ‘type 1

bracket’.

BeoLab 7-2: Use the ‘type 2

bracket’ when the loudspeaker will

be fastened to one of the ‘double-

column’ Bang & Olufsen stands.

However, use the ‘type 1 bracket’

if the loudspeaker will be fastened

to a wall bracket – for example

below a BeoVision 4 screen.

100 cm

39"

124 cm

49"

‘Type 1 bracket’

‘Type 2 bracket’

BeoLab 7-1

BeoLab 7-2

Here is shown how to fasten

the loudspeaker with a ‘type 1

bracket’ to a Bang & Olufsen

‘single-column’ stand (or wall

bracket). Use the same

procedure if you wish to fasten

the loudspeaker to a Bang &

Olufsen ‘double-column’ Stand

– with a ‘type 2 bracket’.

a Remove the small cover (if any)

on the stand. Press the cover as

shown, and it will come loose.

b Fasten the bracket to the stand or

wall bracket. Use the two longest

screws (M5 × 25 mm) – four

screws for a ‘type 2 bracket’.

c Fasten the loudspeaker to the

bracket. Use the two shortest

screws (M5 × 8 mm). However, do

not fully tighten the screws before

you have made the adjustments

mentioned below (d). Adjustments: First, make sure that

the television is adjusted to a level

position on its stand or wall bracket!

Then use the two screws (d) to

adjust the loudspeaker so that it is

parallel to the lower edge of the

television. Align the loudspeaker

front with the television and tighten

the two screws (c).

b c

NOTE! BeoVision 7 and its

accessories are not available on all

markets.

Cable connections

The loudspeaker is primarily

intended to be used in a setup

with BeoVision 7*. It may, how-

ever, be used with other Bang &

Olufsen systems as well – for

example in a BeoVision 4 setup.

If used in a setup not including

BeoVision 7, you will require a

mains cord and a Power Link

cable. These cables are available

as optional accessories from

your Bang & Olufsen retailer. Mains connections

The loudspeaker has two sockets

concerning mains supply.

The socket marked ~ is for mains

supply input (connection from the

wall outlet), and the other is a mains

supply output to BeoVision 7 (this

socket is not available on loud-

speakers intended for the US-

market).

Note: The mains cord from the wall

outlet must be fastened to the

cable clamp on the loudspeaker –

as shown on the next page.

POSITION switch

This switch has two settings: F

(Free-standing position) and W

(Wall position).

Which setting to use is explained in

‘Adapt the loudspeaker to your room’

(pp. 8–9).

POWER LINK socket

Use this socket to connect the loud-

speaker to one of the Power Link

sockets on the Bang & Olufsen

system – see the next page.

Mains connection

to BeoVision 7

POSITION switch Cable clamp

POWER LINK

socket

The socket panel is located on the rear of the loudspeaker.

*NOTE! BeoVision 7 and its

accessories are not available on all

markets.

Connection to other Bang &

Olufsen systems …

Use a Power Link cable of the

correct type to connect the loud-

speaker to a Power Link socket on

the Bang & Olufsen system.

For further information, refer to the

Guide enclosed with the Bang &

Olufsen system.

Power Link cable: Do not use a

cable of the older type, as this will

cause noise, and therefore not give

optimum sound quality! The new

type has a triangular mark on the

plug.

Connection to BeoVision 7 …

Connect the loudspeaker to one of

the Power Link sockets on the left

BeoVision 7 socket panel.

For further information about the

BeoVision 7 socket panels, refer to

the Guides enclosed with the

product.

The two mains cords and the

Power Link cable are enclosed with

BeoVision 7.

Cable clamp: For safety reasons,

the mains cord from the wall outlet

must be secured to the loudspeaker.

To do so, tug the cord behind the

clamp.

Power Link

Mk 3

BeoVision 7

BeoLab 7

Adapt the loudspeaker to your room

When a loudspeaker is placed

in a corner or close to a wall,

the bass level is boosted

compared to the bass level from

a loudspeaker placed in a more

free-standing position.

To remove this excessive bass

boost, use the POSITION switch

to ensure that the bass level

suits the placement of the

loudspeaker. The appropriate

switch setting depends on the

distance from the loudspeaker

to the walls and corners of the

room.

The POSITION switch

• F (Free-standing position)

Use this setting if the loudspeaker

is placed so that the front grill is

more than 50 cm (20") from the

rear wall, for example on one of

the ﬂoor or table stands.

• W (Wall position)

Use this setting if the loudspeaker

is placed so that the front grill is

less than 50 cm (20") from the rear

wall.

Always use this setting if the loud-

speaker is placed on any of the wall

brackets, but also when placed on

one of the stands – close to the

rear wall.

If the loudspeaker is ﬁtted to one

of the table stands – and you have

chosen to place it on the ﬂoor – you

should set the POSITION switch to

The POSITION switch is located on

the loudspeaker socket panel.

How to measure … The distance

is measured as shown here – the

loudspeaker seen from above.

F W

To get access to the approval

labels, remove the loudspeaker

front grill:

Push the front grill towards the left

(~ 10 mm). The front grill can now

be removed.

Note: When attaching the front

grill again, make sure that all five

‘attach-points’ engage with the

corresponding brackets on the loud-

speaker. Do not attempt to mount

the front grill upside down (marked

on the rear by ).

Caution: Handle the loudspeaker

front grill with great care. Dents

and scratches are not covered by

the guarantee!

Andere Handbücher für BeoLab 7-1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bang & Olufsen Sprecher Handbücher

Bang & Olufsen

Bang & Olufsen BEOLAB 8002 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay A9 3rd Generation Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay P6 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3500 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 12-2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab Penta Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 2500 Kurzanleitung

Bang & Olufsen

Bang & Olufsen BeoPlay S8 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 17 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beovox S35 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beovox RL Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound Core Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 9000 MKIII Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 10 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3500 MKII 1601 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 10 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoPlay A1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 4 PC Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay A1 1st Gen Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BOHBLR Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung