Barco R9841810 Bedienungsanleitung
Universal Lamp Replacement Kit
Installation manual
For SLM *8/*10 and R9+/R12+ projectors
R9841810
R5976544/02
04/01/2005
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail: [email protected]
Visit us at the web: www.barco.com
PrintedinBelgium
1. Safety Warnings
1. SAFETY WARNINGS
1.1 Safety warnings during installation
Who may install
The installation must be performed by authorized technical personnel only.
Authorized technical personnel: persons having appropriate technical training and experience necessary to be aware of hazards to
which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons.
Caution risk of electric shock
Before attempting to remove any of the projector’s covers, the projector has to be turned off and disconnected from the wall outlet
to minimize the risk of electric shock.
Cautiononhead
Before starting with the replacement of the lamp unit, always let cool down the projector after operation in order to reduce the heat
on parts in the light path and to avoid burns.
Warning eye damage
Eye damage may result from direct viewing the light produced by the lamp used in this equipment. Always turn off lamp before
opening cover.
1.2 Product care
Installation Kit
The universal lamp replacement Kit R9841810 is designed for use ONLY with the BARCO SLM G8/R8, G10/R10, R9+ and R12+
series projectors.
Replacement parts
When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized re-
placement parts which have the same characteristics as the Barco original part.
Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized
substitutions may void warranty.
Repairable
Under no circumstances are Barco parts repairable by anyone other than Barco.
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005 1
1. Safety Warnings
2R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005
2. Introduction
2. INTRODUCTION
2.1 Content of the kit
Contentofthekit
The lamp kit consists in a lamp housing, Xenon lamp included. That means that the lamp position is factory calibrated following the
X- ,Y- and Z-axis. When observing a decrease in light output during the run time of the lamp, ONLY a realignment following the
Z-axis can solve the light output decrease.
B
A
Image 2-1
Spacers lock nut removal
Only for transport purposes, the 3 lamp housing fixation spacers (A) are fixed to the lamp casing frame by a
lock nut M5 (B). Always remove the lock nuts before inserting the lamp housing into the projector
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005 3
2. Introduction
4R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005
3. Removing the old lamp
3. REMOVING THE OLD LAMP
3.1 Access to the Lamp Unit.
What has to be done
To access the lamp casing, a side panel has to be removed.
Necessary tools
A flatblade screwdriver of 5 mm
Removingthesidepanel
1. Turn with a screwdriver the side panel lock screw (A) a quarter turn counter clockwise.
A
Image 3-1
Unlocking the side cover
2. Pull the right side of the panel towards you and next to the right to remove.
AB
Image 3-2
Lamp cover removal
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005 5
3. Removing the old lamp
3.2 Removing the Lamp Unit.
What has to be done
The lamp unit has to be slid out of the projector frame.
Necessary tools
Flatblade screwdriver of 5mm or Nutdriver of 8mm.
Sliding out the lamp unit
1. Loosen the 3 spacer screws (A) on the lamp house.
A
BA
A
Image 3-3
Loosening the spacer screws
2. Using the provided handle (B), pull the lamp unit out of the projector frame.
B
Image 3-4
Sliding out the lamp housing
Caution: Be careful not to drop the lamp unit (see safety instructions in front of instruction manual)
6R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005
4. Inserting the new lamp Unit
4. INSERTING THE NEW LAMP UNIT
4.1 Installation of the new Lamp Unit.
What has to be done
First remove the lock nut on each spacer screw and next slide the lamp unit into the projector frame.
Necessary tools
Flatblade screwdriver of 5mm or Nut driver 8mm
Installing the lamp unit
1. Remove the lock nut (B) on the 3 spacer screws (A).
B
A
Image 4-1
2. Line up the lamp unit guides (A) with the guides on the projector base (B) and push the unit into the frame until it fits.
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005 7
4. Inserting the new lamp Unit
B
A
Image 4-2
Lamp unit mounting
3. Secure the position of the lamp unit with the 3 spacer screws.
A
A
A
Image 4-3
Lamp unit fixation
4.2 Optical Alignment of the lamp
What may be adjusted!!
The adjustments to the Y-axis and X-axis (balancing the light intensity) are FACTORY PREADJUSTED. Consequently, both ad-
justable screws are anchored by a lock screw and sealed with a warranty label (Destroying the label void the warranty).
ONLY the Optical readjustment to the Z-axis may be done and is recommended after the lamp has operated for many run times. An
optical realignment of the lamp to the z-axis could compensate the decrease in light output.
8R5976544 UNIVERSAL LAMP REPLACEMENT KIT 04/01/2005
Andere Handbücher für R9841810
1
Inhaltsverzeichnis
Andere Barco Projektorzubehör Handbücher
Barco
Barco POLARIZER R812319K Bedienungsanleitung
Barco
Barco R9802352 Bedienungsanleitung
Barco
Barco OverView OVL708 Bedienungsanleitung
Barco
Barco R9840680 Bedienungsanleitung
Barco
Barco XDL Bedienungsanleitung
Barco
Barco R9841550 Kurzanleitung
Barco
Barco PreCa 1280i Bedienungsanleitung
Barco
Barco SIM 7D Bedienungsanleitung
Barco
Barco Graphics 6300 Bedienungsanleitung
Barco
Barco R812302K Bedienungsanleitung
Barco
Barco ClickShare CSE-800 Bedienungs- und Wartungsanleitung
Barco
Barco R9841770 Bedienungsanleitung
Barco
Barco ICMP HDD Bedienungsanleitung
Barco
Barco ClickShare CSE-200 Bedienungsanleitung
Barco
Barco R767302K Bedienungsanleitung
Barco
Barco R9861520NA Bedienungsanleitung
Barco
Barco LX-5 SERIES Bedienungsanleitung
Barco
Barco ClickShare CSE-200 Bedienungsanleitung
Barco
Barco ClickShare CSE-200 Bedienungsanleitung
Barco
Barco CLICK SHARE CS-100 Bedienungsanleitung
