Baxi Fires Division 750 Montageanleitung

5115979

/01

INSTALLER GUIDE

We trust that this guide gives sufficient details to enable this appliance to be installed

and maintained satisfactorily. However, if further information is required, our

Baxi Fires Division Technical Helpline will be pleased to help.

Telephone 08706 061 065 (National call rates apply in the United Kingdom)

In the Republic of Ireland telephone 0044 8706 061 065.

INSTALLER: Please leave this guide with owner

Model 750

INSET LIVE FUEL EFFECT GAS FIRE

INCORPORATING THE

BAXI FIRES DIVISION CONTROL

With

ALPHA, DECADENT,

DREAM, ELEGANT,

ETERNAL or

OBSESSION fascia

(GC No. 32-032-58)

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595221 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

INSTALLER GUIDE

CONTENTS

Section Heading Page

1. SAFETY 4

2. APPLIANCE DATA 5

3. GENERAL INSTALLATION REQUIREMENTS 6

4. PACK CONTENTS 13

5. FIREPLACE CHECK 15

6. IGNITION CHECK 16

7. GAS SUPPLY CONNECTION 17

8. PREPARING APPLIANCE FOR INSTALLATION 18

9. CONVECTION BOX INSTALLATION 19

9.1 Method 1- Front fixing to fireplace surround. 19

9.2 Method 2 - Cable retention. 20

9.3 Floor sealing. 21

10. BURNER INSTALLATION 22

11. FITTING THE FASCIA 23

12. FITTING THE CERAMIC FUEL EFFECT 24

13. FIREFRONT CASTING INSTALLATION 25

14. FULL OPERATING CHECKS 26

14.1 Recheck the control settings. 26

14.2 Lighting the burner. 26

14.3 Operating the burner. 26

15. SPILLAGE AND FLAME SUPERVISION CHECKS 27

16. FINAL REVIEW 28

17. SERVICING & PARTS REPLACEMENT 29

17.1 Checking the aeration setting of the burner. 30

17.2 To remove the ignition microswitch. 30

17.3 To remove the gas shut-off microswitch 30

17.4 To remove the fascia. 31

17.5 To replace the control slide button. 31

17.6 To remove the burner unit. 32

17.7 To remove the electronic ignition generator. 32

17.8 To remove the thermocouple interrupter block. 32

17.9 To remove the pilot unit. 33

17.10 To remove the shut-off tap. 33

17.11 To remove the gas flow rate controller. 34

17.12 To replace the burner. 34

17.13 To remove the main burner injector. 35

17.14 To remove the appliance from the fireplace. 35

Page 3

INSTALLER GUIDE

1. SAFETY

Installer

Before continuing any further with the installation of this appliance please read the

following guide to manual handling.

!The lifting weight of this appliance is as below: -

Model Heat Engine (kg) Firefront (kg) Combined Weight (kg)

Alpha 7.9 2.10 10.00

Dream 7.9 13.35 21.25

Elegant 7.9 2.10 10.00

Eternal 7.9 3.45 11.35

Decadent 7.9 4.00 11.90

Obsession 7.9 3.25 11.15

!One person should be sufficient to lift the fire. If for any reason this weight is

considered too heavy then obtain assistance.

When lifting always keep your back straight. Bend your legs and not your back.

!Avoid twisting at the waist. It is better to reposition your feet.

!Avoid upper body/top heavy bending. Do not lean forward or sideways whilst

handling the fire.

Always grip with the palm of the hand. Do not use the tips of fingers for support.

!Always keep the fire as close to the body as possible. This will minimise the

cantilever action.

!Use gloves to provide additional grip.

!Always use assistance if required.

Page 4

INSTALLER GUIDE

2. APPLIANCE DATA

This product uses fuel effect pieces and a burner compartment rear wall

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate fibres. Excessive exposure to these materials may cause irritation to eyes,

skin and respiratory tract. Consequently, it is important to take care when

handling these articles to ensure that the release of dust is kept to a minimum. To

ensure that the release of fibres from these RCF articles is kept to a minimum,

during installation and servicing we recommend that you use a HEPA filtered

vacuum to remove any dust and soot accumulated in and around the fire before

and after working on the fire. When replacing these articles we recommend that

the replaced items are not broken up, but are sealed within a heavy duty polythene

bag, clearly labelled as RCF waste. This is not classified as “hazardous waste” and

may be disposed of at a tipping site licensed for the disposal of industrial waste.

Protective clothing is not required when handling these articles, but we recommend

you follow the normal hygiene rules of not smoking, eating or drinking in the work

area and always wash your hands before eating or drinking.

This appliance does not contain any component manufactured from asbestos or

asbestos related products.

* When converted using Kit 0595221

The appliance data label is located on a plate at the base of the fire. This can be seen by

removing the front cover casting.

Page 5

INSTALLER GUIDE

Gas Natural (G20) Propane (G31) *

Inlet Pressure 20mbar 37mbar

Input - Max. (Gross) 6.0kW (20,500Btu/h) 6.1kW (20,800Btu/h)

Input - Min. (Gross) 2.7kW (9,212Btu/h) 4.3kW (14,670Btu/h)

Inlet Test Pressure (Cold) 20.0 ± 1.0mbar (8.0 ± 0.4in

w.g.)

37.0 ± 1.0 mbar (14.85 ±

0.4in w.g.)

Gas Connection 8mm pipe 8mm pipe

Burner Injector Stereomatic Cat 82 - 069 Stereomatic Size 128

Pilot & Atmosphere Sensing

Device Copreci Ref. O.D.S

21500/166

Copreci Ref. O.D.S

21500/166 Fitted with RBM

180 - 02 injector

Ignition Electronic

(Battery 9V PP3) Electronic

(Battery 9V PP3)

Aeration See section 17.1 Non-adjustable

3. GENERAL INSTALLATION REQUIREMENTS

3.1 The installation must be in accordance with this guide.

For the user’s protection, in the United Kingdom it is the law that all gas appliances are

installed by competent persons in accordance with the current edition of the Gas Safety

(Installation and Use) Regulations. Failure to install the appliance correctly could lead

to prosecution. The Council for the Registration of Gas Installers (CORGI) requires its

members to work to recognised standards.

In the United Kingdom the installation must also be in accordance with:

All the relevant parts of local regulations.

All relevant codes of practice.

The relevant parts of the current editions of the following British Standards: -

BS EN 1856 Part 1 which replaces BS 715

BS EN 1858 which replaces BS 1289 Part 1

BS EN 1806 which replaces BS 1289 Part 2

BS EN 1856 Part 1 which replaces BS 4543 Part 2

BS 5440 Part 1

BS 5440 Part 2

BS 6461 Part 1

BS 1251

BS 5871 Part 1

BS 6891

In England and Wales, the current edition of the Building Regulations issued by the

Department of the Environment and the Welsh Office

In Scotland, the current edition of the Building Standards (Scotland) Regulations issued

by the Scottish Executive.

In Northern Ireland, the current edition of the Building regulations (Northern Ireland)

issued by the Department of the Environment for Northern Ireland.

In the republic of Ireland the installation must be carried out by a competent person and

installed in accordance with:

a) The current edition of IS 813 “Domestic gas installations”

b) All relevant national and local rules in force.

c) The current building regulations

Where no specific instructions are given, reference should be made to the relevant

British Standard Code of Practice.

3.2 In the United Kingdom, as supplied, this appliance can be installed in the

following situations: -

3.2.1 A masonry chimney with a minimum diameter of 175mm (7”) free from any

obstruction, and with any damper or restrictor plate in the chimney removed or secured,

Page 6

INSTALLER GUIDE

and having a minimum

effective flue height of 3m

(10ft). A masonry chimney

having a correctly installed

flue liner to BS EN 1856

part 1 or BS715 and with a

minimum flue diameter of

125mm is also acceptable.

Chair brick removal may not

be required providing at

least 50mm clearance is

available from the flue outlet

to any fireplace component.

3.2.1.1 ‘Hole-in-the-wall’ Installations

It is recommended that a hearth should be installed as in section 3.9 (See figure 1).

If a reduced depth hearth is fitted, the fire must be installed so that the distance from

the base of the fireplace opening in the wall to the finished floor level is at least 72mm.

Where there is no floor covering or carpet and the floor is of a type that is likely to be

covered in such a way then the distance from the base of the fireplace opening in the

wall to the finished floor level should be increased to at least 147mm.

To protect from the risk of burns and ignition of clothing a tactile separator shall be

used. The hearth detailed in section 3.9 meets the requirements for a tactile separator. If

this is not used then a 625mm long fender, kerb, horizontal bar, or other barrier, being

fixed not less than 50mm above floor level and positioned 300mm in front of the fixing

plane of the fire will meet the requirement.

! If the lower part of the fascia (the firefront) is free standing, the recommended

reduced hearth depth is 100mm. This is necessary to support the firefront (See figure 4

for appliance dimensions).

Page 7

INSTALLER GUIDE

Figure 1. Hearth and fireplace opening dimensions

3.2.2 To a fireplace incorporating a metal flue

box conforming to BS EN 1856 part 1 or

BS715 with a minimum internal depth of

165mm. Incombustible mineral wool

insulation of not less than 50mm thickness

must be applied to the top surface of the

firebox (See figure 2) and it must stand on a

non-combustible hearth (See figure 1).

3.2.3 (See figure 3)

To a fireplace that has a precast concrete or

clay flue block system conforming to BS1289

or BS EN 1858. The appliance is suitable for

installations conforming to older versions of

BS1289 as well as the current edition. The

flue blocks must have a minimum width not

less than 63mm and a cross-sectional area not

less than 13,000mm2.Older editions of

BS1289 required a cross-sectional area of

13,000mm2. The current revision of the

standard requires 16,500mm2. This

appliance is suitable in both cases. The

total depth of the opening measured from

the finished front of the fireplace

(Including plaster, surround etc.) must be

as below:

! If the width at the rear of the precast

flue starter blocks is 300mm or greater the

depth of the opening is to be not less than

138mm. Under these conditions the

eyebolts will need to be located as close to

the sides of the starter blocks as possible.

! If the width at the rear of the precast

flue starter blocks is less than 300mm

then an additional 16mm of depth will be

required to accommodate the eye bolts.

Therefore if the starter blocks are less than

300mm wide the minimum depth of the

opening will be not less than 154mm. Page 8

INSTALLER GUIDE

Figure 3. Pre-cast Fireplace

Figure 2. Metal flue box

The current versions of BS1289 and BS EN 1858 recommend that there should be an air

space or insulation between the flue blocks and the plaster because heat transfer may

cause cracking on directly plastered flues. However, generally this appliance is suitable

for installations under all circumstances unless there is a history of cracking problems.

Remember that faults such as cracking may be caused by poorly built and restrictive

flues, e.g. mortar extrusions, too many bends, flue heights below three metres,

restrictive terminations, etc.

3.2.4 If the fireplace opening is greater than the acceptable dimensions given in this

guide, do not use the back of a fire surround or marble to reduce the opening. This may

cause cracking of the surround back or marble.

3.3 The following flues are suitable:

! 225mm x 225mm conventional brick flue.

If a flue liner is used, it must be a minimum of 125mm diameter. The liner must be

sealed to the surrounding area above the fireplace opening and to the top of the

chimney. An approved terminal must be fitted.

! 200mm diameter factory made insulated flue manufactured to BS 4543 or BS EN

1856 part 1.

! A properly constructed precast flue conforming to B.S 1289 or BS EN 1858.

A flue pipe with a minimum diameter of 175mm. See B.S 6461 Part 1 for suitable

materials. Metal flue pipes must comply with B.S 715.

! Single wall, twin wall or flexible flue liner of minimum diameter 125mm. The

materials used are stainless steel or aluminium as specified in B.S. 715 or BS EN 1856

part 1.

3.3.1 The minimum effective height of the flue must be 3m.

3.3.2 The flue must be clear of any obstruction and its base must be clear of debris.

3.3.3

The flue must be completely sealed so that combustion products do not come into

contact with combustible materials outside the chimney.

3.3.4 The flue must serve only one fireplace.

3.4 The flue must conform to BS 5440: Part 1 in design and installation.

The flue, measured from the bottom of the fireplace opening to the bottom of the

terminal, shall be not less than 3m in actual vertical height. When calculated in

accordance with BS 5440: Part 1 Annex A, the minimum equivalent

height of the flue

shall be 2.0m of 125mm dia. flue pipe.

3.5 The flue must not be used for any other appliance or application.

3.6

Any chimney dampers or restrictors should be removed. If removal is not possible

they must be fixed in the open position.

Page 9

INSTALLER GUIDE

3.7

If the appliance is intended to be installed to a chimney, which was previously used

for solid fuel, the flue must be swept clean prior to installation. All flues should be

inspected for soundness and freedom from blockages.

3.8

If the fireplace opening is an underfloor draught type, it must be sealed to stop any

draughts.

3.9 The appliance must be mounted behind a non-combustible hearth unless the

conditions of section 3.2.1.1 are met (N.B. conglomerate marble hearths are considered

as non-combustible). The appliance can be fitted to a purpose made proprietary class

“O”-150°C surround. The hearth material must be at least 12mm thick. The periphery of

the hearth (or fender) should be at least 50mm above floor level to discourage the

placing of carpets or rugs over it.

The appliance must not stand on combustible materials or carpets (See figure 1).

3.10

The front face of the fireplace should be reasonably flat over the area covered by

the convector box top and side flange seals to ensure good sealing. These faces should

be made good if necessary. The fireplace floor should be reasonably flat to ensure that a

good seal with the convector box can be made.

3.11

The minimum height from the base of the fireplace opening to the underside of

any shelf made from wood or other combustible materials is detailed below.

• For a shelf up to 150mm deep: Minimum height = 750mm.

• For a shelf deeper than 150mm: 750mm + 12.5mm for every 25mm depth over

150mm. (See Graph 1).

Page 10

INSTALLER GUIDE

Graph 1. Combustible shelf clearances

Andere Handbücher für 750

Inhaltsverzeichnis

Andere Baxi Fires Division Kamin im Innenbereich Handbücher

Baxi Fires Division

Baxi Fires Division VALOR FIRES FireSlide 940 Gebrauchsanweisung

Baxi Fires Division

Baxi Fires Division 759 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division Heartbeat Oxysafe 2 Montageanleitung

Baxi Fires Division

Baxi Fires Division 541 Montageanleitung

Baxi Fires Division

Baxi Fires Division 941 Montageanleitung

Baxi Fires Division

Baxi Fires Division 341 Black Beauty Slimline Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 740FS Montageanleitung

Baxi Fires Division

Baxi Fires Division 949 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division soraya 747 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 754 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 756 Montageanleitung

Baxi Fires Division

Baxi Fires Division 956 Montageanleitung

Baxi Fires Division

Baxi Fires Division 746 monaco Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 755 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 750 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division Sonnet Plus Montageanleitung

Baxi Fires Division

Baxi Fires Division Dream BR660VA Montageanleitung

Baxi Fires Division

Baxi Fires Division 750 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 740FS Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division Soraya 746 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 339 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 661 Anthem Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 347 BLACK BEAUTY Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 754 Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch