Baxi Fires Division 750 Bedienungsanleitung

5112499/02

Model750

INSET LIVE FUEL EFFECT GAS FIRE

Fitted with an

Avignon,

Harmonyor

Stylefascia

(GC No. 32-032-58)

This guide to be left with the owner

We trust that this guide gives

sufficient details to enable this

appliance to be operated and

maintained satisfactorily. However, if

further information is required, our

Baxi Fires Division Technical

Helpline will be pleased to help.

Telephone 08706 061 065 (National

call rates apply in the United

Kingdom).

In the Republic of Ireland

Telephone 0044 8706 061 065.

This guide is intended to help you care

for your Baxi Fires Division gas fire.

Please read thoroughly before using

and keep for future reference.

OWNER GUIDE

(including photocopying), stored in any medium by electronic means (including in any

retrieval system or database) or transmitted, in any form or by any means, whether

electronic, mechanical, recording or otherwise, without the prior written permission of

the copyright owner.

Applications for the copyright owner's permission to reproduce any part of this

publication should be made, giving details of the proposed use, to the following address:

The Company Secretary, Baxi Heating UK Limited, Pentagon House, Sir Frank Whittle

Road, Derby, DE21 4XA.

Warning: Any person who does any unauthorised act in relation to a copyright work

may be liable to criminal prosecution and civil claims for damages.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595221 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Page 3

OWNER GUIDE

LIST OF CONTENTS

Section Page

SAFETY 5

APPLIANCE DIMENSIONS 6

GAS CONSUMPTION 7

OPERATING YOUR FIRE 7

The Oxysafe flame sensing and flue blockage safety system. 7

Lighting the pilot. 8

Lighting the main burner. 8

Selecting the heat setting. 8

Turning the fire back to pilot setting. 8

Turning the appliance off. 9

Lighting with a taper. 9

CLEANING YOUR FIRE 9

Metal parts. 9

Ceramic fuel effect and rear wall. 9

Burner. 10

CERAMIC FUEL EFFECT REFITTING 10

MAINTENANCE 10

Regular maintenance. 10

Servicing. 11

USEFUL TELEPHONE NUMBERS 11

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 4

OWNER GUIDE

SAFETY

have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installation instructions

provide a minimum clearance of 750mm from the base of the fireplace opening to

any shelf made of wood or other combustible material where the shelf is not more than

150mm deep. For a shelf deeper than 150mm, add 12.5mm to the clearance for every

25mm of additional shelf depth (See graph1).

Do always use a fireguard complying with BS 8423 for the protection of young

children, the elderly, the infirm or pet animals.

Do wait three minutes before attempting to relight if the fire is switched off or the

Page 5

OWNER GUIDE

Graph 1. Combustible shelf clearances

IF YOU SMELL GAS

! DON’T SMOKE.

! EXTINGUISH ALL NAKED FLAMES.

! DON’T TURN ELECTRICAL SWITCHES ON OR OFF.

! TURN OFF THE GAS SUPPLY AT THE METER.

! OPEN DOORS AND WINDOWS TO GET RID OF THE GAS.

! IMMEDIATELY CALL THE GAS EMERGENCY SERVICE FROM A

NEIGHBOURS PHONE - SEE YOUR LOCAL TELEPHONE DIRECTORY.

flames are extinguished for any reason.(Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire, if for any reason, the flame goes out)

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t put more ceramic fuel effect pieces on the fire than the number given in this

guide or use any ceramic fuel effect pieces other than those authorised for this fire.

Incorrect combustion could result.

Don’t put paper or other materials onto your fire.

Don’t use the fire with damaged base ceramics.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

APPLIANCE DIMENSIONS

Page 6

OWNER GUIDE

Dimension ‘A’ - Projection into room

Model Harmony Avignon Style

Dimension (mm) 68mm 68mm 83mm

Figure 1. Appliance dimensions

Shown with Harmony firefront

GAS CONSUMPTION

Model 750

Has a maximum natural gas input of 6.0kW (Gross)

Has a maximum natural gas output of 3.4kW

Has a minimum natural gas input of 2.3kW (Gross)

Has a minimum natural gas output of 1.2kW

Model 750 when converted using kit number 0595221

Has a maximum propane gas input of 6.1kW (Gross)

Has a maximum propane gas output of 3.5kW

Has a minimum propane gas input of 3.8kW (Gross)

Has a minimum propane gas output of 1.9kW

OPERATING YOUR FIRE

The Oxysafe flame sensing and flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions.

This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control

knob is kept depressed at the “Pilot/Ign” position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

Page 7

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

Lighting the pilot.

This fire is controlled by a 4-position gas tap mounted

on the front leg of the appliance. In addition to the

“Off” position there is a pilot light and 2 heat control

settings (See figure 2).

! Depress the control knob and turn anticlockwise

towards the “Pilot/Ign” position. A spark should be

generated at the pilot while turning. The spark should

ignite the pilot. The pilot flame can be seen through the

lower left hand opening in the front of the fuel effect

bed.

! Keep the button depressed at the “Pilot/Ign” position

for a further ten seconds. This will prevent the flame-

sensing device from shutting off the gas while its probe

warms up.

! If the pilot does not ignite instantly, repeat procedure.

If after 10 seconds pilot ignition has not occurred, turn the control knob back to

the “Off” position, wait for 3 minutes and then repeat the ignition procedure.

Lighting the main burner.

! Once the pilot light is established, the main burner can be lit by depressing and

turning the control knob anticlockwise to the “High” position.

Selecting the heat setting.

In order to change from one setting to another depress the control knob slightly and

turn the knob to the required position. Any setting from “Low” to “High” may be

selected.

Note: The appliance will operate to its maximum potential if the flue is primed during

the first 20-30 minutes of operation. To do this, simply operate the appliance at its

“High” setting. This will also burn off any carbon deposits that may have formed

during previous operations. If operating the appliance for long periods it is beneficial to

change between settings. This will help to remove any carbon deposits that may form

during operation.

Turning the fire back to pilot setting.

! Depress the control knob and turn clockwise until the pilot setting is reached.

Page 8

OWNER GUIDE

Figure 2.

Turning the appliance off.

! Make sure that the control knob is in the pilot position. Depress the control knob

and turn clockwise to the “Off” position.

! Wait at least three minutes before relighting.

Lighting with a taper.

(See figure 3).

In the unlikely event of failure of the ignition spark,

the pilot can be lit by a taper or long spill. Insert the

taper or spill through the lower left hand opening in

the front of the ceramic fuel effect.

! Follow the section ‘ Lighting the pilot’ as

described previously.

CLEANING YOUR FIRE

To maintain the high performance and quality finish of your Baxi Fires Division

appliance, please follow these guidelines:

Before attempting to clean the fire, please remember to turn off the fire and wait for

the appliance to cool completely. The fire will retain heat for some time before cleaning

can begin.

If any pieces of debris are found in the firebox, have the chimney inspected before

further use.

Metal parts.

Clean the metal parts with a slightly damp, lint free non-abrasive cloth and then dry.

! Do not use abrasive cleaners, as these will scratch the fire surface.

! Fascia -

Clean the metal parts with a slightly damp cloth and then dry. If this does

not work apply a very small amount of ‘baby oil’ to a lint free, non-abrasive cloth and

wipe over the surface. Use a clean cloth to wipe off the oil.

Ceramic fuel effect and rear wall.

! This product uses fuel effect pieces and burner compartment rear wall

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate fibres. Excessive exposure to this material may cause irritation to eyes, skin

and respiratory tract. Consequently, it is important to take care when handling

these articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation of the

fire.

! Should any soot accumulation become excessive, the fuel effect pieces and walls

should be removed from the fire for cleaning.

Page 9

OWNER GUIDE

Figure 3. Lighting with a taper

Page 10

Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the

dust.

! We suggest that you remove the ceramic fuel effect in the reverse order to that

shown in the ceramic fuel effect installer and owner guide. This should have been left

inside or attached to this guide by the installer.

Burner.

! The burner surface can be carefully cleaned to remove any loose particles after

taking off the ceramic fuel effect. Make sure that no particles are pushed into the burner

holes.

CERAMIC FUEL EFFECT REFITTING

The installer and owner guide for the ceramic fuel effect is separate from this guide. The

installer may have attached it to this guide or placed it inside. It is important that the

installer and owner guide for the ceramic fuel effect is followed correctly. If replacing

the ceramic fuel effect, where a new guide is supplied, follow the installer and owner

guide supplied with the replacement fuel effect.

Keep the replacement installer and owner guide with this owner guide for future

reference.

MAINTENANCE

Regular maintenance.

In order to achieve and maintain high levels of personal safety and performance

efficiency, it is essential that the opening at the back of the fire and the flue are kept

clear of any form of obstruction. It is possible that deposits of mortar or soot could fall

and accumulate causing the flue to be blocked or restricted and so preventing proper

clearance of dangerous exhaust fumes.

In the United Kingdom it is the law that a landlord must have any gas appliance, flue

and pipework which is situated in a tenant’s premises checked for safety at least every

twelve months by a competent person (In the U.K, a CORGI registered installer).

We recommend that all gas appliances and their flues, wherever situated, are checked

annually.

OWNER GUIDE

Andere Handbücher für 750

Inhaltsverzeichnis

Andere Baxi Fires Division Kamin im Innenbereich Handbücher

Baxi Fires Division

Baxi Fires Division 756 Montageanleitung

Baxi Fires Division

Baxi Fires Division 941 Montageanleitung

Baxi Fires Division

Baxi Fires Division 740FS Montageanleitung

Baxi Fires Division

Baxi Fires Division Heartbeat Oxysafe 2 Montageanleitung

Baxi Fires Division

Baxi Fires Division 956 Montageanleitung

Baxi Fires Division

Baxi Fires Division 746 monaco Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 347 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 339 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 742 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 347 BLACK BEAUTY Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 750 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division Dream BR660VA Montageanleitung

Baxi Fires Division

Baxi Fires Division 740FS Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 541 Montageanleitung

Baxi Fires Division

Baxi Fires Division 750 Montageanleitung

Baxi Fires Division

Baxi Fires Division soraya 747 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 754 Montageanleitung

Baxi Fires Division

Baxi Fires Division 759 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 949 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 742 Montageanleitung

Baxi Fires Division

Baxi Fires Division Soraya 746 Bedienungsanleitung

Baxi Fires Division

Baxi Fires Division 939 Montageanleitung

Baxi Fires Division

Baxi Fires Division Sonnet Plus Montageanleitung

Baxi Fires Division

Baxi Fires Division 739 Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch