Baxi 741 Bedienungsanleitung

5112225/01

OWNER GUIDE

This guide is intended to help you care for your Baxi Fires Division gas fire. Please read

thoroughly before using and keep for future reference.

This guide to be left with the owner.

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595211

THIS APPLIANCE

IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

We trust that this guide gives sufficient details to enable your appliance to be operated

and maintained satisfactorily. However, if further information is required, our

Baxi Fires Division Technical Helpline will be pleased to help.

Please telephone 08706 061 065

(National call rates apply in the United Kingdom). In

the Republic of Ireland telephone 0044 8706 061 065.

Model 741

INSET LIVE FUEL EFFECT GAS FIRE

Fitted with

Blenheim

Sonnet fascia

(GC No. 32-032-56)

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

At the heart of every Baxi Fires Division fire.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

LIST OF CONTENTS

Section Page

SAFETY 4

APPLIANCE DIMENSIONS 5

GAS CONSUMPTION 6

OPERATING YOUR FIRE 6

The Oxysafe flame sensing and flue blockage safety system. 6

To light the fire. 7

Lighting with a taper. 8

CLEANING YOUR FIRE 8

Metal Parts 8

Ceramic fuel effect pieces and burner compartment walls. 8

Burner. 9

CERAMIC FUEL EFFECT REFITTING 9

MAINTENANCE 12

Regular maintenance. 12

Servicing. 12

USEFUL TELEPHONE NUMBERS 12

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 3

OWNER GUIDE

SAFETY

have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installer guide.

allow a minimum clearance of 760 mm from the top of the base of the hotbox to the

underside of any shelf whether it is made from combustible or non-combustible

materials. For a shelf made from wood or other combustible materials deeper than

150mm add 12.5mm to the clearance for every 25mm of additional shelf depth (See

graph 1). Please bear this in mind if ever you add a shelf.

Page 4

OWNER GUIDE

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE - SEE YOUR

LOCAL TELEPHONE DIRECTORY

Graph 1. Combustible shelf clearances.

Do provide a suitable guard that complies with BS 8423 for the protection of young

children, the elderly and the infirm. Such a guard is also recommended for the

protection of pet animals. (Although this fire conforms to all the applicable standards, it

is a heating appliance and certain parts of its surface will become hot).

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason. (Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire if, for any reason, the flames go out).

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are considering altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t

add any extra fuel effect pieces above the number stated in this guide. This could

cause a safety hazard.

Don’t put paper or any other material on the fire.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth.

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

APPLIANCE DIMENSIONS

Page 5

OWNER GUIDE

Figure 1. Appliance dimensions

GAS CONSUMPTION

Model 741

Has a maximum natural gas input of 6.85kW (Gross)

Has a maximum natural gas output of 3.4kW

Has a minimum natural gas input of 2.3kW (Gross)

Has a minimum natural gas output of 0.09kW

Model 741 when converted using kit number 0595211

Has a maximum propane gas input of 6.7kW (Gross)

Has a maximum propane gas output of 3.71kW

Has a minimum propane gas input of 4.0kW (Gross)

Has a minimum propane gas output of 2.10kW

OPERATING YOUR FIRE

The Oxysafe flame sensing and flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions.

This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control

knob is held in at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

Page 6

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

To light the fire.

Depress the control knob and rotate it anticlockwise to the pilot ignition position. A

'click' will be heard as the integral piezo operates. A flame should appear at the pilot.

Keep the control knob depressed and hold the pilot ignition position for five seconds.

When the control knob is released the pilot flame should remain lit. If a flame does not

appear at the pilot then turn the control knob clockwise to the 'OFF' position and repeat

the above.

When the pilot burner is operating properly, gradually turn the control knob anti-

clockwise to 'HIGH' position. (Depress the knob slightly to get past the pilot ignition

position). The main burner should now light.

Depress the control knob slightly to release from

the 'HIGH' position and turn back (clockwise) to

'LOW'. While turning, the burner flames should

gradually become lower but remain alight.

Depress the control knob slightly to release from

the 'LOW' position and turn back (clockwise) to

the Pilot ignition position. The main burner

should extinguish but the pilot should remain

alight. Depress the control knob slightly and turn

back (clockwise) to turn OFF. This will

extinguish the pilot.

While cooling, the ceramic fuel effects may

make some crackling noises. This is quite

normal.

Note i) If the flames go out while setting the control, repeat the full lighting

procedure. If the flames repeatedly go out have the fire serviced.

ii) Please note. When first turned on the flames will appear predominantly

blue. The fuel effect pieces will take time to warm up. Although some glow

will be seen after approximately ten minutes, the full visual effect will only

be apparent after a somewhat longer time.

iii)

The appliance will operate to its maximum potential if the flue is primed

during the first 20 – 30 minutes of operation. To do this, simply slide the

control button to its highest setting. This will also burn off any carbon

deposits that may have formed during previous operations.

iv)

If operating the appliance for long periods it is beneficial occasionally to

change the settings. This will also help

to remove any carbon deposits that

may form during operation.

Page 7

OWNER GUIDE

Figure 2. The Control

Lighting with a taper.

(See figure 3).

In the unlikely event of failure of the ignition spark, the pilot can be lit by a taper or

long spill.

! Turn the control knob to the 'Pilot ignition' position

! Insert the taper or spill between the second

and third left hand ceramic fuel effect pieces on

the first row

! Depress the control knob. A flame should

appear at the pilot.

! Remove the taper and keep the control

depressed for 5 seconds.

! Release the control knob and the pilot flame

should remain alight. If it does not, repeat the

above.

! Turn the control knob to the required setting.

While cooling, the ceramic fuel effect pieces

may make some crackling noises. This is quite

normal.

CLEANING YOUR FIRE

To maintain the high performance and quality finish of your fire please follow these

guidelines:

Before attempting to clean the fire, please remember to turn off the fire and wait for the

appliance to cool. The fire will retain heat for some time before cleaning can begin.

If any pieces of debris are found in the firebox, have the chimney inspected before

further use.

Metal Parts

! Clean the metal parts with a slightly damp cloth and then dry.

! Do not use abrasive cleaners as these will scratch the fire surface.

Ceramic fuel effect pieces and burner compartment walls.

This product uses fuel effect pieces and burner compartment walls containing

Refractory Ceramic Fibres (RCF), which are man-made vitreous silicate fibres.

Excessive exposure to this material may cause irritation to eyes, skin and

respiratory tract. Consequently, it is important to take care when handling these

articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation of the

fire. Should any soot accumulation become excessive, the fuel effect pieces and walls

Page 8

OWNER GUIDE

Figure 3. Lighting with a taper

should be removed from the fire for cleaning.

Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the

dust.

! We do not recommend the use of a normal domestic vacuum cleaner which may

blow dust back into the air.

! We suggest that you remove the ceramic fuel effect pieces in the reverse order to

that shown in this guide.

Burner.

Remove any deposits of soot or other foreign matter from the surface of the burner with

a dry soft brush. Be careful not to brush any particles into the open slots. Remove any

particles from the slots with a vacuum cleaner fitted with a soft brush attachment. Do

not poke wire, etc. into the slots in the burner.

CERAMIC FUEL EFFECT REFITTING

Place the ceramic base coal in the burner compartment. The bottom rear face of the

coal should rest on the angled ledges at the back of the burner compartment. The bottom

front recess edges on the coal base should locate against the tags at the front of the

ceramic support (See figure 4).

Page 9

OWNER GUIDE

Figure 4. Ceramic base location

2. Place the ceramic front coal in position in

front of the base coal. The front of the

ceramic coal should touch the front of the

burner module (See figure 5).

The loose ceramic coals are supplied in three

sizes. There are two large ceramic coals, three

medium ceramic coals and 12 small ceramic

coals. When installing the ceramic coals

smooth surfaces should be positioned to the

bottom or rear unless stated otherwise. Install

the loose coals as follows.

3. Locate the two large ceramic coals at the

ends of the front base ceramic coal. The large

ceramic coals have two sides that are smooth.

Locate one smooth side along the side of the

hotbox and the other to the rear (See figure

6).

4. The top surface of the front ceramic base

coal has three ‘V’ shaped indents.

Locate a small ceramic coal into each indent

(See figure 6).

Page 10

OWNER GUIDE

Figure 6. First row of ceramic coals

Figure 5. Front coal location

Andere Handbücher für 741

Inhaltsverzeichnis

Andere Baxi Kamin im Innenbereich Handbücher

Baxi

Baxi Bermuda SL3 Betriebsanleitung

Baxi

Baxi 748 Bedienungsanleitung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi Classic 2 719 Bedienungsanleitung

Baxi

Baxi 754 Montageanleitung

Baxi

Baxi Brava 4 Oxysafe Bedienungsanleitung

Baxi

Baxi 946 Montageanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi Harmony Montageanleitung

Baxi

Baxi Baxi Belgravia Deluxe Betriebsanleitung

Baxi

Baxi 949 Montageanleitung

Baxi

Baxi 951 Gebrauchsanweisung

Baxi

Baxi 750FS Bedienungsanleitung

Baxi

Baxi 746 Montageanleitung

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 741 Montageanleitung

Baxi

Baxi 748 Montageanleitung

Baxi

Baxi 961 Gebrauchsanweisung

Baxi

Baxi 739 Bedienungsanleitung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi 750M Bedienungsanleitung

Baxi

Baxi Cavendish Deluxe PCF Betriebsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch