BEA COLIBRI ONE DRO Bedienungsanleitung
COLIBRI ONE
/
TWO DRO
5
1
2
4
3
Specifications are subject to changes without prior notice.
Measured in specific conditions
TECHNICAL SPECIFICATIONS
DESCRIPTION
EN
Opening sensors for automatic doors
Technology:
Transmitter frequency:
Transmitter radiated power:
Transmitter power density:
Detection mode:
Min. detection speed:
Supply voltage:
Mains frequency:
Max. power consumption:
Output:
Max. contact current:
Max. contact voltage:
Mounting height:
Degree of protection:
Temperature range:
Dimensions:
Tilt angles:
Material:
Weight:
Cable length:
microwave doppler radar
24.150 GHz
< 20 dBm EIRP
< 5 mW/cm²
motion
5 cm/s (measured in sensor axis)
12 V to 24 V DC +30% / -10% (The Equipment must be powered by a SELV limited power
source ensuring double insulation between primary voltages and the Equipment supply. The supple
current should be limited to 1.5 A.)
50 to 60 Hz
< 2 W
250 mA
50 V DC/V AC
from 1.8 m to 3 m
IP54
from -20 °C to + 55 °C
80 mm (W) x 60 mm (H) x 50 mm (D)
0° to 90° vertical; -30° to +30° lateral
ABS & polycarbonate
70 g
2.5 m
Other use of the device is outside the permitted purpose and can not
be guaranteed by the manufacturer.
The manufacturer cannot be held responsible for incorrect installations
or inappropriate adjustments of the sensor.
Please keep for further use
Designed for colour printing
1. main connector
2. potentiometer for field size adjustment
3. LED
4. radar antenna (wide field)
5. cover
User’s Guide for software version 0100 and higher
(refer to tracking label on product)
COLIBRI ONE DRO : Unidirectional detection
COLIBRI TWO DRO : Bidirectional detection
Before fixing After fixing
Avoid proximity to neon
lamps or moving objects.
Do not cover the sensor.Avoid vibrations.Do not touch electronical
parts.
Wall mounting above sliding or
revolving doors
Ceiling mounting in front of sliding,
revolving or swing doors
(outside of the door motion range)
OPENING THE SENSOR
TIPS
APPLICATIONS
2
23
1
MIN MAX
1
FIELD ADJUSTMENTS
Apply the mounting template.
Drill 1 hole for the cable.
Drill 2 holes for the screws.
Fix the sensor firmly.
ANGLE
2.2 m
2.2 m
Connect the cable and insert it
through the hole.
Connect the wires as follows:
SIZE
field size: max
vertical angle: 30°
2.2 m 2.2 m
MOUNTING & WIRING
BROWN - POWER SUPPLY
GREEN - POWER SUPPLY
WHITE - NO
YELLOW - COM
BEA | A-B Area, 3rd Floor | No.1 Building, No.5 Xinghai Road, Beijing Economic Technological Development Area, Beijing | China
1
1
2
3
1
©BEA | Original instructions | 69.0612 / V3 - 11.20
BEA hereby declares that the equipment type COLIBRI ONE/TWO DRO is in compliance with the
European Directives 2011/65/EU (RoHS), 2014/53/EU (RED). The full text of the EU declaration
of conformity is available on our website.
TROUBLESHOOTING
The door remains
closed.
The LED is OFF.
The sensor power is off. Check the wiring and the power supply.
The door does not
react as expected.
The door closes and
opens constantly.
Improper output
configuration on the sensor.
The sensor is disturbed by
the closing of the door or
vibrations caused by the
door motion.
Make sure the sensor is fixed properly.
Increase the antenna angle.
Reduce the field size.
For EU countries: This product should be disposed of separately from unsorted municipal waste.
Change the output configuration setting on
each sensor connected to the door operator.
SAFETY INSTRUCTIONS
The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system
in compliance with applicable national and international regulations and standards on door safety and if applicable, the machinery
directive 2006/42/EC.
Only trained and qualified personnel may install and setup the sensor.
The warranty is void if unauthorized repairs are made or attempted by unauthorized personnel.
Avoid touching any electronic and optical components.
Dieses Handbuch passt für folgende Modelle
1
Andere BEA Zubehör Handbücher
BEA
BEA FALCON EX Bedienungsanleitung
BEA
BEA PBR45 Series Bedienungsanleitung
BEA
BEA SPARROW Bedienungsanleitung
BEA
BEA SUPERSCAN-T Bedienungsanleitung
BEA
BEA COLIBRI ONE Bedienungsanleitung
BEA
BEA FALCON XL Bedienungsanleitung
BEA
BEA LZR SIGMA Bedienungsanleitung
BEA
BEA Nema 4 Flex IR Bedienungsanleitung
BEA
BEA IRIS Cover Assembly Benutzerhandbuch
BEA
BEA FALCON Bedienungsanleitung
BEA
BEA EAGLE Bedienungsanleitung
BEA
BEA SBK 30 Benutzerhandbuch
BEA
BEA VIO-D Bedienungsanleitung
BEA
BEA IXIO-DT3 Bedienungsanleitung
BEA
BEA IS40 Bedienungsanleitung
BEA
BEA FALCON Bedienungsanleitung
BEA
BEA IXIO-DP1 Bedienungsanleitung
BEA
BEA IXIO-ST Bedienungsanleitung
BEA
BEA LZR RS300 Bedienungsanleitung
BEA
BEA Eagle HM Bedienungsanleitung
