Belden Hirschmann MACH104-PoEP Series Bedienungsanleitung

Installation MACH104-PoEP

Release

11/2013

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Workgroup Switch

MACH104-PoEP Full Gigabit Family

V.24USB

Aufkleber MAC-Adresse

FAULT

x y

MACH104

V.24USB

Aufkleber MAC-Adresse

FAULT

21 22

x y

MACH104

MACH104-16TX-PoEP+2X...

MACH104-16TX-PoEP+2X-R...

MACH104-16TX-PoEP+2X-E...

MACH104-16TX-PoEP...

MACH104-16TX-PoEP-R...

MACH104-16TX-PoEP-E...

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation 039 782-001-06-1113 –

21.11.2013

Installation MACH104-PoEP

Release

11/2013 3

Contents

Safety instructions 5

About this manual 10

Legend 10

1 Description 11

1.1 General device description 11

1.2 Device name and product code 12

1.3 Device variants available 12

1.4 Device views 13

1.4.1 Front view 13

1.4.2 Rear view 14

1.5 Supply voltage 14

1.5.1 MACH104-16TX-PoEP...

MACH104-16TX-PoEP+2X... 15

1.5.2 MACH104-16TX-PoEP-R...

MACH104-16TX-PoEP+2X-R... 15

1.5.3 MACH104-16TX-PoEP-E...

MACH104-16TX-PoEP+2X-E... 15

1.6 Ethernet ports 15

1.6.1 10/100/1000 Mbit/s twisted pair port 15

1.6.2 100 Mbit/s F/O port 16

1.6.3 1000 Mbit/s F/O port 16

1.6.4 10-Gbit/s F/O port 17

1.6.5 PoE ports 17

1.6.6 Combo ports 18

1.6.7 SFP/XFP transceiver 18

1.7 Display elements 19

1.7.1 Device state 19

1.7.2 Port state 20

1.8 Management interfaces 21

1.8.1 V.24 interface (external management) 21

1.8.2 USB interface 22

1.9 Signal contact 22

4Installation MACH104-PoEP

Release

11/2013

2 Installation 23

2.1 Unpacking and checking the content of the package 23

2.2 Installing SFP/XFP transceivers (optional) 24

2.3 MACH104-16TX-PoEP-E...,

MACH104-16TX-PoEP+2X-E...:

Wiring and assembling the operating voltage 24

2.4 Wiring and assembling the signal contact 25

2.5 Installing the device and grounding 26

2.5.1 Selecting the assembly location 26

2.5.2 Mounting on a flat surface 27

2.5.3 Mounting in a switch cabinet 27

2.5.4 Mounting on the wall 28

2.5.5 Grounding the device 29

2.6 Operating the device 29

2.7 Connecting network cables 30

3 Basic set-up 31

3.1 Default settings 31

4 Maintenance and service 33

5 Deinstallation 34

5.1 Removing the device 34

5.2 Deinstalling the SFP/XFP transceivers 34

6 Technical data 35

A Further Support 44

Installation MACH104-PoEP

Release

11/2013 5

Safety instructions

Certified usage

Only use the device for application cases that are described in the

Hirschmann product information, including this manual. Only operate the

device according to the technical specifications.

Supply voltage

The supply voltage is electrically isolated from the housing.

Solely connect a supply voltage that corresponds to the type plate of

your device.

This applies to the following device variants only:

MACH104-16TX-PoEP-E...

MACH104-16TX-PoEP+2X-E...

Install an input fuse with a maximum rating of 10 A, characteristic B,

into the supply line to the voltage input.

Use conductors with a minimum cross-section of 1 mm2for the supply

line to the voltage input.

Exclusively connect SELV circuits with the voltage restrictions in

accordance with IEC/EN 60950-1 to the supply voltage connections.

Ensure that the connected supply voltage complies with the

requirements according to IEEE 802.3af or IEEE 802.3at.

Use undamaged parts.

The device does not contain any service components. Internal fuses

are only triggered if there is a fault in the device. If the device is not

functioning correctly, or if it is damaged, switch off the voltage supply

and return the device to the plant for inspection.

Only switch on the device when the housing is closed.

Only use connection cables that are permitted for the specified

temperature range.

Relevant for North America:

Only use copper wire/conductors of class 1, 60/75°C or 75°C.

Make sure that the disconnecting device is easily accessible so that

the MACH104-PoEP device can be disconnected from the mains

voltage.

If you disconnect the device from the mains voltage using

- the plug in the socket

- an on/off switch

it must be easily accessible.

This applies to the following device variants only:

MACH104-16TX-PoEP-R...

MACH104-16TX-PoEP+2X-R...

Pull both non-heating plugs to disconnect the device from mains

voltage.

6Installation MACH104-PoEP

Release

11/2013

Shielding ground

The shielding ground of the connectable twisted pair lines is connected to

the protective conductor connection via the front panel.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

The device is grounded via the voltage supply socket.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

inside of the device.

Verify that the electrical installation meets locally or nationally

applicable safety regulations.

Keep the ventilation slits free to ensure good air circulation.

Make sure there is at least 3.94 inches (10 cm) of space in front of the

ventilation slits of the housing.

The device must be installed in the horizontal or upright position, either

as a table unit in the switch cabinet (see figure 6) or on the wall (see

figure 7).

In order to fix the device to a concrete wall choose screws with a

thread major diameter of at least 5 mm.

Environment

Only operate the device at the specified ambient temperature

(temperature of the surrounding air at a distance of up to 5 cm from the

device) and at the specified relative humidity.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

Installation MACH104-PoEP

Release

11/2013 7

General safety instructions

This device is operated by electricity. You must follow precisely the

prescribed safety requirements for the voltage connections in this

document.

See “Supply voltage” on page 5.

Non-observance of these safety instructions can cause material damage

and/or injuries.

Only appropriately qualified personnel should work on this device or in

its vicinity. The personnel must be thoroughly familiar with all the

warnings and maintenance procedures outlined in this operating

manual.

The proper and safe operation of this device depends on proper

handling during transportation, proper storage and assembly, and

conscientious operation and maintenance procedures.

Never start operation with damaged components.

Only use the devices in accordance with this manual. In particular,

observe all warnings and safety-related information.

Any work that may be required on the electrical installation may only

be carried out by personnel trained for this purpose.

Two or more devices configured with the same IP address can cause

unpredictable operation of your network.

Install and maintain a process that assigns a unique IP address to

every device in the network.

Please note that products recommended as accessories may have

characteristics that do not fully correspond to those of the

corresponding product. This may limit their possible usage in the

overall system.

Only connect the PoE connections to PoE-supplier devices whose

data connections are located in the interior of the building and are

specified as SELV circuits.

Note: LED or LASER components in compliance with IEC 60825-1

(2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

National and international safety regulations

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

8Installation MACH104-PoEP

Release

11/2013

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The product can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Reliability: EN 60950-1

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

FCC note

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Device variant Directive

MACH104-16TX-PoEP...

MACH104-16TX-PoEP+2X...

MACH104-16TX-PoEP-R...

MACH104-16TX-PoEP+2X-R...

MACH104-16TX-PoEP-E...

MACH104-16TX-PoEP+2X-E...

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on

the restriction of the use of certain hazardous substances in

electrical and electronic equipment.

2004/108/EC (EMC)

Directive of the European Parliament and the council for

standardizing the regulations of member states with regard to

electromagnetic compatibility.

MACH104-16TX-PoEP...

MACH104-16TX-PoEP+2X...

MACH104-16TX-PoEP-R...

MACH104-16TX-PoEP+2X-R...

2006/95/EC

Directive of the European Parliament and the council for

standardizing the regulations of member states with regard to

electrical equipment to be used within specific voltage

ranges.

Installation MACH104-PoEP

Release

11/2013 9

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate high

frequencies, and if it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a living area can also cause interference, and in this case

the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation MACH104-PoEP

Release

11/2013

About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The following manuals are available as PDF files on the CD/DVD supplied:

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

Reference manual for the graphical user interface

Command Line Interface user manual

The Industrial HiVision Network Management Software provides you with

additional options for smooth configuration and monitoring:

ActiveX control for SCADA integration

Auto-topology discovery

Browser interface

Client/server structure

Event handling

Event log

Simultaneous configuration of multiple devices

Graphical user interface with network layout

SNMP/OPC gateway.

Legend

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

Andere Handbücher für Hirschmann MACH104-PoEP Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden Hirschmann HiOS-2S Bedienungsanleitung

Belden

Belden Hirschmann RS20 U Series Bedienungsanleitung

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Bedienungsanleitung

Belden

Belden Hirschmann RED25 Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Grass Valley K-Frame Anleitung zur Verwendung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden Hirschmann DRAGON MACH Series Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Hirschmann MACH104 Series Benutzerhandbuch

Belden

Belden grass valley GV FABRIC Bedienungsanleitung

Belden

Belden Hirschmann MACH1000 Series Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden grass valley KULA AV Bedienungsanleitung

Belden

Belden Hirschmann Rail Switch Power Lite Bedienungsanleitung

Belden

Belden Hirschmann MACH1040 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS24 Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER II 8TX Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 4000 Series Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden Grass Valley Kayenne Beilage

Belden

Belden HIRSCHMANN Octopus II Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung