Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Bedienungsanleitung

Installation SPIDER-SL

Release

05/2022

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Rail Switch

SPIDER Standard Line

2022-05-25 Installation SPIDER-SL

Release

05/2022

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation SPIDER-SL

Release

05/2022 3

Contents

Important information 5

Safety instructions 7

About this Manual 13

Key 14

1 Description 15

1.1 General device description 15

1.2 Device name and product code 16

1.3 Device view 17

1.3.1 Front view 17

1.4 Power supply 19

1.4.1 Supply voltage with the characteristic value HH 19

1.4.2 Supply voltage with characteristic value HK 19

1.5 Ethernet ports 19

1.5.1 10/100/1000 Mbit/s twisted pair port 19

1.5.2 10/100 Mbit/s twisted pair port 20

1.5.3 100/1000 Mbit/s F/O port 20

1.5.4 100 Mbit/s F/O port 20

1.6 Pin assignments 21

1.7 Display elements 21

1.7.1 Device status 21

1.7.2 Port status 22

2 Installation 23

2.1 Checking the package contents 23

2.2 Mounting the device 23

2.2.1 Installing the device onto the DIN rail 24

2.2.2 Mounting on a flat surface 25

2.3 Installing an SFP transceiver (optional) 26

2.4 Connecting the terminal block 26

2.4.1 Connecting the 3-pin terminal block (device variants

with characteristic value HH) 27

4Installation SPIDER-SL

Release

05/2022

2.4.2 Connecting the 3-pin voltage terminal with spring

(device variants with the characteristic value HK) 28

2.5 Operating the device 29

2.6 Connecting data cables 29

3 Monitoring the ambient air temperature 30

4 Maintenance and service 31

5Disassembly 32

5.1 Removing an SFP transceiver (optional) 32

5.2 Removing the device 33

6 Technical data 34

A Further support 41

Installation SPIDER-SL

Release

05/2022 5

Important information

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes may

appear throughout this documentation or on the device. These notes warn of

potential hazards or call attention to information that clarifies or simplifies a

procedure.

Symbol explanation

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

If this symbol is displayed in addition to a safety instruction of the

type “Danger” or “Warning”, it means that there is a danger of

electric shock and failure to observe the instructions will

inevitably result in injury.

This symbol indicates the danger of hot surfaces on the device.

In connection with safety instructions, non-observance of the

instructions will inevitably result in injuries.

DANGER

DANGER draws attention to an immediately dangerous situation, which will

inevitably result in a serious or fatal accident if not observed.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

6Installation SPIDER-SL

Release

05/2022

NOTICE

NOTICE provides information about procedures that do not involve the risk

of injury.

Installation SPIDER-SL

Release

05/2022 7

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 34.

Connect to the product only components suitable for the requirements

of the specific application case.

Installation site requirements

Operate the device only at the specified ambient temperature

(temperature of the ambient air at a distance of 5 cm (2 in) from the

device) and at the specified relative humidity.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Install the device in a switch cabinet or on a wall.

8Installation SPIDER-SL

Release

05/2022

Strain relief

Note: If the strain relief is insufficient, there is a potential risk of torsion,

contact problems and creeping interruptions.

Relieve the connection points of cables and lines from mechanical

stress.

Design strain reliefs in such a way that they help prevent any

mechanical damage to cables, wires or conductors caused by external

influences or their own weight.

To help prevent damage to device connections, connectors and

cables, follow the instructions for proper installation in accordance with

DIN VDE 0100-520:2013-06, sections 522.6, 522.7 and 522.13.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 34.

Mount the device in the vertical position.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

The device is grounded by a 3-pin terminal block.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.5 mm² (AWG20).

Installation SPIDER-SL

Release

05/2022 9

Shielding ground

The shielding ground of the connectable twisted pair cables is connected

to the ground connection as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

Supply voltage

The supply voltage is only connected with the ground connection via

protective elements.

General requirements for connecting electrical wires

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

The switched voltage complies with the requirements for a safety extra-low voltage (SELV)

according to IEC 60950-1 or ES1 according to IEC/EN 62368-1.

Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Requirements for connecting the supply voltage

The following requirements apply without restrictions:

The supply voltage corresponds to the voltage specified on the type plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is

clear which disconnecting device belongs to which power supply cable.

The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² (AWG20).

The cross-section of the ground conductor is the same size as or bigger than the cross-

section of the power supply cables.

The following requirements apply alternatively:

Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) according to IEC 60950-1 or ES1 + PS2 according to IEC/EN 62368-1.

Alternative 2 All of the following requirements are complied with:

The power supply complies with the requirements for a safety extra-low

voltage (SELV) according to IEC 60950-1 or ES1 according to IEC/

EN 62368-1.

A back-up fuse suitable for DC voltage is located in the plus conductor of

the power supply.

The minus conductor is on ground potential. Otherwise, a back-up fuse is

also located in the minus conductor.

Regarding the properties of this back-up fuse:

See “General technical data” on page 34.

Alternative 3 Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

10 Installation SPIDER-SL

Release

05/2022

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

You find the EU conformity declaration as PDF file for downloading on the

Internet at: https://www.doc.hirschmann.com/certificates.html

The device can be used in industrial environments.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55032

You find more information on technical standards here:

“Technical data” on page 34

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden Grass Valley Kayenne Beilage

Belden

Belden Grass Valley K-Frame Anleitung zur Verwendung

Belden

Belden HIRSCHMANN HiOS-2A Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 100 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN SPIDER II Bedienungsanleitung

Belden

Belden grass valley MASTERPIECE 12G-SDI Bedienungsanleitung

Belden

Belden Hirschmann MACH102 Series Bedienungsanleitung

Belden

Belden Hirschmann RED25 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN RSP20 Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH4002-48+4G Bedienungsanleitung

Belden

Belden ThinkLogical TLX12 Bedienungsanleitung

Belden

Belden Telecast Fiber Systems THOR-SLG Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden Hirschmann DRAGON MACH Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER Standard Line Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 4000 Series Bedienungsanleitung

Belden

Belden Hirschmann MACH104-PoEP Series Bedienungsanleitung

Belden

Belden HIRSCHMANN GRS105 Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Bedienungsanleitung

Belden

Belden Hirschmann GREYHOUND GRS1042 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch