Belden Hirschmann SPIDER-SL-20-01T1S29999SZ9HHHH Bedienungsanleitung

Installation SPIDER-SL

Release

01/2020

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Rail Switch

SPIDER Standard Line

2020-01-20 Installation SPIDER-SL

Release

01/2020

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation SPIDER-SL

Release

01/2020 3

Contents

Safety instructions 5

About this Manual 10

Legend 11

1 Description 12

1.1 General device description 12

1.2 Device name and product code 13

1.3 Device view 14

1.3.1 Front view 14

1.4 Power supply 16

1.4.1 Supply voltage with the characteristic value HH 16

1.4.2 Supply voltage with characteristic value HK 16

1.5 Ethernet ports 16

1.5.1 10/100/1000 Mbit/s twisted pair port 16

1.5.2 10/100 Mbit/s twisted pair port 17

1.5.3 100/1000 Mbit/s F/O port 17

1.5.4 100 Mbit/s F/O port 17

1.6 Pin assignments 18

1.7 Display elements 18

1.7.1 Device state 18

1.7.2 Port status 19

2 Installation 20

2.1 Checking the package contents 20

2.2 Mounting the device 21

2.2.1 Installing the device onto the DIN rail 21

2.2.2 Mounting on a flat surface 22

2.3 Installing an SFP transceiver (optional) 23

2.4 Wiring the terminal block for the supply voltage and the

grounding 24

2.4.1 Connecting the 3-pin terminal block (device variants

with characteristic value HH) 25

4Installation SPIDER-SL

Release

01/2020

2.4.2 Connecting the 3-pin voltage terminal with spring

(device variants with the characteristic value HK) 26

2.5 Operating the device 27

2.6 Connecting data cables 27

3 Monitoring the ambient air temperature 28

4 Maintenance and service 29

5Disassembly 30

5.1 Removing an SFP transceiver (optional) 30

5.2 Removing the device 31

6 Technical data 32

A Further support 38

Installation SPIDER-SL

Release

01/2020 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 32.

Connect to the product only components suitable for the requirements

of the specific application case.

Installation site requirements

Install the device in a fire enclosure according to EN 60950-1.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 32.

Mount the device in the vertical position.

6Installation SPIDER-SL

Release

01/2020

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

The device is grounded by a 3-pin terminal block.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.5 mm² (AWG20).

Shielding ground

The shielding ground of the connectable twisted pair cables is connected

to the ground connection as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation SPIDER-SL

Release

01/2020 7

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

Supply voltage

The supply voltage is only connected with the ground connection via

protective elements.

General requirements for connecting electrical wires

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Requirements for connecting the supply voltage

The following requirements apply without restrictions:

The supply voltage corresponds to the voltage specified on the type plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is

clear which disconnecting device belongs to which power supply cable.

The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² (AWG20).

The cross-section of the ground conductor is the same size as or bigger than the cross-

section of the power supply cables.

The following requirements apply alternatively:

Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 All of the following requirements are complied with:

The power supply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

A fuse suitable for DC voltage is located in the plus conductor of the power

supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 32.

Alternative 3 Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

8Installation SPIDER-SL

Release

01/2020

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55032

You find more information on technical standards here:

“Technical data” on page 32

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Installation SPIDER-SL

Release

01/2020 9

FCC note

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

SPIDER-SL

U.S. Contact Information

Belden – St. Louis

1 N. Brentwood Blvd. 15th Floor

St. Louis, Missouri 63105, United States

Phone: 314.854.8000

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation SPIDER-SL

Release

01/2020

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

Documentation mentioned in the “User Manual Installation” that is not

supplied with your device as a printout can be found as PDF files for

downloading on the Internet at: https://www.doc.hirschmann.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Hirschmann MACH1000 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN SPIDER II 16TX EEC Bedienungsanleitung

Belden

Belden grass valley MASTERPIECE 12G-SDI Bedienungsanleitung

Belden

Belden Hirschmann GREYHOUND GRS1042 Bedienungsanleitung

Belden

Belden Hirschmann Rail Switch Power Lite Bedienungsanleitung

Belden

Belden Hirschmann SPIDER II 8TX Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Bedienungsanleitung

Belden

Belden Hirschmann MACH104-PoEP Series Bedienungsanleitung

Belden

Belden HIRSCHMANN PTN-CSM310-A Bedienungsanleitung

Belden

Belden Hirschmann SPIDER 8TX EEC Bedienungsanleitung

Belden

Belden grass valley GV FABRIC Bedienungsanleitung

Belden

Belden ThinkLogical TLX12 Bedienungsanleitung

Belden

Belden HIRSCHMANN SPIDER II Bedienungsanleitung

Belden

Belden HIRSCHMANN GRS105 Bedienungsanleitung

Belden

Belden HIRSCHMANN HiOS-2A Bedienungsanleitung

Belden

Belden Hirschmann MACH104 Series Benutzerhandbuch

Belden

Belden lumberg automation 0960 IOL 3816-001 Bedienungsanleitung

Belden

Belden HIRSCHMANN BRS20 Bedienungsanleitung

Belden

Belden Hirschmann HiOS-2S Bedienungsanleitung

Belden

Belden Hirschmann DRAGON MACH Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch