BGS technic 8482 Bedienungsanleitung

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8482

Ball Joint Tool for BMW 3 Series

A professional quality tool designed for easy removal and insertion of press fit control arm ball joints

Suitable for use on BMW 3 series (E36) models

1. Press Frame Assembly

2. Removal Shell

3. Installation Shell

4. Drive Screw with Thrust Bearing

5. Spindle Support

6. Support

7. Removal Bush

8. Installation Bush

WARNING

Before starting work under a car always ensure that it is adequately supported by axle stands or

ramps.

Chock wheels and ensure that the hand brake is firmly applied.

Always work in a well ventilated area.

Always use approved eye protection especially when working under vehicles.

Ensure that tools are correctly mounted.

Always use workshop manual for detailed instructions.

Do not over tighten or use undue force as this can cause damage to both tool and component.

Always lubricate screw thread.

Do not use an impact wrench with this tool

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Extraction Insertion

A = Bush

1. Securely support the vehicle and follow workshop manual instructions to access the ball joint.

Mark the position of the ball joint to ensure the new ball joint is correctly installed.

2. Ensure that the screw threads (4) are clean, in good condition and freely lubricated each time

before use.

3. To remove the old ball joint assemble the tool as shown, using the bright plated shells (2) &

(7). Note ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to

slowly turn the drive screw (4) to extract the ball joint from the control arm.

4. Clean the lower face & bore of the control arm using a wire brush to remove any rust. Do not

apply any grease to the bore or the ball joint taper.

5. To install the new ball joint assemble the tool as shown, using the shells (8) & (3). Note:

ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to slowly turn

the drive screw (4) to insert the ball joint into the control arm. Always lubricate the screw

threads before using the tool.

Inhaltsverzeichnis

Andere BGS technic Werkzeuge Handbücher

BGS technic

BGS technic 1124 Bedienungsanleitung

BGS technic

BGS technic 9565 Bedienungsanleitung

BGS technic

BGS technic 8846 Bedienungsanleitung

BGS technic

BGS technic 9451 Bedienungsanleitung

BGS technic

BGS technic 1480 Bedienungsanleitung

BGS technic

BGS technic 8492 Bedienungsanleitung

BGS technic

BGS technic 3140 Bedienungsanleitung

BGS technic

BGS technic 9992 Bedienungsanleitung

BGS technic

BGS technic 9246 Bedienungsanleitung

BGS technic

BGS technic 9276 Bedienungsanleitung

BGS technic

BGS technic 62604 Bedienungsanleitung

BGS technic

BGS technic 7744 Bedienungsanleitung

BGS technic

BGS technic 3201 Bedienungsanleitung

BGS technic

BGS technic 9009 Bedienungsanleitung

BGS technic

BGS technic 9690 Bedienungsanleitung

BGS technic

BGS technic 9862 Bedienungsanleitung

BGS technic

BGS technic 70008 Bedienungsanleitung

BGS technic

BGS technic 9101 Bedienungsanleitung

BGS technic

BGS technic BGS 8857 Bedienungsanleitung

BGS technic

BGS technic 566 Bedienungsanleitung

BGS technic

BGS technic 3515 Bedienungsanleitung

BGS technic

BGS technic 8867 Bedienungsanleitung

BGS technic

BGS technic 8527 Bedienungsanleitung

BGS technic

BGS technic 74428 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung