BGS technic 8717 Bedienungsanleitung

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8717

SAND BLAST CABINET

Please read instructions before operation the blasting system.

Failure to follow these instructions could result in operator injury and damaged to the sand blasting

cabinet.

The sand blast cabinet will produce a powerful flow of abrasive particles.

To avoid personal injury and property damage study this manual thoroughly before assembling,

operating or servicing this sand blast cabinet. This sand blast cabinet is designed for cleaning,

polishing and finishing with dry abrasive ONLY, such as glass bead or plastic granule abrasives.

The finishes can vary from course to fine according to the sizing of the glass bead on delicate parts.

Start out with minimal air pressure to avoid unnecessary excessive abrasion.

Do Notice this sand blasting system is equipped with a 3-prong grounded plug for protection against

shock. When connecting your unit obey all applicable electrical and safety codes. The blasting system

should be only plugged into an adequately grounded 3-prong receptacle. Abrasive media is very

slippery and should be cleaned up immediately to avoid possible operator injury.

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

MOUNTING

Step1

Step2

Connect front panel (2), rear panel (3), right

panel (4R), left panel (4L) and screw up all of the

screws.

Connect the base to the four legs (7A) and (7B)

Then put screen (23) in the cabinet.

Step3

Step4

Secure the glove (21) with the gloves clamp (22)

onto the front panel as illustrated.

Connect the lamp clamp as illustrated.

Step5

Step6

Assemble the filter. Push the fluorescent lamp (26) forward into the

lamp clamp (6). Then put the electric cord

outside the hole through (4L). Use screw nut

whitch is enclosed in the cord to secure.

Then combinet with the circuid inside the wire

connection and screw up tight at left panel.

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Step7

Assemble the blast gun.

Step8

Step9

After you complete the assembly of the SBC.

Then you shall assemble the transparent to lid

(1). Please lock up the movable leaf above the

rear panel (3).

Upon locking up the movable leaf.

Put the transparent top lid under the moveable

leaf to lock up the handle first. Then put item

(22) through the holes on the moveable leaf.

Step 10

Open up the top lid and connect the positioning

chain.

Please connect the two ends of the chain with

the screw and nut as illustrated.

This prevents falling down of the top lid when it

is opened.

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

OPERATE

1. Place the sand blast cabinet near a 230V/60Hz AC electrical outlet. Make sure the receptacle will

accept the 3 -prong plug so that the unit will be properly grounded. Also make sure to check the

power source is adequate for use with this blast system.

2. Attach the air supply line from a compressor capable of maintaining 5 CFM at 80 PSI to the inlet

connector found on the right side of the cabinet. Because of variation in air supply systems, the air

inlet coupling is not provided. Use the particular fitting that is compatible with your air supply

system. Do not operate the blasting system at over 100 psi.

3. Check the air supply line fittings and hose attachments to the rear of the gun. Also make sure the

media supply hose is attached lightly on the nipple on the underside of the gun.

4. Place no more than 10 pounds of abrasive media into the center of the cabinet. Excessive

amounts will create clouded cabinet conditions, blow by media through the exhaust or sluggish

and ineffective blasting performance.

5. With the air supply connected, all fittings and joints not leaking and the unit is plugged in. You are

ready to test the blasting system. Now follow these steps for start up operation.

6. Place the part in the cabinet. Always close and latch the lid after placing the part in the cabinet

prior to blasting. Severe injury to the skin and eyes may result from exposure to the blast stream.

After pulling your hands into the gloves grasp the gun and depress the trigger. This should begin

the blasting flow. If no flow is seen you may need to clear the tube by covering the gun nozzle

momentarily.

7. Now you may begin finishing the part. You should move the blast stream continuously over the

part in an even and circular motion. The flow should not be too hard or concentrated to avoid

undesirable peening.

PARTS

Transparent Top Lid

RF LR Leg

1/4” Hose Clamp

Top Lid Position Chain

Screw 1/4x3/8"

Glove Clamp

Screw

Screw 5/32x3/8"

Glove

Nut

Nut 5/32"

Self Drilling Screw

Movable Leaf

Nut

Screw

Plastic Screw

Sanding Gun

Air cleaner

Front Panel

Nozzle

Filter

Rear Panel

Air Supply Hose

Anchor Plate

Right Panel

Plastic Suction Hose

Lamp

Left Panel

Steel Suction Hose

Feed thru

Base

Air Hose Connector

Wire Connector Box

Lamp Clamp

Washer

AC-AC Adaptor

LF RR Leg

Air Supply Connector

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

MAINTENACE

Disconnect power and air before any maintenance!

All blasting system is prone to plugging or wear because of the abrasive material used and the

applications.

The following items should be checked for wear as indicated:

Plugged Conditions

The blast nozzle may become plugged from moist media.

Try dislodging the media with a drill bit held in your hand. You need to get rid of the most media if the

abrasive pick-up hose appears plugged cover the gun tip and force the air back through this hose.

Dust may fly up when you do this so make sure the lid is down!

Wear conditions

This is usually noted when an excessive amount of dust appears in the cabinet.

Dust will occur if:

The abrasive blasting media is worn out If it has lost its granular or spherical appearance or has a

lot of debris from the parts being blasted and mixed in replace it.

This is usually noticed when the abrasive media that exits the nozzle looks like a smoke cloud

coming instead of a stream.

The air outlet vent is lugged or air flow out is blocked. Cleaning this vent should help reduce dust

in the cabinet. This gun parts may wear may wear out.

This is usually evident when the blast pattern is too wide and ineffective, simply replace nozzle or

orifice.

To replace the transparent PVC board

At the bottom of parts No.1 transparent top lid ,there is a 0.5mm replaceable transparent PVC board,

when at work, if the transparent PVC board is getting unclear, it may be replaced with a new one to

avoid affecting the sight during work.

0.5 mm PVC board

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

CE-Erklärung

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected] www.bgstechnic.com

EU-KONFORMITÄTSERKLÄRUNG

EC DECLARATION OF CONFORMITY

DÉCLARATION„CE“ DECONFORMITE

DECLARATIONDE CONFORMIDADUE

Wir erklären in alleiniger Verantwortung, dass die Bauart des Produktes:

We declare that the following designated product:

Nous déclarons sous propre responsabilité que ce produit:

Declaramos bajo nuestra sola responsabilidad que este producto:

folgenden einschlägigen Bestimmungen entspricht:

complies with the requirements of the:

est en conformité avec les réglementations ci-dessous:

esta conforme a las normas:

Angewandte Normen:

,GHQWL¿FDWLRQRIUHJXODWLRQVVWDQGDUGV

Norme appliquée:

Normas aplicadas:

ppa.

Frank Schottke, Prokurist

BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen

Wermelskirchen, den

Druckluft-Sandstrahlkabine ( BGS Art. 8717 )

Air Sandblasting Cabinet

Cabine de sablage à air comprimé

Cabina de arenado neumática

Machinery Directive 2006/42/EC

LVD Directive 2014/35/EU

EMC Directive 2014/30/EU

EN ISO 12100:2010, EN ISO 13849-1:2015

EN 60204-1:2006+A1:2009+AC:2010

EN 1248:2001/A1:2009, EN 61000-6-1:2007

EN 61000-6-3:2007+A1:2011

EN 61000-6-1:2007, EN 61000-3-3:2013

EN 61000-6-3:2007+A1:2011

EN 61000-3-2:2014

Verification: IT051252XH170801 / XH-SBC90

Report: BCTC-FY17070476E / BCTC-FY170704768S

BCTC-FY170704768S

23.04.2018

Andere Handbücher für 8717

Andere BGS technic Werkzeuge Handbücher

BGS technic

BGS technic BGS 8515 Bedienungsanleitung

BGS technic

BGS technic 8589 Bedienungsanleitung

BGS technic

BGS technic 9688 Bedienungsanleitung

BGS technic

BGS technic 9451 Bedienungsanleitung

BGS technic

BGS technic 1768 Bedienungsanleitung

BGS technic

BGS technic 9224-1 Bedienungsanleitung

BGS technic

BGS technic 9497 Bedienungsanleitung

BGS technic

BGS technic 8848 Bedienungsanleitung

BGS technic

BGS technic 149 Bedienungsanleitung

BGS technic

BGS technic 8729 Bedienungsanleitung

BGS technic

BGS technic BGS 67302 Bedienungsanleitung

BGS technic

BGS technic 1230 Bedienungsanleitung

BGS technic

BGS technic BGS 9686 Bedienungsanleitung

BGS technic

BGS technic 3060 Bedienungsanleitung

BGS technic

BGS technic 9309 Bedienungsanleitung

BGS technic

BGS technic 8978 Bedienungsanleitung

BGS technic

BGS technic 62637 Bedienungsanleitung

BGS technic

BGS technic 1890 Bedienungsanleitung

BGS technic

BGS technic 70345 Bedienungsanleitung

BGS technic

BGS technic 7753 Bedienungsanleitung

BGS technic

BGS technic BGS 18087 Bedienungsanleitung

BGS technic

BGS technic 8522 Bedienungsanleitung

BGS technic

BGS technic 9754 Bedienungsanleitung

BGS technic

BGS technic 9637 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung