BLADEZ ION 150 Handbuch

Bladez ION 150

Open the 4 screws to remove the deck

Troubleshooting Procedures on ION-150

BEFORE RETURNING UNITS TO THE STORE, PLEASE KINDLY CHECK THE FOLLOWING:

1. Check to make sure that the front wheel rotates freely and rear wheel rotates with little resistance when push by hand.

2. Check the tightness of the belt – refer to the end of this guide for checking belt tightness.

If you have problem push start the unit initially or after the first run, begin by checking throttle as shown in page 5.

Troubleshooting (Note: Always take full charge before attempting to work on the scooter)

Symptoms Causes Solutions

Unit will not run even with a push

start

Loose connector

Bad Motor

Faulty Throttle cable

Visually check all the plugs are properly

connected and no broken wires, refer to wire

connection at the end of this guide

Refer to the check motor at the end of this

guide

See check throttle illustration at the end of this

guide

Unit won’t take recharge Bad wall AC outlet

Faulty Charger

Faulty Battery

Use Volt-ohm meter to detect the presence of

AC voltage at the wall outlet

See check charger illustration at the very end

of this guide

Individual battery reading should be around

12.6 or above after fully charged. Replace the

entire set of battery if voltage is below 10.5V.

The polarity difference between the two

batteries should not be more than 0.3V

Faulty Control Board

Replace Control Board

Unit run a short range Faulty Battery

Tight Belt - If the belt is adjusted too tight, it

will create a high resistance on the wheel and it

drains out the battery sooner

Tire pressure is low or tire inner tube is puncture

Individual battery reading should be around

12.6 or above after fully charged. Replace the

entire set of battery if voltage is below 10.5V.

The polarity difference between the two

batteries should not be more than 0.3V

Loose up the belt, see check belt tightness

illustration for troubleshooting

Add air to the tire or replace tire if puncture,

refer to the owner’s manual for replacing tire

Front steering feel loose or bolt

and nuts fall off

Handlebar installed incorrectly

Please make sure that the bolts and nuts are

placed correctly as shown

Check Charger

ION 150 comes with 100-130VAC 50/60Hz 0.2A input, 29V/1A output charger as shown. With the voltmeter set to read DC voltage

and have the probes place on top of the charger plug as shown, you should get a reading of ~ 27 ± 10V. If you get ~ 0 V reading, then

the charger is bad.

Charger comes with the unit

Check Charger Base

Place red probe on the charger pot and the black probe to the charger connector (black wire) as shown, the reading should be ~ 0.2 Ω.

Do the same checking to the same connector (red wire), the reading should be over 1 kΩ. If open circuit (OL) is detected, the charger

base is bad.

Check Throttle cable

1. Disconnect the throttle cable from the controller and place a flat head screw driver or any metal piece in between the

connectors of the throttle cable (controller side), then push to turn the rear wheel towards the front as shown. If the unit starts

to run with an initial push and will stop when the screw drive is pulled out, then the throttle cable (Part No. 70238) needs to be

replaced. Otherwise, the control board (Part No. 70269) needs to be replaced.

Unplug the throttle female connector from male connector on the Controller Board, place the probes on contacts as shown and with Ω

select from the voltmeter. The meter should read OL (open circuit) when throttle is off and should read ~ 0.5 Ωwith the throttle lever

fully depressed. If OL (open circuit) is found when fully depressed, throttle cable or lever is bad.

Check brake cable

Unplug the brake male connector from the female connector on the Controller Board, place the probes on contacts as shown and with

Ωselect from the voltmeter. The meter should read OL (open circuit) when brake is off and should read ~ 0.5 - 1 Ωwith the brake

lever fully depressed. If OL (open circuit) is found when fully depressed, the brake cable or lever is bad.

Check belt tightness

1. Raise the rear wheel and clamp the amp-meter on the red battery cable as shown, then depress throttle lever and turn the rear

wheel to start the scooter. Make sure that you measure the DC current (not AC ~ ), the reading would prefer to be around 1.9 –

2.3 A. Any reading below or above these ranges would consider as too loose or too tight respectively.

2. Visually inspecting the tightness of the belt by grabing the belt with your fingers in between the rear sprocket and the motor

and twist it over so that the belt is vertical. If the belt is twisted to and pass the vertical direction, it is set too loose. Otherwise,

it is too tight if you can’t even twist it to 45° angle.

ION 150 Wire Connections

Battery:

Andere Handbücher für ION 150

Inhaltsverzeichnis

Andere BLADEZ Roller Handbücher

BLADEZ

BLADEZ Travel Mate DKS280 Bedienungsanleitung

BLADEZ

BLADEZ PB-SE802 Bedienungsanleitung

BLADEZ

BLADEZ XTR-HD Bedienungsanleitung

BLADEZ

BLADEZ XTR Street PB-SM1806 Bedienungsanleitung

BLADEZ

BLADEZ PB-SM1816 Bedienungsanleitung

BLADEZ

BLADEZ PB-SM804SA Bedienungsanleitung

BLADEZ

BLADEZ XTR-COMP IIPB-SM 818 Bedienungsanleitung

BLADEZ

BLADEZ DKS320 EXECUTIVE Bedienungsanleitung

BLADEZ

BLADEZ Travel Mate DKS280 Bedienungsanleitung

BLADEZ

BLADEZ Sport DKS200 Bedienungsanleitung

BLADEZ

BLADEZ PRESIDENT Bedienungsanleitung

BLADEZ

BLADEZ DKS500 AMBASSADOR Bedienungsanleitung

BLADEZ

BLADEZ ION 450 Bedienungsanleitung

BLADEZ

BLADEZ MOBY XS PB-SE830PF Bedienungsanleitung

BLADEZ

BLADEZ E-LITE 250 Bedienungsanleitung

BLADEZ

BLADEZ ION 150 Bedienungsanleitung

BLADEZ

BLADEZ PB-SM 817 Bedienungsanleitung

BLADEZ

BLADEZ MOBY X Bedienungsanleitung

Beliebte Roller Handbücher anderer Marken

TEKTRO

TEKTRO CHEETAH Bedienungsanleitung

PLAYTIVE

PLAYTIVE AS-2448 Bedienungsanleitung

Ebinger

Ebinger DONKEY XL Bedienungsanleitung

Flyer

Flyer Mountain Benutzerhandbuch

BackCountry eBikes

BackCountry eBikes Storm Bedienungsanleitung

equipmed

equipmed FreeRoam II Bedienungsanleitung

Yoto

Yoto Lion Bedienungsanleitung

WESTHILL BIKES

WESTHILL BIKES LINK Bedienungsanleitung

BAnff

BAnff eProdigy series Bedienungsanleitung

Winther

Winther 475 Bedienungsanleitung

Jetson

Jetson JBZL17 Bedienungsanleitung

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung

Carrera

Carrera impel Bedienungsanleitung

Afikim

Afikim Superlight SL-3 Bedienungsanleitung

CareCo

CareCo ZOOM Bedienungsanleitung

Douglas

Douglas Vespa G.S. Bedienungsanleitung

Gazelle

Gazelle with BOSCH System Bedienungsanleitung

Wisper

Wisper 806fe Bedienungsanleitung