Blizzard Lighting Lo-Pro CSI Bedienungsanleitung

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

Lo-Pro CSI™ 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The Lo-Pro CSI™ 5

Features 5

DMX Quick Reference 5

The Lo-Pro CSI™ Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of Stiletto’s 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Fixture Linking (Master/Slave Mode) 9

Mounting/Rigging 9

4. Operating Adjustments 10

The Control Panel 10

Control Panel Menu Structure 11

DMX Channel Settings 11

View Fixture Info (Hours, Version#) 11

Dimmer Delay Settings 11

DMX, Auto & Sound Active Modes 11

Manual Settings 11

Troubleshooting 12

5. Appendix 13

A Quick DMX Lesson 13

Keeping Your Lo-Pro CSI™ As Good As New 14

Returns (Gasp!) 14

Shipping Issues 14

Tech Specs 15

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x Lo-Pro CSI™

• An Ever-So-Handy Power Cord

• One really classy DMX cable

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on your purchase of the amazing Lo-Pro CSI™. With a name like Lo-Pro

CSI™, it is denitely worth some investigation! Now that you’ve got your Lo-Pro CSI™

(or hopefully, CSI’s!)

, you should carefully unpack the box and check the contents to en-

sure that all parts are present and in good condition. If anything looks as if it has been

damaged in transit, notify the shipper immediately and keep the packing material for

inspection. Again, please save the carton and all packing materials. If a xture must be

returned to the factory, it is important that the xture be returned in the original factory

box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run o a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the

xture you receive is suitable for your local power supply. See the label on the xture or

refer to the xture’s specications chart for more information. A xture’s listed current

rating is its average current draw under normal conditions. Check the xture or device

carefully to make sure that if a voltage selection switch exists that it is set to the correct

line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied

does not match the voltage indicated on the voltage selector switch. All xtures

must be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardlighting.

com and open a support ticket. We’ll be happy to help, honest.

Blizzard Lighting

N16 W23390 Stoneridge Dr. Ste E

Waukesha, WI 53188 USA

www.blizzardlighting.com

414-395-8365

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any

errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the

right to update the existing document or to create a new document to correct any errors

or omissions at any time. You can download the latest version of this document from

www.blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Henry 2/17/2015 J. Thomas 4/9/2015

Page 4

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please open a support ticket at www.

blizzardlighting.com/tickets.

Page 5

2. MEET THE LO-PRO CSI™

MAIN FEATURES

• 36x high output, 3-watt ~365nm UV LED

• Full on UV intensity + 2 unique pixel patterns

• Variable electronic strobe and dimmer

• Built-in auto programs via master/slave

• Built-in sound active programs

• Standalone, master/slave, auto, sound active modes

• Easy 1/2/3/4/5-channel DMX control

• 15° Beam angle

• Lightweight and Compact (It kept its New Years’ resolution!)

• 4-button LED control panel for easy programming

• Power outlet for xture linking

• Two-piece mounting yoke allows exibility in positioning

DMX Quick Reference (1/2/3/4/5-Channel Modes)

Channel 1.001 2.001 3.001 4.001 5.001

1Dimmer UV Intensity Dimmer Dimmer Dimmer

2-- UV Intensity UV Intensity Strobe Strobe

3-- -- UV Intensity UV Intensity UV Intensity

4-- -- -- UV Intensity UV Intensity

5-- -- -- -- Color Temp

Page 6

Figure 1: The Lo-Pro CSI™ Pin-Up Picture

36x3w ~365nm UV LEDs

Figure 2: The Rear Connections

PowerCon™

Compatible In/Out

LED Display

Touring-

grade

compact

shell

Two-piece

mounting

yoke

4-button Control Panel

Safety Cable Attachment Holes

DMX 3-pin In/Out

Tightening

Knob

Page 7

3. SETUP

Fuse Replacement

CAUTION! The Lo-Pro Flux™ utilizes a high-output switch-mode power

supply with an internal fuse. Under normal operating conditions, the fuse

should not require replacement. The fuse is eld replaceable, however it

is an advanced procedure suited to qualied individuals. Should your Lo-

Pro Flux™ fuse require replacement, please contact Blizzard Lighting for

instructions, or to return your unit for service.

Connecting A Bunch of Lo-Pro Flux™ Fixtures

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more xtures set to sync in master/

slave operating mode. The combined number of channels required by all

the xtures on a serial data link determines the number of xtures the

data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 xtures on one serial data link without the

use of a DMX optically-isolated splitter may result in deterioration of the

digital DMX signal. The maximum recommended cable-run distance is 500

meters (1640 ft). The maximum recommended number of xtures on a

serial data link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-

grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but note

that they cannot transmit DMX data as reliably over long distances. In

any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR

connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the x-

ture’s chassis ground. Grounding the common can cause a ground

loop, and your xture may perform erratically. Test cables with an

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.

They are widely available over the internet and from specialty retailers If you’d like to build your own, the

chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male

(Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)

on the controller.

Step 2: Connect the female connector of the

DMX cable to the rst xture’s male connec-

tor (input). Note: It doesn’t matter which

xture address is the rst one connected.

We recommend connecting the xtures in

terms of their proximity to the controller,

rather than connecting the lowest xture

number rst, and so on.

Step 3: Connect other xtures in the chain

from output to input as above. Place a DMX

terminator on the output of the nal xture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the

DMX cable to the output (female) 3 pin connector of

the rst xture.

2. Connect the end of the cable coming from the

rst xture which will have a (female) 3 pin connec-

tor to the input connector of the next xture con-

sisting of a (male) 3 pin connector. Then, proceed

to connect from the output as stated above to the

input of the following xture and so on.

A quick note: Often,

the setup for Master-

Slave and Standalone

operation requires that

the rst xture in the

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.

Secondarily, the xtures

that follow may also re-

quire a slave setting.

Check the “Operating Adjustments” section in this manual for com-

plete instructions for this type of setup and conguration.

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

xture using a suitable “C” or “O” type clamp. The clamp should be

rated to hold at least 10x the xture’s weight to ensure structural sta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly “rated” rigging is used when mounting xtures overhead.

Adjust the angle of the xture by loosening both knobs and tilting the

xture. After nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp

replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the xture will be exposed to rain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and dierent modes possible with the Lo-Pro CSI™ are

accessed by using the control panel on the front of the xture. There

are 4 control buttons below the LED display which allow you to navi-

gate through the various control panel menus.

Button Function

<MENU>

<UP>

<DOWN>

<ENTER>

Used to access the menu or to return to a previous menu option.

Scrolls through menu options in ascending order.

Scrolls through menu options in descending order.

Used to select and store the current menu or option within a menu.

Access control panel functions using the four panel buttons located

directly underneath the LED Display.

The Control Panel LED Display shows the menu items you select from

the menu map on page #11. When a menu function is selected, the

display will show immediately the rst available option for the selected

menu function. To select a menu item, press <ENTER>.

Use the <UP> and <DOWN> buttons to navigate the menu map

and menu options. Press the <ENTER> button to access the menu

function currently displayed or to enable a menu option. To return to

the previous option or menu without changing the value, press the

<MENU> button.

Inhaltsverzeichnis

Andere Blizzard Lighting Beleuchtungsausrüstung Handbücher

Blizzard Lighting

Blizzard Lighting Flurry Spot Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting PixelStorm COB Mini Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ProPar V12 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent 90 Beam Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting SkyBox EXA Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Pocket Rocket Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughPar V12 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting KRYO.MIX CMY Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting G70 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Metro Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughStick 5 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Sketch Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent 90 Beam Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting HUSH PAR Theatrik Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting mikrokassette Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting COLORISE Exa Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck CSI Xtreme Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting infinipix cyclone Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting SNAKE EYES Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting PixlStik Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting HUSH PAR Infiniwhite 500 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting The Puck 3NX Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting REANIMATOR Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting SPOTMAN Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung