Blomberg KNM4563EI Bedienungsanleitung

Full-integrated

Frost Free Combi Fridge Freezer

Operating instructions

KNM4563Ei

1 EN

Please read these instructions first before using your

appliance

Thank you for choosing a Blomberg appliance.

Please take some time to read this user manual before using your appliance,

to ensure you know how to safely operate the controls and functions.

Carefully follow all unpacking and installation instructions to ensure the

appliance is correctly connected and fitted prior to use.

Please write your product model and serial number on the last page of this

user manual, and store in a safe location close to the appliance for easy

future reference.

This user manual may also be applicable for several other models.

Differences between models will be listed.

If you have any questions or concerns, please call our contact centre or find

help and information online at www.blomberguk.com.

Explanation of symbols used throughout this User Manual

- The terminal in the plug is marked with the symbol.

- The freezer compartment is marked with the symbol.

WARNING!

In order to ensure a normal operation of your refrigerating appliance, which uses

a completely environmentally friendly refrigerant the R600a (flammable only

under certain conditions) you must observe the following rules:

•

Do not hinder the free circulation of the air around the appliance.

Do not use mechanical devices in order to accelerate the defrosting,

others than the ones recommended by the manufacturer.

Do not destroy the refrigerating circuit.

Do not use electric appliances inside the food keeping compartment, other

than those that might have been recommended by the manufacturer.

-Important information or useful usage tips.

-Warning against dangerous conditions for life and property.

-Warning against electric voltage.

-Symbol for waste electrical and electronic equipment.

1 Your refrigerator 3

2 Warnings 4

Electrical Requirements .....................5

Warning! This Appliance Must Be

Earthed .............................................5

Energy Saving Tips ............................6

Compliance with WEEE Directive and

Disposing of the Waste Product: .......6

Compliance with RoHS Directive:.......6

Package information ..........................6

3 Installation 7

Points to be considered when re-

transporting your refrigerator .............7

Before operating your refrigerator ......7

Disposing of the packaging ...............7

Disposing of your old refrigerator .......8

Placing and Installation ......................8

Installation Instructions ......................8

4 Before operating 11

Final Check .....................................11

5 Using your refrigerator 12

Control Panel ..................................12

Storing Frozen Food ........................12

Freezing Fresh Food ........................13

Making Ice Cubes ............................13

Defrosting ........................................13

6 Maintenance and cleaning 14

7 Do’s and Don’ts 15

9Guarantee details 20

Replacing the interior light bulb

...........9

Problem solving................................16

CONTENTS

Electric connection ............................7

Reversing the doors.............

................9

Transportation instructions.................6

10 How to obtain service 22

8 Installation of high

levelling foot 17

3 EN

1Your refrigerator

1. Control panel

2. Interior light

3. Adjustable shelves

4. Wine rack

5. Defrost water collection channel

6. Crisper cover

7. Crisper

C Figures that take place in this instruction manual are schematic and may not

correspond exactly with your product. If the subject parts are not included in

the product you have purchased, then it is valid for other models.

8. Ice bank

9. Freezer compartment drawers

10. Adjustable door shelves

11. Eggs holder

12. Bottle shelf

13. Freezer fan

Congratulations on your choice of a Blomberg quality Appliance which has

been designed to give you service for many years.

2 Warnings

• DO NOT connect your appliance to

the electricity supply until all packing

and transit protectors have been

removed.

• Leave to stand for at least 4 hours

before switching on to allow

compressor oil to settle if transported

horizontally.

• If you are discarding an old

refrigerator with a lock or latch fitted

to the door, disable the lock/latch,

ensure that it is left in a safe

condition to prevent the entrapment

of young children.

• This fridge/freezer must only be used

for its intended purpose i.e. the

storing and freezing of edible

foodstuff.

• Do not dispose of the appliance on a

fire. At Blomberg, the care and

protection of our environment is an

ongoing commitment. This appliance

which is among the latest range

introduced is particularly

environment friendly. Your appliance

contains non CFC / HFC natural

substances in the cooling system

(Called R600a) and in the insulation

(Called cyclopentane) which are

potentially flammable if exposed to

fire. Therefore, take care not to

damage, the cooling circuit/pipes of

the appliance in transportation and in

use. In case of damage do not

expose the appliance to fire or

potential ignition source and

immediately ventilate the room

where the appliance is situated.

• We suggest you contact your local

authority for disposal information and

facilities available.

•See Installation Instructions on page

8 for information on suitable location.

•To obtain the best possible

performance and trouble free

operation from your appliance it is

very important to carefully read

these instructions.

• On delivery, check to make sure that

the product is not damaged and

that all the parts and accessories

are in perfect condition.

•Ensure that the plug remains readily

accessible. Do not use multiple

adapter or extension cable.

• Failure to observe these

instructions may invalidate your right

to free service during the guarantee

period.

•Keep ventilation openings, in the

appliance enclosure or in the built-in

structure, clear of obstruction.

•Do not use mechanical devices

or other means to accelerate the

defrosting process, other than

those recommended by the

manufacturer.

•Do not damage the refrigerant

circuit.

•Do not use electrical appliances

inside the food storage

compartments of the appliance,

unless they are of the type

recommended by the manufacturer.

• We suggest you keep these

instructions in a safe place for easy

reference.

•This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

•Children should be supervised to

ensure that they do not play with

the appliance.

Do not forget to refit the fuse cover.

In the event of losing the fuse cover the

plug must not be used until a

replacement fuse cover has been

fitted. Colour of the replacement fuse

cover must be the same colour as that

visible on the pin face of the plug. Fuse

covers are available from any good

electrical store.

Important! Fitting A Different Plug

As the colours of the wires in the

mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug

proceed as follows (see diagram):

1. Connect the green-yellow or green

(Earth) wire to the terminal in the

plug marked ‘E’ or with the symbol

or coloured green and yellow or

green.

2. Connect the blue (Neutral) wire to

the terminal in the plug marked ‘N’

or coloured black.

3. Connect the brown (Live) wire to the

terminal in the plug marked ‘L’ or

coloured red.

4. With alternative plugs a 13 A fuse

must be fitted either in the plug or

adaptor or in the main fuse box. If in

doubt contact a qualified electrician.

FITTED WITH

BS 1362 13A FUSE ALWAYS

FIT BS 1362 REPLACEMENT

CARTRIDGE FUSE

GREEN &

YELLOW

GREEN

BLUE

BLACK

BROWN

RED

22 mm.

6 mm.

6 mm. 32 mm.

12 mm.

FUSE

CORD GRIP

Electrical Requirements

Before you insert the plug into the wall

socket make sure that the voltage and

the frequency shown on the rating plate

inside the appliance corresponds to

your electricity supply.

Rating label is on the left hand side of

fridge inner liner.

We recommend that this appliance be

connected to the mains supply via a

suitable switched and fused socket.

The appliance must be positioned so

that the plug is accessible.

WARNING: When positioning the

appliance ensure the supply cord is not

trapped or damaged.

Should the mains lead of the appliance

become damaged or should it need

replacing at any time, it must be

replaced by a special purpose made

mains lead which can only be obtained

from a Blomberg Authorised Service

Agent.

Warning! This Appliance Must

Be Earthed

If the fitted moulded plug is not suitable

for your socket, then the plug should be

cut off and an appropriate plug fitted.

Destroy the old plug which is cut off as

a plug with bared cord could cause a

shock hazard if inserted into a socket

elsewhere in the house.

The moulded plug on this appliance

incorporates a 13 A fuse. Should the

fuse need to be replaced an ASTABEAB

approved BS 1362 fuse of the same

rating must be used.

Energy Saving Tips

1. Ensure your appliance is installed in

a well ventilated area.

2. Ensure the time between buying

chilled/frozen food and placing them

in your appliance is kept at

minimum, particularly in summer. We

recommend you use a cool bag or a

special carrier bag to carry frozen

food.

3. Do not leave the door (s) of your

appliance open longer than

necessary and ensure they are

closed properly after each opening.

4. Defrost frozen food in the fridge, so

that frozen food acts as an ice pack

to assist cooling in fridge.

Compliance with WEEE

Directive and Disposing of

the Waste Product:

This product complies with

EU WEEE Directive

(2012/19/EU). This product

bears a classification symbol

for waste electrical and

electronic equipment

(WEEE). This product has

been manufactured with

high quality parts and

materials which can be reused and are

suitable for recycling. Do not dispose

of the waste product with normal

domestic and other wastes at the end

of its service life. Take it to the

collection center for the recycling of

electrical and electronic equipment.

Please consult your local authorities to

learn about these collection centers.

Compliance with RoHS

Directive:

The product you have purchased

complies with EU RoHS Directive

(2011/65/EU). It does not contain

harmful and prohibited materials

specified in the Directive.

Package information

Packaging materials of the product

are manufactured from recyclable

materials in accordance with our

National Environment Regulations. Do

not dispose of the packaging

materials together with the domestic

or other wastes. Take them to the

packaging material collection points

designated by the local authorities.

TRANSPORTATION

INSTRUCTIONS

1. The appliance should be transported

only in a vertical upright position. The

packing as supplied must be intact

during transportation.

2. If during the course of transport the

appliance has to be transported

horizontally, it must only be laid on its

right hand side when standing in the

front of the appliance. After bringing

it to upright position, it must not be

operated for at least 4 hours to allow

the system to settle.

3. Failure to comply with the

above instructions could result in

damage occurring to the appliance.

The manufacturer will not be held

responsible if these instructions are

disregarded.

4. The appliance must be protected

against rain, moisture and other

atmospheric influences.

5. When positioning your appliance

take care not to damage your flooring,

pipes, wall coverings etc. Do not move

the appliance by pulling by the door or

handle.

6. Empty any water in the drain

tray before moving. See section

‘Defrosting’ and "Maintenance and

cleaning" for further information.

7. Make sure that the defrost water

pipe at the back of the product is fixed

to the plastic evaporating pan on the

top of the compressor, to avoid defrost

water spillage on the floor.

3 Installation

B Please remember that the

manufacturer shall not be held liable if

the information given in the instruction

manual is not observed.

Points to be considered

when re-transporting your

refrigerator

Please do not forget…

Every recycled material is an

indispensable source for the nature

and for our national resources.

If you wish to contribute to recycling

the packaging materials, you can get

further information from the

environmental bodies or local

authorities.

Before operating your

refrigerator

Before starting to use your

refrigerator check the following:

4. You will hear a noise as the

compressor starts up. The liquid and

gases sealed within the refrigeration

system may also give rise to noise,

even if the compressor is not running

and this is quite normal.

5. Front edges of the refrigerator may

feel warm. This is normal. These

areas are designed to be warm to

avoid condensation.

Electric connection

Connect your product to a grounded

socket which is being protected by a

fuse with the appropriate capacity.

Important:

• The connection must be in

compliance with national regulations.

• The power cable plug must be easily

accessible after installation.

• The specified voltage must be equal

to your mains voltage.

•Extension cables and multi way plugs

must not be used for connection.

B A damaged power cable must be

replaced by a qualified electrician.

B Product must not be operated before

it is repaired! There is danger of

electric shock!

WARNING: Do not locate extension

sockets or charging transformers/power

supplies or Lithium-Iron battery

operated products adjacent to the

compressor as they could overheat.

1. Your refrigerator must be

emptied and cleaned prior to any

transportation.

2. Shelves, accessories, crisper and

etc. in your refrigerator must be

fastened securely by adhesive tape

against any jolt before repackaging.

3. Packaging must be adequate,

and the ru les of transportation

printed on the package must

be followed.

1. Is the interior of the refrigerator dry

and can the air circulate freely in the

rear of it?

2. Clean the interior of the refrigerator

as recommended in the

"Maintenance and cleaning”

section.

3. Plug the refrigerator into the wall

outlet. When the fridge door is

open, the fridge compartment

interior light will come on.

Disposing of the packaging

The packing materials may be dangerous

for children. Keep the packing materials

out of the reach

of childre n or dispose of

them by classifying them in accordance

with the waste instructions. Do not

dispose of them along with the normal

household waste.

The packing of your refrigerator is

produced from recyclable materials.

Disposing of your old

refrigerator

Dispose of your old refrigerator

without giving any harm to the

environment.

•You may consult your authorised

dealer or waste collection center of

your municipality about the disposal

of your refrigerator.

4. Place your refrigerator on an even

floor surface to prevent jolts.

5. Do not keep your refrigerator in

ambient temperatures under 10°C.

Before disposing of your refrigerator,

cut off the electric plug and, if there

are any locks on the door, make them

inoperable in order to protect children

against any danger.

Placing and Installation

installed is not wide enough for the

refrigerator to pass through, then

carefully remove the doors of your

refrigerator and pass it sideways

through the door.

 Install your refrigerator to a place that

allows ease of use.

 Keep your refrigerator away from

heat sources, humid places and

direct sunlight.

 There must be appropriate air

ventilation around your refrigerator

in order to achieve an efficient

operation. If the refrigerator is to be

placed in a recess in the wall, there

must be at least 5 cm distance with

the ceiling and at least 5 cm with the

wall. If the floor is covered with

a carpet, your product must be

elevated 2.5 cm from the floor.

1. The space in the room where the

appliance is installed must not be

smaller than 10 cubic metres.

2. See Installation-Diagram for detailed

Installation Instructions.

3. This appliance has been designed to

operate in ambient temperatures up

to 38 degrees C (100 degrees F) and

is equipped with Freezer Guard

technology which ensures that even

if the ambient temperature falls to

-15°C, frozen food in the freezer

does not thaw thanks to this. So, you

may then install your appliance in a

garage or an unheated room without

having to worry about frozen food in

the freezer being spoilt.

IMPORTANT: Care must be taken

while cleaning / carrying the appliance

to avoid touching the bottom of the

condenser metal wires at the back of

the appliance as you might injure your

fingers and hands.

Do not attempt to sit or stand on top of

your appliance as it is not designed for

such use. You could injure yourself or

damage the appliance.

IMPORTANT: Make sure that

mains cable is not caught under the

appliance during and after carrying

/ moving the appliance, to avoid

the mains cable becoming cut or

damaged.

Do not allow children to play with the

appliance or tamper with the controls.

Blomberg declines to accept any

liability should the instructions not be

followed.

Installation Instructions

A If the entrance door of the room

where the refrigerator will be

Replacing the interior light

bulb

To change the Bulb/LED used for

illumination of your refrigerator, call your

Authorised Service. The lamp(s) used in

this appliance is not suitable for

household room illumination. The

intended purpose of this lamp is to

assist the user to place foodstuffs in the

refrigerator/freezer in a safe and

comfortable way.

The lamps used in

this appliance have to withstand

extreme physical conditions such as

temperatures below -20°C.

Reversing the doors

Top door

1. Unscrew top hinge (1).

2. Carefully remove the top door (2).

3. Unscrew lower hinge (3).

4. Remove plastic plugs (7 & 8).

5. Refit top hinge (1) as lower hinge (16)

on the left hand side.

6. Replace top door (17).

7. Refit lower hinge (3) as top hinge (18)

on the left hand side.

Lower door

1. Unscrew top hinge (4).

2. Carefully remove the lower door (5).

3. Unscrew lower hinge (6).

4. Remove plastic plugs (9 & 10).

5. Refit hinge (4) as lower hinge (11) on the

left hand side.

6. Replace lower door (12).

7. Refit lower hinge (6) as top hinge (13) on

the left hand side.

Refit plastic plugs (7, 8, 9 & 10) into the

screw holes on the right hand side (14,

15, 19 & 20).

However at low ambient temperatures

mentioned above, fridge contents are

likely to freeze, so check and consume

food in the fridge accordingly. When

the ambient temperature returns to

normal, you may change the knob

setting to suit your needs. If the

ambient temperature is below 0°C,

the food in the fridge compartment will

freeze. So, we recommend you don’t

use the fridge compartment in such

low ambient conditions. You can

continue using the freezer

compartment as usual.

4. Do not place the appliance near

cookers, radiators or in direct sunlight

as this will cause your appliance to

work harder. If installed next to a

source of heat or freezer, maintain the

following minimum side clearances:

From Cookers 50 mm (2”)

From Radiators 300 mm (12”)

From Freezers 25 mm (1”)

5. Refer to "Maintenance and cleaning"

section to prepare your appliance for

use.

6. A special receptacle is supplied to

store the mains plug during transit.

The receptacle is fixed at the back of

the cabinet, on the side of the

compressor (see diagram). Gently

remove the plug from the receptacle.

Never pull the mains cord, you may

damage the appliance. In the case of

transportation, ensure you locate the

plug in the receptacle provided to

avoid transit damage.

Inhaltsverzeichnis

Andere Blomberg Kühlschrank Handbücher

Blomberg

Blomberg DSM 9630 A++ Bedienungsanleitung

Blomberg

Blomberg BRFD2650SS Bedienungsanleitung

Blomberg

Blomberg SSM 1550 Bedienungsanleitung

Blomberg

Blomberg DSM 1510 Bedienungsanleitung

Blomberg

Blomberg DSM 1510 Bedienungsanleitung

Blomberg

Blomberg SSM 1550 i Bedienungsanleitung

Blomberg

Blomberg KGM 9680 Bedienungsanleitung

Blomberg

Blomberg DNE9840A+ Bedienungsanleitung

Blomberg

Blomberg FNT 9670 XT Bedienungsanleitung

Blomberg

Blomberg FNT4550 Bedienungsanleitung

Blomberg

Blomberg BRFB1045 Series Bedienungsanleitung

Blomberg

Blomberg BRFB1044WH Bedienungsanleitung

Blomberg

Blomberg DND 9977 P Bedienungsanleitung

Blomberg

Blomberg FNT 9672 X Bedienungsanleitung

Blomberg

Blomberg MDND 1880 Bedienungsanleitung

Blomberg

Blomberg BRFB 1042SSN Bedienungsanleitung

Blomberg

Blomberg DSM 1510 Stücklistenhandbuch

Blomberg

Blomberg DND 1972 XD Bedienungsanleitung

Blomberg

Blomberg BRSBS 2130 Bedienungsanleitung

Blomberg

Blomberg KGM4530 Bedienungsanleitung

Blomberg

Blomberg SOM 9651 P Bedienungsanleitung

Blomberg

Blomberg KSM 1650 Bedienungsanleitung

Blomberg

Blomberg BRFB1044SS Bedienungsanleitung

Blomberg

Blomberg KND 9653 A++ Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung