Bosch D9210C Fehlerbehebungshandbuch

Access Control Interface Module

D9210C

en Program Entry Guide

Access Control Interface Module Table of Contents | en 3

Bosch Security Systems, Inc. Program Entry Guide F.01U.201.526 | 02 | 2011.10

Table of Contents

1 Trademarks 4

2 Door Profile 5

3 Strike Profile 9

4EventProfile 12

4.1 Notes 14

5 Program Record Sheets 15

5.1 Profiles 16

5.1.1 Door Profiles 16

5.1.2 Strike Profiles 16

5.1.3 Event Profiles 16

4en | Trademarks Access Control Interface Module

F.01U.201.526 | 02 | 2011.10 Program Entry Guide Bosch Security Systems, Inc.

1 Trademarks

About This Document

This document describes the parameters available to the security panel for programming the

D9210C Access Control Interface. For a description of the theory of operation and the actual

operation of the unit, please refer to the D9210C Operation and Installation Guide (P/N:

F01U215244).

This document follows the organization of the RADXAXS handler in the D5200 Programmer

(for GV3 Series v8.0x, GV2 Series, and G Series Control Panels) or RPS (Remote Programming

Software). Use the ACCESS Control Interface Module Program Record Sheet (P/N:

F01U201528) to record your choices prior to programming the device. Each programming

section, program item, and its page number are listed in the table of contents on the following

page.

Throughout this document, programming prompts are shown in bold italic letters when they

are used in a sentence. For example, Door # is the first programming prompt in the DOOR

PROFILE section of the program. Reference to handlers, modules, categories and sections of

the program are shown in italic, capital letters.

For a more complete understanding of the panel and the D9210C Access Control Interface,

read the following in addition to this program entry guide:

– D9210C Operation and Installation Guide (P/N: F01U215244)

– Security System Owner’s Manual

– Security System User Guide

Other Lettering Conventions used in this document

D6600 Security Receiver and local printer reports are shown in typewriter -style letters. For

example: ACCESS GRANTED indicates the report sent when the Access Control Interface

detects a valid card read.

Generally, words shown in all capital letters with brackets indicate command center displays

and command center keys. For example, [ESC] is a key on the command center. Depending

on the context of the sentence, all capital letters may also indicate a recommended

programming selection.

Reading Bosch Security Systems, Inc. Product Date Codes For Product Date Code

information, refer to the Bosch Security Systems, Inc. Web site at: http://

www.boschsecurity.com/datecodes/.

NOTICE!

References made to the “D9412 Family” will reflect the following product offerings:

D9412GV4, D9412GV3, D9412GV2, D9412G, D9412.

NOTICE!

References made to the “D7412 Family” will reflect the following product offerings:

D7412GV4, D7412GV3, D7412GV2, D7412G, D7412.

Access Control Interface Module Door Profile | en 5

Bosch Security Systems, Inc. Program Entry Guide F.01U.201.526 | 02 | 2011.10

2 Door Profile

This programming category is used to:

– Assign an area which also activates the interface module.

– Assign a point to the door.

– Program the door state to change when the arm state changes.

– Allow for the strike relay to activate upon a fire alarm.

Enter the number of the door you are about to program.

Assign an area to the door controller. This entry allows the D9210C to be polled activating

communication to the panel. This also is the area a user will exit when initiating a Request to

Exit [REX].

1-8 The area assigned to the door controller to which the reader will allow access.

Blank Door controller will not function.

Enter the Command Center number [CC#] which determines the scope of the user ID’s

disarming rights. Areas will disarm on the basis of this Command Center’s scope and the

Authority Level of the user.

Door #

Default: 1

Selections 1-8

NOTICE!

The D9412 Family supports 8 doors; the D7412 Family supports 2 doors.

D# Entry Area #

Default: Blank

Selections: Blank, 1-8

NOTICE!

All SDI devices, regardless of area assigned, will report to Area 1, Account 1 by default upon

SDI failure. If an interface module becomes disconnected, SDI Fail ## and MISSING POINT ###

events will be created.

NOTICE!

9210 NOT READY will appear at this command center when you press the [ENTER] key if the

interface module is not programmed with a D# Entry Area.

D# CC# Scope

Default: Blank

Selections: Blank, 1-8

6en | Door Profile Access Control Interface Module

F.01U.201.526 | 02 | 2011.10 Program Entry Guide Bosch Security Systems, Inc.

1-8 This CC# Scope determines disarming rights. The user’s access level in conjunction with

the CC # Scope will determine which areas will be disarmed.

Blank Only the area assigned to the D# Entry Area will disarm for this door.

Enter the point number that will be assigned to this door. This point cannot be used for any

other point assignments.

1-127, 129-247 The point number assigned to this door. Points 128 and 248 are reserved by

the panel for internal use.

Blank There is no point number assigned to this door.

Enter the interlock point number. This point, when faulted, will prevent the door controller

from allowing access upon a valid ID read or door request.

Do not assign this point as a door point to another door point. You may assign it to another

controller thereby having one interlock point prevent multiple controllers from activating.

1-127, 129-247 The point number assigned to this door. Points 128 and 248 are reserved by

the panel for internal use.

Blank There is no point number assigned to this door.

D# Door Point

Default: Blank

Selections: Blank, 1-127, 129-247

NOTICE!

Door Points must be programmed as Perimeter Points. If a 24 hour point type is required for

the Door Point, you may use a Perimeter Point Type with a Point Response of 9 - C. Also, the

Debounce Count must be set to 4 in Point Assignments.

NOTICE!

When assigning points 1to 8 (panel zones), the end of line resistors must be removed from the

panel

NOTICE!

Do not enable any POPIT points (or OctoPOPIT points) sharing the same point number as the

Door Point. Failure to do so will result in Extra Point trouble conditions upon reboot.

D# Interlock Point

Default: Blank

Selections: Blank, 1-127, 129-247

NOTICE!

The interlock point will be considered in a normal state if it is bypassed swinger bypassed or

forced armed. This will result in normal operation of access even if the door is left open.

Access Control Interface Module Door Profile | en 7

Bosch Security Systems, Inc. Program Entry Guide F.01U.201.526 | 02 | 2011.10

Use this program item to unlock the door (latched shunt and strike) automatically when the

entry area is disarmed. The door will re-lock upon Master or Perimeter Arming the area

Yes When the area assigned in D# Entry Area # is disarmed, the door will be in the Unlocked

state. When that area is armed, the door will return to the Locked state.

No Door state will not be affected by the armed state of the area.

Use this program item to activate the relay for the door strike and shunt the door zone

automatically upon a Fire Alarm. This feature will override a Secure Door state, Locked Door

state, Auto Door, and an Interlock faulted point. The relay will activate for all doors with this

prompt programmed [YES] when a Fire Alarm occurs in any area. Relays that are activated by

Fire Unlock can only be returned to normal through the Command Center using the Door

Control function.

Yes Relay will activate and shunt will be applied for the door contact automatically upon a Fire

Alarm.

No Door will remain in its current mode upon a Fire Alarm.

Use this program item to determine whether the door needs to be physically opened prior to

disarming the area upon a valid access request. The user initiating the access request must

have access levels that allow disarming with ID.

D# Auto Door?

Default: No

Selections: Yes or No

NOTICE!

The Unlocked state cannot be overridden manually.

NOTICE!

Doors that are activated by Fire Unlock must be returned to normal using the Door Control

function on the control center.

D# Fire Unlock?

Default: No

Selections: Yes or No

DANGER!

This will unlock the door regardless of the armed state.

D# Disarm On Open?

Default: No

Selections: Yes or No

8en | Door Profile Access Control Interface Module

F.01U.201.526 | 02 | 2011.10 Program Entry Guide Bosch Security Systems, Inc.

Yes The area will disarm only after the door has been opened for a user with a valid disarm

level.

No The area will disarm whether or not the door has been opened as soon as a user with a

valid disarm level has presented a valid token/card.

Access Control Interface Module Strike Profile | en 9

Bosch Security Systems, Inc. Program Entry Guide F.01U.201.526 | 02 | 2011.10

3 Strike Profile

This programming category is used to create a specific door profile on:

– Strike and shunt times.

– Extending strike and shunt times if a door is left open.

– Resetting the strike when the door opens.

– Programming the interlock point.

Enter the door you are programming.

Enter the amount of time the relay output for the strike will activate to allow a user to open

the door. The strike will activate upon a valid token, Request to Enter [RTE], Request to Exit

[REX], and the Command Center [CYCLE DOOR?] function.

Blank Strike Time is not programmed for this door.

1-240 The strike will activate for the amount of time programmed.

Enter the amount of time that the door point will be shunted to allow a user to open the door

without causing the point to go into Trouble, Alarm or a faulted condition.

Blank TShunt Time is not programmed for this door.

1-240 The shunt will activate for the amount of time programmed.

Enter the amount of time that the buzzer output will activate to notify the user that the strike

has been activated and the door is ready to open. The buzzer will stop as soon as the door is

opened.

Door #

Default: 1

Selections 1-8

D# Strike Time

Default: 10

Selections: 1-240 seconds

D# Shunt Time

Default: 10

Selections: Blank, 1-240

D# Buzz Time

Default: 2

Selections: Blank, 1-240 seconds

NOTICE!

A separate buzzer is required. Many readers have an internal buzzer that is not affected by

Buzz Time.

10 en | Strike Profile Access Control Interface Module

F.01U.201.526 | 02 | 2011.10 Program Entry Guide Bosch Security Systems, Inc.

Blank Buzz Time is not programmed for this door.

1-240 The buzzer will sound for the amount of time programmed.

Enter the amount of time that strike, buzz and shunt activation will be prolonged if a door is

left open and the shunt time expires. At the end of the programmed extend time, the buzzer

will continue to buzz until the door is closed. In addition, if programmed, the point assigned

to the door will indicate a Trouble, Alarm or Fault at the command center.

This program item determines whether the strike will deactivate immediately upon physically

opening the door.

Yes Strike will deactivate when the door is opened after a valid access granted request.

No Strike will remain activated for the amount of the programmed strike time whether door is

opened or closed.

TO REDUCE FALSE ALARMS: We recommend that you maintain this programming item as

defaulted [YES]. This will help prevent the door from “bouncing” open and causing a false

alarm.

Use this program item to disable the strike, but still activate the programmed shunt time upon

a Request to Enter an area.

D# Extend Time

Default: 10

Selections: Blank, 1-30 seconds

NOTICE!

CLOSE DOOR # display on Command Center will not activate if no time (blank) is

programmed.

NOTICE!

Regardless of how the door point is programmed, the system will generate a Trouble Door

Left Open event while the system is disarmed and an Alarm Door Left Open event if the

system is armed and the door is held open beyond Extend Time. Door Closed Restoral events

are generated after the door is held open past Extend Time and the door has returned to

normal.

D# Deact On Open?

Default: No

Selections: Yes or No

NOTICE!

In order for this function to work a point needs to be assigned to the door.

D# RTEShunt Only?

Default: No

Selections: Yes or No

Inhaltsverzeichnis

Andere Bosch Netzwerk-Hardware Handbücher

Bosch

Bosch D8125INV Kurzanleitung

Bosch

Bosch CM-R 19 Bedienungsanleitung

Bosch

Bosch PHANTOM EDGE Bedienungsanleitung

Bosch

Bosch DIVAR IP 7000 2U Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl S67-S3-BK-DI8-M8 Benutzerhandbuch

Bosch

Bosch DX4020-EXP Bedienungsanleitung

Bosch

Bosch VIP X1600 XF Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl XFE01.1-SY-01 Bedienungsanleitung

Bosch

Bosch VIP-X1XF Bedienungsanleitung

Bosch

Bosch VideoJet X10 SN Bedienungsanleitung

Bosch

Bosch VideoJet X10/X20/X40 Bedienungsanleitung

Bosch

Bosch RTS RVON+ Bedienungsanleitung

Bosch

Bosch DIVAR IP 6000 (2U) Bedienungsanleitung

Bosch

Bosch VIP-X1XF Bedienungsanleitung

Bosch

Bosch VIP X1600 M4S Bedienungsanleitung

Bosch

Bosch LTC 4600 Series Bedienungsanleitung

Bosch

Bosch DX2010 Bedienungsanleitung

Bosch

Bosch VIPX1A Bedienungsanleitung

Bosch

Bosch VIP X1 Bedienungsanleitung

Bosch

Bosch D9210B Kurzanleitung

Bosch

Bosch VIP X1 Bedienungsanleitung

Bosch

Bosch VIP X1600 Module Bedienungsanleitung

Bosch

Bosch VideoJet 8008 Bedienungsanleitung

Bosch

Bosch VIP-X1XF-E Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung