Bosch RF3401E Bedienungsanleitung

RF3401E

EN Installation Instructions

Wireless (RF) Point

Transmitter

Bosch Security Systems | 6/03 | 42597E

EN | 2

RF3401E | Installation Instructions | 1.0 Overview

1.0 Overview

The RF3401E Point Transmitter is a magnetic and dry

contact wireless transmitter used for monitoring doors,

windows, or other dry contact devices.

This device is equipped with an internal reed contact for

use with an external magnet assembly and a cover/wall

tamper switch. The point transmitter can accept a dual

EOL resistor supervised dry contact input from an

external device.

Supervision is provided by transmitting a signal to the

receiver every 13 min. if there is no other activity. All

transmissions from the RF3401E send battery status

information.

Table 1: Specifications

Dimensions

(H x W x D)

Transmitter:

76.5 mm x 35 mm x 19 mm

(3 in. x 1.38 in. x 0.75 in.)

Mounting Plate:

76.5 mm x 35 mm x 3.2 mm

(3 in. x 1.38 in. x 0.13 in.)

Magnet:

80 mm x 14 mm x 12 mm

(3.15 in. x 0.55 in. x 0.47 in.)

Operating

Temperature -30°C to +65°C (-22°F to +149°F)

Frequency

Band 433.42 MHz

Maximum RF

Power < 10 mW

Operating

Voltage Supplied by a 3 VDC lithium battery

Battery Life Minimum of five years under normal

operating conditions with the

recommended battery types.

Recommended

Battery Types

Duracell DL 123A,

Energizer EL 123AP, or

Panasonic CR 123A

Compatible

Receivers RF3212E or RF3222E

Compliance CE 0165. This point transmitter

complies with EN 300683,

EN 300220, and 89/336/EEC.

2.0 Specifications

EN | 3

RF3401E | Installation Instructions |

Bosch Security Systems | 6/03 | 42597E

3.0 Mounting

3.1 Mounting Considerations

• The maximum range of the point transmitter, in open

air, is approximately 300 m (984 feet). In normal

residential or commercial applications, it is

recommended the point transmitter be kept within

100 m (328 in.) of the receiver to which it is

assigned.

• Mounting the point transmitter on metal surfaces can

reduce its RF range. Mounting the point transmitter

on ferrous metal (iron or steel) surfaces can affect the

operation of the internal magnetic contact.

• It is recommended the point transmitter be mounted

on the door/window frame and the magnet assembly

be mounted on the moving portion. Note that the

magnet assembly must be mounted within 15 mm

(0.59 in.) of the point transmitter and in an

acceptable orientation as shown in Figure 1.

3.2 Mounting the Transmitter

1. Position the mounting plate over the desired

location. If connecting an external device, position

the mounting plate so the wiring passes through the

wire entrance (see Figure 2).

2. Attach the mounting plate using two flathead screws

(see Figure 2).

When mounting the base, be sure to note

the location of the magnet.

3. If using the wall tamper feature, use a panhead

screw in the wall tamper breakaway (see Figure 2).

4. From the point transmitter bottom (see Figure 3),

remove the wall tamper breakout with a small tool.

Figure 2: Mounting Plate

1 - Magnet

2 - Mounting holes (use two flathead screws)

3 - Wall tamper breakaway (use panhead screw)

4 - Wire entrance

5 - Release tab

Figure 1: Mounting Considerations (shown without

mounting plate or spacer)

1 - Acceptable

2 - Not acceptable

Figure 3: Point Transmitter

The ID label removed to show detail.

1 - Wall tamper breakout area

2 - Wire entrance

Bosch Security Systems | 6/03 | 42597E

EN | 4

RF3401E | Installation Instructions | 3.0 Mounting

Figure 6: Mount for Extra Security

1 - Security screw

Figure 7: Correctly Installed Battery

Cover removed to show detail.

1 - Battery

2 - Tamper switch wires

3 - Wall tamper breakout area

4 - Wire entrance

5 - Release tab

Figure 5: Slide the Point Transmitter onto the

Mounting Plate

5. Tear off the loose portion of the ID label to use in

panel programming (see Section 5.0 Panel

Programming).

6. Depending on which case your transmitter comes

with (see Figure 4), open the transmitter cover by

inserting a small flat-blade screwdriver into the slot

at the end of the transmitter. Then push in with the

screwdriver until the latch opens.

7. Slide the point transmitter over the mounting plate

to lock it into place (see Figure 5). If connecting an

external device, make sure its wiring is pulled

through the wire entrance of the point transmitter as

the point transmitter slides onto the mounting plate.

8. Make the wiring connections for any external

device. Refer to Section 4.0 Setting Up Magnetic or

External Contacts.

Figure 4: Open the Point Transmitter

1 - Insert screwdriver and push here.

2 - Push in.

9. If the installation requires additional security, use an

additional panhead screw to mount the point

transmitter (see Figure 6).

10. Install a recommended battery (see Section 2.0

Specifications). Be sure to observe the proper polarity

(see Figure 7).

11. Close the cover.

12. Release the point transmitter from the base by

disconnecting any external wiring and removing the

security screw (if used). Then press the release tab

(see Figure 7) with a small tool and slide the point

transmitter off the mounting plate.

EN | 5

RF3401E | Installation Instructions |

Bosch Security Systems | 6/03 | 42597E

4.0 Setting Up Magnetic or External Contacts

3.3 Mounting the Magnet Assembly

1. Mount the magnet base using two panhead screws

(see Figure 8).

2. Snap on the magnet cover.

The spacer is optional and should be used

for alignment as needed.

4.0 Setting Up Magnetic or

External Contacts

The RF3401E can monitor its internal reed contact or an

external dry contact.

If using the RF3222E Receiver, the

RF3401E cannot monitor both magnetic and

external contacts simultaneously.

If using the magnet, do not use an external

device.

If using an external device, remove the reed

switch (see Figure 9).

One set of external normally closed (NC) contacts (see

Figure 10) can be monitored. Be sure your panel

supports the intended loop condition.

The contact input is supervised using dual 1.5 kΩand

2.2 kΩ End-of-Line (EOL) resistors. This lets the panel

identify wire tamper conditions (opens or shorts). The

total cable length for the external wiring should not

exceed 6 m (19 feet).

Figure 9: Remove the Reed Switch

1 - Antenna

2 - Reed switch

Figure 10: Typical NC Wiring

1.5 kΩ

2.2 kΩ

1 - Up to 6 m (19 ft.)

2 - Non-polarized

3 - Normally closed (NC) contact

Figure 8: Magnet Assembly

1 - Cover

2 - Base

3 - Spacer

Bosch Security Systems | 6/03 | 42597E

EN | 6

RF3401E | Installation Instructions | 5.0 Panel Programming

Figure 11: ID Number

1 - ID number

2 - Bar code

167770187

5.0 Panel Programming

A two-part ID sticker (see Figure 11) is located on the

housing of the RF3401E. The number on this sticker is

required to program the point transmitter into the

control panel. Refer to your panel's Programming Guide

for programming information on wireless type devices.

PROTÓTIPO DO SELO ANATEL E DA RESOLUÇÃO 365

Código EAN – Modelo RF3401E: (01)07891009341408

Bosch Security Systems

130 Perinton Parkway

Fairport, NY 14450-9199 USA

www.boschsecurity.us

Customer Service: (800) 289-0096

Technical Support: (888) 886-6189

Subject to change | Printed in the USA

42597E

Inhaltsverzeichnis

Andere Bosch Sender Handbücher

Bosch

Bosch RF3401E Bedienungsanleitung

Bosch

Bosch ATX-TRM-304T01 Bedienungsanleitung

Bosch

Bosch RADION RFUN Bedienungsanleitung

Bosch

Bosch RFKF-FB Bedienungsanleitung

Bosch

Bosch ISW-EN1210SK Bedienungsanleitung

Bosch

Bosch CRS-NC-S37L-US Bedienungsanleitung

Bosch

Bosch ISW-EN1265 Bedienungsanleitung

Bosch

Bosch CRS-SB-424FI Bedienungsanleitung

Bosch

Bosch S35 Bedienungsanleitung

Bosch

Bosch CRS-MIYS37-FI Bedienungsanleitung

Bosch

Bosch CRS-SB-423FI Bedienungsanleitung

Bosch

Bosch CRS-NC-S37L Bedienungsanleitung

Bosch

Bosch Security Systems SE2 Series Handbuch

Bosch

Bosch SEC-3402-304 Bedienungsanleitung

Bosch

Bosch ISW-EN1233 Bedienungsanleitung

Bosch

Bosch CRS-RM-905FI Bedienungsanleitung

Bosch

Bosch SE88A-90S-304 Bedienungsanleitung

Bosch

Bosch ISW-EN1215EOL Bedienungsanleitung

Bosch

Bosch CRS-NC-S37E-ACC Bedienungsanleitung

Bosch

Bosch SEC-RFPB60M-433 Bedienungsanleitung

Bosch

Bosch SE-TRM-433T01 Bedienungsanleitung

Bosch

Bosch ISW-EN1210 Handbuch

Bosch

Bosch ISW-EN1261HT Bedienungsanleitung

Bosch

Bosch SEC-3402 Series Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung