Bowflex TreadClimber TC1000 Bedienungsanleitung

BOWFLEX TREADCLIMBER

TC1000-TC3000-TC5000 ASSEMBLY MANUAL

(4 PIECE ASSEMBLY)

USE THIS ASSEMBLY MANUAL WHEN IT SHIPS IN 4 PIECES

(PARTLY DISASSEMBLED) - LIKE THIS DIAGRAM

1Console assembly

2-3 Uprights

4Base

INSTALLING STEPS

Step 6: INSTALLING THE UPRIGHTS

Locate the following for this step:

PARTS:

TreadClimber® Base & Treadle Assembly from Step 5.

One (1) Left Upright Support & Hydraulic Cylinder

One (1) Right Upright Support & Hydraulic Cylinder

HARDWARE:

Two (2) 5/16” x 1” Button Head Screws

On the base assembly screw a 5/16" x 1" button head

screw half way in on the outside of both the right and

left lower upright bracket (see Figure 6-1).

Place the left upright onto the left upright bracket

(see Figure 6-2), so it rests on the button head screw

(see Figure 6-3). Make sure the cylinder bracket is at

the top and pointing to rear.

Repeat this process on the right side.

Figure 6-1

Figure 6-2

Step 7: INSTALLING THE UPRIGHT JUNCTION COVERS AND COSMETIC PLUGS

Locate the following for this step:

PARTS:

TreadClimber® Base & Treadle Assembly from

Step 6.

Two (2) Plastic Upright Junction Covers

HARDWARE:

Four (4) Cosmetic Plugs

Place the plastic upright junction covers onto the

top of left upright support (see Figure 7-1).

Insert the cosmetic plugs (2 per side) into the holes

on the top, inside and outside of the left upright

support (see Figure 7-2).

Repeat this process on the right side.

Figure 6-3

Figure 7-1

Figure 7-2

INSTALLING STEPS

Step 8: INSTALLING THE CONSOLE/ HANDLEBAR ASSEMBLY

Locate the following for this step:

PARTS:

TreadClimber® Base & Treadle Assembly from

Step 7.

Console/Handlebar Assembly

HARDWARE:

Six (6) 5/16” x 1” Button Head Screws

Six (6) 5/16” Flat Washers SAE

TOOLS:

3/16” Hex Key (included)

With the help of another person, carefully lift

the console/handlebar assembly above the

tops of the upright supports. Feed the cable

down the top of the right upright support (see

Figure 8-1 & 8-1A). Make sure cable extends

through the bottom of the right upright.

Slide the brackets on the console/handlebar

assembly into the tops of the upright

supports—both sides at the same time. Be

careful when sliding the console/handlebar

assembly onto the uprights to avoid damaging

the electrical cable.

Attach the upright using (6) 5/16" x 1" button

head screws and (6) 5/16" flat washers SAE (3

per upright). Tighten with the provided 3/16"

hex key (see Figure 8-2).

Pull out the wire connector at the bottom of

the right upright support. Firmly connect the

electrical cable at the bottom of the right

upright support to the cable on the right side

of the base upright bracket (see Figure 8-3).

Figure 8-1

Figure 8-1A

Figure 8-2

Figure 8-3

INSTALLING STEPS

Step 9: SECURING THE CONSOLE/ HANDLEBAR ASSEMBLY

Locate the following for this step:

PARTS:

TreadClimber® Base & Treadle Assembly from

Step 8.

HARDWARE:

Six (6) 5/16” x 1” Button Head Screws NOTE:

Two (2) of the 5/16” x 1” Button Head

screws are already inserted into the bottom of

the right and left upright supports.

Six (6) 5/16” flat washer SAE

TOOLS:

3/16” Hex Key (included)

With the help of another person, carefully lift

the upright and remove the 5/16" x 1" button

head screw at the base of the support on the

right side. Carefully lower the upright on to the

upright bracket base, without damaging the

electrical cable. Repeat on the left side.

Attach the upright using (6) 5/16" x 1" button

head screws and (6) 5/16" flat washers SAE (3

per upright). Tighten with the provided 3/16"

hex key (see Figure 9-1). Repeat this process

on the remaining bracket.

NOTE: Tighten the front (2) screws first (1 per

upright) and then the (4) side screws (two per

outward side of upright). Tightening in this

order will result in a tighter fit.

Figure 9-1

INSTALLING STEPS

Step 10: ATTACHING THE HYDRAULIC CYLINDERS

Locate the following for this step:

PARTS:

TreadClimber® Base & Treadle Assembly from

Step 9.

HARDWARE:

Two (2) 5/16” x 1-1/2” Button Head Screws

Two (2) 5/16” Acorn Nuts

Two (2) 5/16” x 1” Button Head Screws

Two (2) 5/16” Flat Washers

TOOLS:

3/16” Hex Key (included)

9/16” Open End Wrench (included)

First bolt the dial end of the cylinders to the

uprights using (1) 5/16" x 1-1/2" button head

screw and (1) 5/16" acorn nut, per side.

Tighten with the provided 9/16" open end

wrench and 3/16" hex key (see Figure 10-1).

Make sure that the white arrows located on the

Workout Level Setting Dials at the top of the

Hydraulic Cylinders face the rear of the

machine where you can easily see them during

your workout.

Starting on the right side, pull the cylinder down

and place the eyelet on the Cylinder Stud

protruding from the treadles. Attach the

hydraulic cylinder using (1) 5/16" x 1" button

head screws and (1) 5/16" flat washers (see

Figure 10-2).

Repeat this process on the left side.

NOTE: If having difficulty placing hydraulic

cylinder(s) on treadle stud, loosen lower upright

screws, place cylinder on the stud and retighten

the upright screws.

Figure 10-1

Figure 10-2

Step 11: INSPECTING ASSEMBLY

11-1 Remove the protective plastic film from

the console face. Inspect all attachments you

have made thus far and tighten all bolts

securely before proceeding to Step 12.

Andere Handbücher für TreadClimber TC1000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bowflex Fitnessgeräte Handbücher

Bowflex

Bowflex BodyTower Bedienungsanleitung

Bowflex

Bowflex SelectTect BDS1642 Bedienungsanleitung

Bowflex

Bowflex Preacher Curl Attachment Bedienungsanleitung

Bowflex

Bowflex TREADCLIMBER 1000 Bedienungsanleitung

Bowflex

Bowflex Max Trainer M7 Bedienungsanleitung

Bowflex

Bowflex Max Trainer M3 Bedienungsanleitung

Bowflex

Bowflex SelectTech BD552i Bedienungsanleitung

Bowflex

Bowflex LateralX LX3 Bedienungsanleitung

Bowflex

Bowflex Max Trainer M7u Bedienungsanleitung

Bowflex

Bowflex SelectTech ST220 Bedienungsanleitung

Bowflex

Bowflex SelectTech 3.1 Bench Bedienungsanleitung

Bowflex

Bowflex Ultimate 2 Accessory Pack Bedienungsanleitung

Bowflex

Bowflex 1090i Bedienungsanleitung

Bowflex

Bowflex ULTIMATE 2 Bedienungsanleitung

Bowflex

Bowflex SelectTech 840 Kettlebell Bedienungsanleitung

Bowflex

Bowflex TREADCLIMBER 3000 Bedienungsanleitung

Bowflex

Bowflex TC10 Bedienungsanleitung

Bowflex

Bowflex HVT Bedienungsanleitung

Bowflex

Bowflex BXE216 Montage- und Bedienungsanleitung

Bowflex

Bowflex Max Trainer M5 Bedienungsanleitung

Bowflex

Bowflex VersaTrainer Bedienungsanleitung

Bowflex

Bowflex 5.1S Bedienungsanleitung

Bowflex

Bowflex TreadClimber TC20 Bedienungsanleitung

Bowflex

Bowflex SBD1090 Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung