B+K precision 600B Bedienungsanleitung

Model: 600B

SLA Battery Capacity

Analyzer

USER MANUAL

www. .com information@itm.com1.800.561.8187

Safety Summary

The following safety precautions apply to both operating and maintenance personnel and must be

followed during all phases of operation, service, and repair of this instrument.

Before applying power to this instrument:

Read and understand the safety and operational information in this manual.

Apply all the listed safety precautions.

Verify that the voltage selector at the line power cord input is set to the correct line voltage.

Operating the instrument at an incorrect line voltage will void the warranty.

Make all connections to the instrument before applying power.

Do not operate the instrument in ways not specified by this manual or by B&K Precision.

Failure to comply with these precautions or with warnings elsewhere in this manual violates the safety

standards of design, manufacture, and intended use of the instrument. B&K Precision assumes no

liability for a customer’s failure to comply with these requirements.

Category rating

The IEC 61010 standard defines safety category ratings that specify the amount of electrical energy

available and the voltage impulses that may occur on electrical conductors associated with these

category ratings. The category rating is a Roman numeral of I, II, III, or IV. This rating is also accompanied

www. .com information@itm.com1.800.561.8187

by a maximum voltage of the circuit to be tested, which defines the voltage impulses expected and

required insulation clearances. These categories are:

Category I (CAT I): Measurement instruments whose measurement inputs are not intended to be

connected to the mains supply. The voltages in the environment are typically derived from a limited-

energy transformer or a battery.

Category II (CAT II): Measurement instruments whose measurement inputs are meant to be connected

to the mains supply at a standard wall outlet or similar sources. Example measurement environments are

portable tools and household appliances.

Category III (CAT III): Measurement instruments whose measurement inputs are meant to be connected

to the mains installation of a building. Examples are measurements inside a building's circuit breaker

panel or the wiring of permanently-installed motors.

Category IV (CAT IV): Measurement instruments whose measurement inputs are meant to be connected

to the primary power entering a building or other outdoor wiring.

Do not use this instrument in an electrical environment with a higher category rating than what is

specified in this manual for this instrument.

www. .com information@itm.com1.800.561.8187

You must ensure that each accessory you use with this instrument has a category rating equal to or

higher than the instrument's category rating to maintain the instrument's category rating. Failure to do

so will lower the category rating of the measuring system.

Do not operate in an explosive or flammable atmosphere

Do not operate the instrument in the presence of flammable gases or vapors, fumes, or finely-divided

particulates.

The instrument is designed to be used in office-type indoor environments. Do not operate the

instrument

In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or finely-

divided particulates.

In relative humidity conditions outside the instrument's specifications.

In environments where there is a danger of any liquid being spilled on the instrument or where

any liquid can condense on the instrument.

In air temperatures exceeding the specified operating temperatures.

www. .com information@itm.com1.800.561.8187

In atmospheric pressures outside the specified altitude limits or where the surrounding gas is not

air.

In environments with restricted cooling air flow, even if the air temperatures are within

specifications.

In direct sunlight.

This instrument is intended to be used in an indoor pollution degree 2 environment. The operating

temperature range is 0 °C to 40 °C and the operating humidity range is ≤95%relative humidity with no

condensation allowed.

Measurements made by this instrument may be outside specifications if the instrument is used in non-

office-type environments. Such environments may include rapid temperature or humidity changes,

sunlight, vibration and/or mechanical shocks, acoustic noise, electrical noise, strong electric fields, or

strong magnetic fields.

Do not operate instrument if damaged

If the instrument is damaged, appears to be damaged, or if any liquid, chemical, or

other material gets on or inside the instrument, remove the instrument's power cord, remove the

instrument from service, label it as not to be operated, and return the instrument to B&K Precision for

repair. Notify B&K Precision of the nature of any contamination of the instrument.

Clean the instrument only as instructed

www. .com information@itm.com1.800.561.8187

Do not clean the instrument, its switches, or its terminals with contact cleaners, abrasives, lubricants,

solvents, acids/bases, or other such chemicals. Clean the instrument only with a clean dry lint-free cloth

or as instructed in this manual.

Not for critical applications

This instrument is not authorized for use in contact with the human body or for use as a component in a

life-support device or system.

Do not touch live circuits

Instrument covers must not be removed by operating personnel. Component replacement and internal

adjustments must be made by qualified service-trained maintenance personnel who are aware of the

hazards involved when the instrument's covers and shields are removed. Under certain conditions, even

with the power cord removed, dangerous voltages may exist when the covers are removed. To avoid

injuries, always disconnect the power cord from the instrument, disconnect all other connections (for

example, test leads, computer interface cables, etc.), discharge all circuits, and verify there are no

hazardous voltages present on any conductors by measurements with a properly-operating voltage-

sensing device before touching any internal parts. Verify the voltage-sensing device is working properly

before and after making the measurements by testing with known-operating voltage sources and test for

both DC and AC voltages. Do not attempt any service or adjustment unless another person capable of

rendering first aid and resuscitation is present.

www. .com information@itm.com1.800.561.8187

Do not insert any object into an instrument's ventilation openings or other openings.

Servicing

Do not substitute parts that are not approved by B&K Precision or modify this instrument. Return the

instrument to B&K Precision for service and repair to ensure that safety and performance features are

maintained.

For continued safe use of the instrument

Do not place heavy objects on the instrument.

Do not obstruct cooling air flow to the instrument.

Do not place a hot soldering iron on the instrument.

www. .com information@itm.com1.800.561.8187

Table of Contents

Section 1 General Description ....................................................................................................................... 9

1.1 INTRODUCTION.................................................................................................................................... 9

1.2 APPLICATIONS...................................................................................................................................... 9

1.3 SPECIFICATIONS ................................................................................................................................... 9

Section 2 Operation ..................................................................................................................................... 10

2.2 OPERATING PROCEDURE ................................................................................................................... 11

Service Information..................................................................................................................................... 13

Limited One-Year Warranty........................................................................................................................ 14

www. .com information@itm.com1.800.561.8187

Section 1 General Description

1.1 INTRODUCTION

B&K Precision Battery Capacity Analyzer Model 600B measures the % capacity left in a battery. The model 600B supports 12V

storage type lead acid batteries with wide range of Ah capacity. No external power (Main or DC) is required. The unit works on BUT

(Battery Under Test).

1.2 APPLICATIONS

As the information age develops it is likely that the demand for UPS units will increase for use in hospitals, offices, labs etc. It is

expected that the importance of battery maintenance will increase along with increasing demand for UPS.

The 600B can be applicable for Automobile Service Stations, UPS Manufacturing, Maintenance and Field Servicing, QC Department,

Battery Systems in Railways, Telecommunications, Ships / Submarine.

1.3 SPECIFICATIONS

TECHNICAL

1) Capacity Display Range: 0 % to 100 %

2) Max. Input Voltage: 20 V

3) No Load Voltage Indication Accuracy: ± 2 counts

Caution: Do not exceed max. input voltage rating. Doing so may cause fatal damage to the unit.

PHYSICAL

1) Dimensions (WxHxD): 2.91 x 10.44 x 2.12” (74 x 265.1 x 54 mm)

2) Weight: 2.65 lbs. (1.2 Kg.)

NOTE: Specifications and information are subject to change without notice.

www. .com information@itm.com1.800.561.8187

Section 2 Operation

FRONT PANEL CONTROLS

Refer to the Front view of the unit.

1) Ah Range : With this key the user can select the

correct Ah range according to the battery

under test.

2) Ah Select LED: This LED in ON to indicate that the user can

select the Ah range.

3) Ah Setting Saved LED: This LED is ON when the unit locks to a

particular Ah range set by the user.

4) Display Mode: This key selects the display either as

No load voltage or % balance

capacity.

5) Battery Voltage: Indicates that the Battery voltage is being

displayed.

6) Battery Capacity %: This LED is ON when remaining capacity

is being displayed.

7) Load Test: The test starts by pressing this key.

8) Ready/Complete: When this LED is ON and steady, indicates

that the unit is ready to conduct a test.

9) Test In Progress: This LED is ON for approx. 3 sec. when

the battery test is carried out.

10) Reverse Polarity: If the unit is connected to a battery in

reverse polarity this LED will be ON.

11) LED Display Displays either battery voltage or battery

capacity percent.

12) +ve Cable Positive connecting cable with strain relief.

13) –ve Cable Negative connecting cable with strain relief.

www. .com information@itm.com1.800.561.8187

Inhaltsverzeichnis

Andere B+K precision Messgerät Handbücher

B+K precision

B+K precision 875B Bedienungsanleitung

B+K precision

B+K precision 2708B Bedienungsanleitung

B+K precision

B+K precision 4063 Bedienungsanleitung

B+K precision

B+K precision 830C Bedienungsanleitung

B+K precision

B+K precision 2831C Bedienungsanleitung

B+K precision

B+K precision 2640 Bedienungsanleitung

B+K precision

B+K precision 5335B Bedienungsanleitung

B+K precision

B+K precision CP62 Bedienungsanleitung

B+K precision

B+K precision 4070A Bedienungsanleitung

B+K precision

B+K precision DAS240-BAT Bedienungsanleitung

B+K precision

B+K precision 889B Bedienungsanleitung

B+K precision

B+K precision Sefram DAS240 Handbuch

B+K precision

B+K precision 313C Bedienungsanleitung

B+K precision

B+K precision PR65 Series Bedienungsanleitung

B+K precision

B+K precision 177/V-95 Bedienungsanleitung

B+K precision

B+K precision PR-55 Bedienungsanleitung

B+K precision

B+K precision 309 Bedienungsanleitung

B+K precision

B+K precision 302 Bedienungsanleitung

B+K precision

B+K precision 8500B Series Bedienungsanleitung

B+K precision

B+K precision 5335B Bedienungsanleitung

B+K precision

B+K precision 5335B Bedienungsanleitung

B+K precision

B+K precision SEFRAM 7861 Bedienungsanleitung

B+K precision

B+K precision 2652A Bedienungsanleitung

B+K precision

B+K precision 601B Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung