Bradford White RG1PV50S6X19-264 Bedienungsanleitung

238-53846-00A REV 12/19

POWER VENT GAS WATER HEATER

A Spanish language version of these instructions is available by

contacting the company listed on the rating plate.

La version espanola de estas instrucciones se puede obtener al escribirle

a la fabrica cuyo nombre aparece en la placa de especificaciones.

WHAT TO DO IF YOU SMELL GAS

 DO NOT try to light any appliance.

 DO NOT touch any electrical switch; DO NOT use any

phone in your building.

 Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

 If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we recommend this

water heater be installed and serviced by a plumbing professional.

INSTALLATION AND OPERATION

INSTRUCTION MANUAL

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or death.

FOR YOUR SAFETY

DO NOT store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

CONGRATULATIONS!

You have purchased one of the finest water heaters on the market

today!

This installation, operation and instruction manual will explain in

detail the installation and maintenance of your new Power Vented

Gas Water Heater. We strongly recommend that you contact a

plumbing professional for the installation of this water heater.

We require that you carefully read this manual, as well as the

enclosed warranty, and refer to it when questions arise. If you

have any specific questions concerning your warranty, please

consult the plumbing professional from whom your water heater

was purchased. For your records we recommend that you write

the model, serial number and installation date of your water

heater in the maintenance section in the back of this manual.

This manual should be kept with the water heater.

Special Flammable Vapor Ignition Resistant System

This water heater is equipped with a Flammable Vapor Ignition Resistant

System. In the event of improper usage or storage of gasoline or other

flammable materials in the location where the water heater is installed, the

technology will resist ignition of the flammable vapors outside the confines of

the water heater.

The Flammable Vapor Ignition Resistant System features:

 Advanced Flame Arrestor Design;

 Flammable Vapor Sensor;

 Automatic Ignition Device;

 Sight Window to observe operation of pilot and burner.

FOR YOUR SAFETY: Activation of the Flammable Vapor Ignition Resistant

System occurs when flammable vapors are drawn into the water heater and are

combusted. If flammable vapors are detected and/or sensed:

 Do not try to light any appliance.

 Do not touch any electrical switch; Do not use any phone in your

building.

 Leave the premises and immediately call the fire department from a

neighbor’s phone. Follow the fire department’s instructions.

Once the flammable vapor has been evacuated, contact your plumbing

professional or the manufacturer for further instructions. Replacement of a

Flammable Vapor Ignition Resistant System equipped water heater due to a

flammable vapor shutdown is not covered under the terms of the limited

warranty.

TABLE OF CONTENTS

Page

GENERAL INFORMATION ................................................................ 4

INSTALLATION. ................................................................................ 5

Locating The Water Heater ........................................................ 5

Minimum Clearances .................................................................. 8

Venting ........................................................................................ 8

Specifications for 40 Gal (151.4 L) / 50 Gal (189.2 L) / 60 Gal

(227.0 L) ....................................................................................... 12

Vent Pipe Preparation and Joining ........................................... 16

Combustion Air Supply .............................................................. 18

Water Connections ..................................................................... 20

Gas Connections ........................................................................ 23

Electrical Connections ............................................................... 24

Wiring Diagram ........................................................................... 25

GENERAL OPERATION .................................................................... 26

Lighting & Shutdown Instructions ............................................ 27

Thermostat Adjustment ............................................................. 28

Burner Flame Check ................................................................... 29

MAINTENANCE ................................................................................. 29

TROUBLESHOOTING ....................................................................... 34

PARTS DIAGRAM ............................................................................. 37

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING .............................................................................. 38

NOTES .............................................................................................. 39

GENERAL INFORMATION

This gas-fired water heater’s design is certified by CSA International under the

American National Standard Z21.10.1 and CSA 4.1-M, most current editions at

the time of manufacture. This is a category III water heater.

This water heater must be installed in accordance with local codes or, in the

absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest

Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be held liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home. Such

an installation may create a hazardous condition and will nullify the warranty.

DO NOT use this appliance if any external part to the tank has been

submerged in water. You should contact a qualified service technician to

inspect the appliance and to replace any part of the control system including

the combination gas control which has been submerged in water. See the Gas

Connections section of this manual before servicing or replacing a water heater

that has had any external part to the tank submerged in water.

CAUTION

Incorrect operation of this appliance may create a hazard to life

and propert

and will nullif

the warrant

WARNING

Prior to connecting the gas supply line to a gas fired water heater, ensure

that the gas supply line does not have moisture/water or dirt/scale inside

the gas line. Commonly this check is done at the lowest point in the gas

distribution system prior to gas burning appliances.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other appliance.

IMPORTANT

Before proceeding, please inspect the water heater and its components for

possible damage. DO NOT install any water heater with damaged

components. If damage is evident then please contact the supplier where the

water heater was purchased, or the manufacturer listed on the rating plate for

replacement parts.

General Information continued-

Make sure that you check the rating plate and combination gas control on the

water heater to be certain that the type of gas being supplied corresponds with

the marking on the rating plate and combination gas control.

A sacrificial anode(s) is used to extend tank life. Removal of any anode, except

for inspection and/or replacement, will nullify the warranty. In areas where

water is unusually active, an odor may occur at the hot water faucet due to a

reaction between the sacrificial anode and impurities in the water. If this should

happen, an alternative anode(s) may be purchased from the supplier that

installed this water heater. This will minimize the odor while protecting the tank.

Additionally, the water heater should be flushed with appropriate dissolvers to

eliminate any bacteria.

INSTALLATION

Locating The Water Heater

DO NOT install the water heater in any location where gasoline or

flammable vapors are likely to be present.

Water heaters in residential garages must be installed and located, or

protected, to avoid physical damage. For other installations refer to local

codes. In the absence of local codes, the water heater must be installed in

compliance with the National Fuel Gas Code, (ANSI Z223.1- Latest

Edition), or in Canada CAN/CGA B149.1 Natural Gas Installation Code

(Latest Edition) or CAN/CGA B149.2 Propane Installation Code (Latest

Edition).

UTION

This water heater must not be used as a source of construction

heat or durin

the construction phase of an

buildin

WARNING

This product contains one or more chemicals known to the State

of California to cause cancer, bi

th defects, or reproductive harm.

WARNING

Water heaters are heat producing appliances. To avoid damage or

injury, do not store materials against the water heater or vent-air intake

system. Use proper care to avoid unnecessary contact (especially by

children) with the water heater and vent-air intake components.

UNDER NO CIRCUMSTANCES SHOULD FLAMMABLE MATERIALS,

SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED

IN THE VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE

SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD

REACH THE WATER HEATER OR VENT-

IR INTAKE SYSTEM.

Installation (Locating The Water Heater) continued-

The location of this water heater is of the utmost importance. Before installing

this water heater, read the installation section of these instructions. After

reading these installation and operating instructions, select a location for the

water heater where the floor is level and is easily accessible to gas and water

supply lines. DO NOT locate the water heater where water lines could be

subjected to freezing temperatures. Make sure the cold water pipes are

not located directly above the gas control so that condensate during

humid weather does not drip on the controls.

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals. These

materials are corrosive at very low concentration levels with little or no odor to

reveal their presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED

BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY THE

WARRANTY. DO NOT OPERATE THE WATER HEATER IF EXPOSURE

HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE

COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable

way, or

b) Installed with an optional leg kit that includes legs and/or

extensions that provide a minimum clearance of 6” beneath the

water heater.

WARNING

Liquefied petroleum gases/propane gases are heavier than air and

will remain at floor level if there is a leak. Basements, crawl

spaces, closets, and areas below ground level will serve as

pockets for accumulation of leaking gas. Before lighting, smell all

around the appliance area for gas. Be sure to smell next to the

floor.

IF YOU SMELL GAS:

 DO NOT try to light any appliance.

 DO NOT touch any electric switch; do not use any telephone in

your building.

 Immediately call your gas supplier from a neighbor’s

telephone. Follow the gas supplier’s instructions.

 If you cannot reach your gas supplier, call the fire department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS

CORRECTED!

Installation (Locating The Water Heater) continued-

The water heater must be located close enough to the outside wall to keep the

venting distance within the maximum distance described in the installation

instructions. Locate the water heater as close as possible to the vent opening.

Read the venting section in this installation instruction manual before locating

the water heater.

This water heater must be located in an area where leakage of the tank or

water line connections and the combination temperature and pressure relief

valve will not result in damage to the area adjacent to the water heater or to

lower floors of the structure. When such locations cannot be avoided, a suitable

drain pan adequately piped for proper drainage must be installed under the

water heater. The pan must not restrict combustion air flow. The drain pan must

have a minimum length and width of at least 4 in (10.2 cm) greater than the

diameter of the water heater and must not restrict proper combustion air flow to

the water heater. The drain pan, as described above, can be purchased from

your plumbing professional. The drain pan must be piped to an adequate drain.

The piping must be at least 3/4 in (1.9 cm) in diameter and pitched for proper

drainage.

It is recommended that a minimum clearance of 4 in (10.2 cm) be provided on

the side of the water heater for servicing and maintenance of the combination

temperature and pressure relief valve.

This water heater MUST be installed indoors out of the wind and weather.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may be

obtained from the DSA Headquarters Office: 1102 Q Street, Suite 5100,

Sacramento CA 95811.

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT

CERTAIN OF THE FOLLOWING:

 Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in the detection of the gas.

 Most people recognize this odor as a “sulfur” or “rotten egg” smell.

 Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or “fade”, and not be as readily detectable.

 If you have a diminished sense of smell or are in any way unsure of the

presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

Gas detectors are available. Contact your gas supplier, or plumbing

professional, for more information.

Minimum Clearances

This installation must allow access to the front of the water heater and

adequate clearance must be provided for servicing and operating this water

heater. The water heater may be installed on either a combustible or non-

combustible floor. If the water heater is to be installed directly on carpeting, it

must be installed on top of a metal or wood panel extending beyond the full

width and depth of the appliance by at least 3 in (7.6 cm) in any direction or, if

the appliance is to be installed in an alcove or closet, the entire floor must be

covered by the panel. The minimum clearances to combustibles for this water

heater are: 0 in (0 cm) from the sides and rear, 5 in (12.7 cm) from the front of

the jacket, 0 in (0 cm) from the vent connector and 15 in (38.1 cm) from the

jacket top. Increased distances provide greater clearances for servicing.

Venting

Figure 1 - Vent Terminal Clearances

WARNING

Failure to adhere to these installation and operating instructions

may create a hazard to life and property and will nullify the

warrant

Venting continued-

Canadian

Installations1

Installations2

A= Clearance above grade, veranda, porch, deck or

balcony

12 inches

(30 cm) 12 inches

(30 cm)

Clearance to window or door that may be opened

12 inches

(30 cm)

4 feet (1.2 m)

below or to the

side of

opening;

12 inches

(30 cm) above

opening

Clea

ance to permanently closed window

Vertical clearance to ventilated soffit located

above the terminal within a horizontal distance of 2

feet (61 cm) from the center line of the terminal

Clearance to unventilated soffit

Clearance to outside corner

Clearance to inside corne

Clearance to each side of center line extended

above meter/regulator assembly

3 feet (91 cm)

within a height

15 feet (4.6 m)

above the

meter/regulator

assembly

I= Clearance to service regulator vent outlet or oil

tank vent

36 inches

(91 cm)

Clearance to non-mechanical air supply inlet to

building or the combustion air inlet to any other

appliance

12 inches

(30 cm)

4 feet (1.2m)

below or to

side of

opening;

12 inches

(30 cm) above

opening.

Clearance to a mechanical air supply inlet

6 feet

(1.83 m)

3 feet (91 cm)

above if within

10 feet (3.1 m)

horizontally

L= Clearance above paved sidewalk or paved

driveway located on public property

7 feet

(2.13 m) † 7 feet

(2.13 m) †

Clearance under a veranda, porch, deck, or

balcony

12 inches

(30 cm) ‡

1 In accordance with the current CAN/CGA-B149 Installation Codes.

2 In accordance with the current ANSI Z223.1-(Latest edition)/NFPA 54 National

Fuel Gas Code.

† A vent shall not terminate directly above a sidewalk or paved driveway that is

located between two single-family dwellings and serves both dwellings.

‡ Permitted only if a veranda, porch, deck or balcony is fully open on a minimum of

two sides beneath the floor.

*a) A minimum clearance value determined by testing in accordance with section

5.21.1 of ANSI Z21.10.1, latest edition.

*b) “Clearance in accordance with local installation codes and the requirements of

the gas supplier”.

Venting continued-

The vent system must terminate so that proper clearances are maintained as

cited in local codes or the latest edition of the National Fuel Gas Code, ANSI

Z223.1.73.4e and 7.8a, b as follows:

1. Do not terminate near soffit vents or crawl space or other area where

condensate or vapor could create a nuisance or hazard or cause property

damage.

2. Do not terminate the exhaust vent terminal where condensate or vapor

could cause damage or could be detrimental to the operation of regulators,

relief valves, or other equipment.

3. Do not terminate the exhaust vent terminal over public area or walkways

where condensate or vapor can cause nuisance or hazard.

4. The vent shall terminate a minimum of 12” (25.4 cm) above expected

snowfall level to prevent blockage of vent termination.

Vent pipes serving power vented appliances are classified by building codes as

“vent connectors”. Required clearances from combustible materials must be

provided in accordance with information in this manual under LOCATION OF

WATER HEATER and CLEARANCES, and with National Fuel Gas Code and

local codes.

Clearance to combustibles for all venting pipes

and terminals

For installations in the US

0” minimum

For installations in Canada

Refer to vent pipe and terminal

manufacturer’s installation

instructions for clearances to

combustibles

DO NOT place insulation or other materials in the required clearance spaces

between the venting to combustible material unless otherwise specified.

WARNING

Risk of carbon monoxide poisoning or fire due to joint separation

or pipe breaka

This water heater must be properly vented and connected to an

approved vent system in good condition. DO NOT operate water heater

with the absence of an approved vent system. A clean and

unobstructed vent system is necessary to allow noxious fumes that

could cause injury or loss of life to vent safely and will contribute toward

maintaining the water heater’s efficiency. The acceptance of the venting

system is dependent upon full compliance with these installation

instructions.

Ventin

stem must NOT pass throu

h rated fire separations.

The venting system must be free to expand and contract. This venting

stem must be supported in accordance with these instructions.

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White ECO-DEFENDER U130T*FRN Bedienungsanleitung

Bradford White

Bradford White KwickShot Bedienungsanleitung

Bradford White

Bradford White CHP-I&S-01 Handbuch

Bradford White

Bradford White M-2-50T6DS Bedienungsanleitung

Bradford White

Bradford White EFT-18000-2-T-10 Bedienungsanleitung

Bradford White

Bradford White EVERHOT TG-150E-N(X Service-Handbuch

Bradford White

Bradford White CombiCor TTW Bedienungsanleitung

Bradford White

Bradford White 238-44219-00J Beilage

Bradford White

Bradford White ElectriFLEX HD CEHD50 Bedienungsanleitung

Bradford White

Bradford White LG2PV50H653N Bedienungsanleitung

Bradford White

Bradford White ECO-DEFENDER EURG2DV40S N Series Bedienungsanleitung

Bradford White

Bradford White 203-B Bedienungsanleitung

Bradford White

Bradford White M-I-MH30T6FLX Bedienungsanleitung

Bradford White

Bradford White 355-B Bedienungsanleitung

Bradford White

Bradford White PDV Series Bedienungsanleitung

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White RE350T6-1NC Series Bedienungsanleitung

Bradford White

Bradford White EFT-15000-4-D-10 Bedienungsanleitung

Bradford White

Bradford White BW200-R Bedienungsanleitung

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White DS140S Beilage

Bradford White

Bradford White TTW URG2PV75H6N Bedienungsanleitung

Bradford White

Bradford White RE2H50R10-1NCWW Originalbetriebsanleitung

Bradford White

Bradford White Defender RG130T N Series Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung