Bradford White THROUGH-THE-WALL GAS WATER HEATER Bedienungsanleitung

238

40630

00M REV 12/03

THROUGH-THE-WALL GAS WATER HEATER

A Spanish language version of these instructions is available by contacting

the company listed on the rating plate.

La version espanola de estas instrucciones se puede obtener al escribirle

a la fabrica cuyo nombre aparece en la placa de especificaciones.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any

phone in your building.

•Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we

recommend Bradford White water heaters to be installed and

serviced by a plumbing professional.

TTW INSTALLATION AND OPERATING

INSTRUCTION MANUAL

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or death.

INTERNET VERSION FOR REFERENCE ONLY

CONGRATULATIONS!

You have just purchased one of the finest water heaters

on the market today!

This installation, operation and instruction manual will

explain in detail the installation and maintenance of your

new Through-The-Wall Gas Water Heater. We at Bradford

White strongly recommend that you contact a plumbing

professional for the installation of this water heater.

We require that you carefully read this manual, as well as

the enclosed warranty, and refer to it when questions

arise. If you have any specific questions concerning your

warranty, please consult the plumbing professional from

whom your water heater was purchased. For your

records we recommend that you write the model, serial

number and installation date of your water heater in the

maintenance section in the back of this manual.

This manual should be kept with the water heater.

At Bradford White we’re committed to providing you with

the finest water heater made.

INTERNET VERSION FOR REFERENCE ONLY

TABLE OF CONTENTS page

GENERAL INFORMATION............................................................... 4

INSTALLATION................................................................................. 5

Locating The Water Heater..................................................... 5

Minimum Clearances............................................................... 8

Venting...................................................................................... 9

Specifications for

48 Gal, 65,000 BTU input (189.3 L, 19.1 kW/Hr)

65 Gal, 65,000 BTU input (246.1 L, 19.1 kW/Hr)

75 Gal, 76,000 BTU input (283.9 L, 22.3 kW/Hr).......... 12

Specifications for

40 Gal, 40,000 BTU input (151.4 L, 11.7 kW/Hr)

48 Gal, 40,000 BTU input (189.3 L, 11.7 kW/Hr).......... 18

Combustion Air Supply............................................................ 24

Water Connections.................................................................. 26

Gas Connections ..................................................................... 29

Electrical Connections............................................................ 30

Wiring Diagram for

48 Gal, 65,000 BTU input (189.3 L, 19.1 kW/Hr)

65 Gal, 65,000 BTU input (246.1 L, 19.1 kW/Hr)

75 Gal, 76,000 BTU input (283.9 L, 22.3 kW/Hr).......... 31

Wiring Diagram for

40 Gal, 40,000 BTU input (151.4 L, 11.7 kW/Hr)

48 Gal, 40,000 BTU input (189.3 L, 11.7 kW/Hr).......... 32

GENERAL OPERATION.................................................................... 33

Lighting and Shutdown Instructions..................................... 34

Thermostat Adjustment........................................................... 35

Burner Flame Check................................................................ 36

MAINTENANCE................................................................................ 37

PARTS LIST DRAWING.................................................................... 40

PARTS LIST...................................................................................... 40

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING.............................................................................. 41

VENT PIPE PREPARATION AND JOINING ...................................... 42

NOTES.............................................................................................. 44

INTERNET VERSION FOR REFERENCE ONLY

GENERAL INFORMATION

This gas-fired water heater’s design is certified by CSA International under the

American National Standard Z21.10.1 -(as indicated on the rating plate) and

CSA 4.1-M-(as indicated on the rating plate).

This water heater must be installed in accordance with local codes or, in the

absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest

Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be held liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home. Such an

installation may create a hazardous condition and will nullify the warranty.

Do not use this appliance if any part has been submerged in water. You should

contact a qualified service technician to inspect the appliance and to replace any

part of the control system including the combination gas control which has been

submerged in water.

Make sure that you check the rating plate and combination gas control on the

water heater to be certain that the type of gas being supplied corresponds with

the marking on the rating plate and combination gas control.

CAUTION

Incorrect operation of this appliance may create a hazard to life and

property and will nullify the warranty.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

IMPORTANT

Before proceeding, please inspect the water heater and its components for

possible damage. DO NOTinstall any damaged components. If damage is

evident then please contact the supplier where the water heater was purchased

or the manufacturer listed on the rating plate for replacement parts.

INTERNET VERSION FOR REFERENCE ONLY

General Information continued-

A sacrificial anode is used to extend tank life. The removal of this anode, for any

reason, will nullify the warranty. In areas where water is unusually active, an odor

may occur at the hot water faucet due to a reaction between the sacrificial anode

and the impurities in the water. If this should happen, an alternative anode may

be purchased from the supplier that installed this water heater. This will minimize

the odor while protecting the tank. Additionally, the water heater should be

flushed with appropriate dissolvers to eliminate any bacteria.

INSTALLATION

Locating The Water Heater

DO NOT install the water heater in any location where gasoline or

flammable vapors are likely to be present.

Water Heaters in residential garages must be installed so that all burner(s)

and burner ignition device(s) are located not less than 18 inches (46 cm)

above the floor and must be located or protected to avoid physical

damage. For other installations refer to local codes. In the absence of

local codes, the water heater must be installed in compliance with the

National Fuel Gas Code, ANSI Z223.1 -(Latest Edition) and/or in Canada,

CAN/CGA B149 Installation Codes (Latest Editions).

The location of this water heater is of the utmost importance. Before installing

this water heater, read the installation section of these instructions. After reading

these installation and operating instructions, select a location for the water heater

where the floor is level and is easily accessible to gas and water supply lines. DO

NOT locate the water heater where water lines could be subjected to

freezing temperatures. Make sure the cold water pipes are not located

directly above the gas control so that condensate during humid weather

does not drip on the controls.

Installation (Locating The Water Heater) continued-

WARNING

Water heaters are heat producing appliances. To avoid damage or injury, do not

store materials against the water heater or vent-air intake system. Use proper

care to avoid unnecessary contact (especially by children) with the water heater

and vent-air intake components. UNDER NO CIRCUMSTANCES MUST

FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE

USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR

INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD

REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.

INTERNET VERSION FOR REFERENCE ONLY

Water heater corrosion and component failure can be caused by the heating and

breakdown of airborne chemical vapors. Examples of some typical compounds

that are potentially corrosive are: spray can propellants, cleaning solvents,

refrigerator and air conditioning refrigerants, swimming pool chemicals, calcium

and sodium chloride, waxes and process chemicals. These materials are

corrosive at very low concentration levels with little or no odor to reveal their

presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED BY EXPOSURE

TO CORROSIVE VAPORS IS NOT COVERED BY THE WARRANTY. DO NOT

OPERATE THE WATER HEATER IF EXPOSURE HAS OR WILL OCCUR. DO

NOT STORE ANY POTENTIALLY CORROSIVE COMPOUNDS IN THE

VICINITY OF THE WATER HEATER.

WARNING

Liquefied petroleum gases/propane gas are heavier than air and

will remain at floor level if there is a leak. Basements, crawl

spaces, closets, and areas below ground level will serve as

pockets for accumulation of leaking gas. Before lighting, smell

all around the appliance area for gas. Be sure to smell next to

the floor.

IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any telephone in

your building.

•Immediately call your gas supplier from a neighbor’s

telephone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire

department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS

CORRECTED!

INTERNET VERSION FOR REFERENCE ONLY

Installation (Locating The Water Heater) continued-

The water heater must be located close enough to the outside wall to keep the

venting distance within the maximum distance described in the installation

instructions. Read the venting section in this installation instruction manual

before locating the water heater.

This water heater must be located in an area where leakage of the tank or water

line connections and the combination temperature and pressure relief valve will

not result in damage to the area adjacent to the water heater or to lower floors of

the structure. When such locations cannot be avoided, a suitable drain pan

adequately piped for proper drainage must be installed under the water heater.

The pan must not restrict combustion air flow. The drain pan must be no greater

than 1-½ inches (3.8 cm) deep and have a minimum length and width of at least

four (4) inches (10.2 cm) measured from the jacket of the water heater. The drain

pan, as described above, can be purchased from your plumbing professional.

The drain pan must be piped to an adequate drain. The piping must be at least

3/4 inch (1.9 cm) in diameter and pitched for proper drainage.

It is recommended that a minimum clearance of four (4) inches (10.2 cm) be

provided on the side of the water heater for servicing and maintenance of the

combination temperature and pressure relief valve.

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT

CERTAIN OF THE FOLLOWING:

•Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in the detection of the

gas.

•Most people recognize this odor as a “sulfur” or “rotten egg” smell.

•Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or ”fade”, and not be as readily detectable.

•If you have a diminished sense of smell, or are in any way unsure of

the presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

•Gas detectors are available. Contact your gas supplier, or plumbing

professional, for more information.

INTERNET VERSION FOR REFERENCE ONLY

Installation (Minimum Clearances) continued-

Minimum Clearances

This installation must allow access to the front of the water heater and adequate

clearance must be provided for servicing and operating this water heater. The

water heater may be installed on either a combustible or non-combustible floor. If

the water heater is to be installed directly on carpeting, it must be installed on

top of a metal or wood panel extending beyond the full width and depth of the

appliance by at least three (3) inches (7.6 cm) in any direction or, if the appliance

is to be installed in an alcove or closet, the entire floor must be covered by the

panel. The minimum clearances to combustibles for this water heater are: zero

(0) inch (0 cm) from the sides and rear, five (5) inches (12.7 cm) from the front of

the jacket, zero (0) inch (0 cm)from the vent connector and fifteen (15) inches

(38.1 cm) from the jacket top.

WARNING

Failure to adhere to these installation and operating instructions may

create a hazard to life and property and will nullify the warranty.

INTERNET VERSION FOR REFERENCE ONLY

Venting

This venting section is divided into two parts. Part I will cover venting

specifications for 48 Gal -65,000 BTU (181.7 L -19.1 kW/Hr), 65 Gal -65,000

BTU (246.1 L -19.1 kW/Hr), and 75 Gal -76,000 BTU (283.9 L -22.3 kW/Hr)

models. Part II will cover venting specifications for 40 Gal -40,000 BTU

(151.4 L -11.7 kW/Hr) and 48 gal -40,000 BTU (181.7 L -11.7 kW/Hr)

models. Refer to the rating plate located on the water heater for correct

model identification.

The Nation Fuel Gas Code ANSI Z223.1-(Latest Edition), CGA/CAN B149 Installation

Code, and local codes have specific requirements for the location of the vent terminals

on vertical walls. The guidelines listed below are from the National Fuel Gas Code.

Consult the local codes, and/or National Fuel Gas Code ANSI Z223.1-(Latest Edition),

or CGA/CAN B149 Installation Code to determine if there are any additions or changes

to the following specifications.

(A) The vent terminal must terminate at least 3 feet (.91 m) above any forced

air inlet duct located within 10 feet (3 m). Exception: This provision shall

not apply to the combustion air intake of a direct vent appliance.

(B) The vent terminal must terminate at least 4 feet (1.2m) below, 4 feet (1.2

m) horizontally from, or 1 foot (.31 m) above any door, window, gravity air

inlet into the building.

above ground and above the anticipated snow level.

(D) The vent terminal must not terminate over a public walkway or over an

area where condensate or vapor could create a nuisance or hazard or

could be detrimental to the operation of regulators, relief valve, or other

equipment.

(E) The water heater location must provide easy access for the entire length

of the vent connector.

(F) The vent system must be inspected at least once a year to ensure

against leakage of exhaust products.

Exceptions For Installations in Canada:

(A) The vent terminal must be located at least 1 foot (.31 m) from any window

or door which can be opened in any building, any non-mechanical air

supply inlet to any building, or the combustion air to any inlet other

appliance.

(B) The vent terminal must be located at least 6 feet (1.8 m) from any

mechanical air supply inlet to the building.

within 3 feet (.91 m) horizontally of the vertical centerline of the regulator

and must be at least 6 feet (1.8 m) from any gas service regulator vent

outlet.

(D) The vent terminal must be at least 7 feet (2.1 m) above a paved sidewalk

or a paved driveway located on public property.

INTERNET VERSION FOR REFERENCE ONLY

(E) The vent terminal must not terminate above a paved sidewalk or a paved

driveway which is located on private adjacent property.

Venting (Part I) continued-

Venting System Condensation

Condensate formation does not occur in all installations of power vented heaters,

but should be protected against on installations where condensation can form in

the venting system.

Formation of condensation in the venting system of Power Vented water heaters

is dependent upon installation conditions including, but not limited to:

ambient temperature and humidity of installation location;

ambient temperature and humidity of venting space;

vent distance and slope;

and product usage.

In order to effectively control condensate from adversely affecting the mechanical

components of the water heater several methods may be employed:

1. For horizontal installations the vent pipe can be installed with a

downward slope (not less than 1/8" nor greater than ½” per foot

maximum) and away from the blower motor.

2. In order to prevent condensate from draining back into the blower (vertical

or horizontal runs), a fitting and drain hose is available as a condensate

trap kit (see Table 1 for service part numbers). The all rubber fitting with

drain outlet mounts directly to the blower motor outlet and is secured

with two hose clamps (one to the blower motor outlet and the other to the

vent connector). The plastic tubing is provided to drain any accumulated

condensate away from the water heater and to a suitable drain. The kit

comes complete with instructions for proper installation of the fitting.

Table 1

Model Service Part

2” (5.1 cm) Blower Outlet (exhaust) 239-42742-00

3” (7.6 cm) Blower Outlet (exhaust) 239-42743-00

Venting (Part I) continued-

INTERNET VERSION FOR REFERENCE ONLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White 50T Bedienungsanleitung

Bradford White

Bradford White EFC-5500-4-S-10 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Bradford White

Bradford White D4403S series Bedienungsanleitung

Bradford White

Bradford White MITW40L Series Bedienungsanleitung

Bradford White

Bradford White M-I-MH30T6FLX Bedienungsanleitung

Bradford White

Bradford White M1-2U6SS Bedienungsanleitung

Bradford White

Bradford White M-I-WH6U6SS Bedienungsanleitung

Bradford White

Bradford White Copper Brute II Bedienungsanleitung

Bradford White

Bradford White URG2PV75H N Series Bedienungsanleitung

Bradford White

Bradford White ElectriFLEX HD CEHD 50 Bedienungsanleitung

Bradford White

Bradford White LG2PDV50H60N Bedienungsanleitung

Bradford White

Bradford White D100T Bedienungsanleitung

Bradford White

Bradford White LT199NXX1 Kurzanleitung

Bradford White

Bradford White 238-46392-00G Montageanleitung

Bradford White

Bradford White URG2DV40S*N Bedienungsanleitung

Bradford White

Bradford White Electric Instantaneous Water Heaters Bedienungsanleitung

Bradford White

Bradford White 544-B Bedienungsanleitung

Bradford White

Bradford White TTW URG2PV75H6N Bedienungsanleitung

Bradford White

Bradford White PDX Series Bedienungsanleitung

Bradford White

Bradford White PV Series Bedienungsanleitung

Bradford White

Bradford White BNTH Bedienungsanleitung

Bradford White

Bradford White MII Series Bedienungsanleitung

Bradford White

Bradford White EFTM Montageanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung