Bradley Express MG-2/NDT Bedienungsanleitung

IMPORTANT!

Read this entire installation manual to ensure proper installation.

When finished with the installation, file this manual with the owner or

maintenance department.

Separate parts from packaging and make sure all parts are accounted

for before discarding any packaging material. If any parts are

missing, do not begin installation until you obtain the missing parts.

Make sure that all water supply lines have been flushed and then

completely turned off before beginning installation. Debris in supply

lines can cause valves to malfunction.

Hardware supplied by installer must be appropriate for wall

construction. Wall anchors used must have a minimum pull-out

rating of 1,000 lbs.

Product warranties may be found under "Product Information" on our

web site at www.bradleycorp.com.

Installation

MG-2/NDT

Express® Lavatory System MG-Series

with ndite™ Infrared Control

Express® Lavatory

Systems are ADA and

TAS compliant.

Patents Pending

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY Fax: (262) 251-5817

http:\\www.bradleycorp.com

215-1587 Rev. C; EN 06-915

Page 1 of 22 2/12/07

THIS

SIDE

Packing List



Installation

TAS

MG-2/NDT Installation

Table of Contents

Supplies Required By Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

MG-2/NDT Dimensions - Front, Top and Side Views . . . . . . . . . . . . . . . . . .3–4

Installation Instructions

Step 1 Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–6

Step 2 Rough-In Wall Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Step 3 Mount Frame to Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Step 3 Install Bowl Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Step 4 Connect Supply and Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Step 5 Connect Electrical and Supply Tubing . . . . . . . . . . . . . . . . . . . . . . . .10

Step 6 Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11–12

Cleaning and Maintenance Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Assembly of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14–17

Troubleshooting ndite™ components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18–19

Solenoid Valve Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Thermostatic Mixing Valve Maintenance and Troubleshooting . . . . . . . . . . . .21

Thermostatic Mixing Valve Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Cleaning the Strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-22

2 2/12/07 Bradley Corporation • 215-1587 Rev. C; EN 06-915

Supplies Required by Installer

(8) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum

pull-out rating of 1,000 lbs.)

1/2" NPT hot and cold supply piping

1-1/2" NPT drain piping

Installation MG-2/NDT

3Bradley Corporation • 215-1587 Rev. C; EN 06-915 2/12/07

MG-2/NDT Express® Lavatory System Dimensions

*Subtract 4" (102mm) from vertical dimensions for compliance with ADA guidelines for children's use.

22"

(559mm)

*39"

(991mm)

*33-1/2"

(851mm)

*29-1/2"

(749mm) *17-1/2"

(445mm)

21-1/2"

(546mm)

9-1/2"

(241mm)

27" (686mm)

47" (1194mm)

54"

(1372mm) 42"

(1067mm)

15"

(381mm) 15"

(381mm)

MG-2/NDT Express® Lavatory System Dimensions continued . . .

TASTAS

MG-2/NDT Installation

4 2/12/07 Bradley Corporation • 215-1587 Rev. C; EN 06-915

TAS Juvenile Height

Grades 6 thru 8 or 9

TAS Juvenile Height

Grades Pre-K thru 5 or 6

37-1/2"

(952mm)

32"

(813mm)

28"

(711mm)

16"

(406mm)

TASTAS

35-1/2"

(902mm)

30"

(762mm)

26"

(660mm)

14"

(356mm)

Installation MG-2/NDT

5Bradley Corporation • 215-1587 Rev. C; EN 06-915 2/12/07

Installation Instructions

Step 1: Rough in

NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing in

the MG-2/NDT Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Standard Height only. Make

sure to follow appropriate dimensions based on configuration and

required rim height. Review appropriate figure before beginning

rough-ins.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.

(102)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

*28-1/4"

(718)

*25-3/4"

(654)

1/2" NPT HOT AND COLD

SUPPLIES OR TEMPERED

SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

*Juvenile Height Mounting:

Subtract 4" (102mm) from vertical dimensions for compliance

with ADA guidelines for children's use.

Figure 1

Standard Height Mounting CENTERLINE

OF FIXTURE

*26"

(660)

*31-1/2"

(800)

*19-1/2"

(495)

(102)4" (102)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

MG-2/NDT Installation

6 2/12/07 Bradley Corporation • 215-1587 Rev. C; EN 06-915

TAS — Texas Accessibility Standards:

Juvenile Height (grades Pre-K thru 5 or 6)

Figure 1b

(102)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

26-3/4"

(679)

24-1/4"

(616)

1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

18"

(457)

(102)4" (102)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

30"

(762)

24-1/2"

(622)

Figure 1a

(102)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

24-3/4"

(629)

22-1/4"

(565)

1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

22-1/2"

(572)

28"

(711)

16"

(406)

(102)4" (102)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

TAS — Texas Accessibility Standards:

Juvenile Height (grades 6 thru 8 or 9)

Installation MG-2/NDT

7Bradley Corporation • 215-1587 Rev. C; EN 06-915 2/12/07

Installation Instructions continued . . .

Step 2: Rough in wall anchors

1. Install six 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer) at

the locations marked (ref. location “B” shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The dimensions for the wall anchors at location “A” are for reference only.

2. On the back of the bowl, measure the distance between the 3/4" bowl mounting holes. Divide this

measurement in half. Measure and mark this dimension on the wall to the left of the centerline

and to the right of the centerline. Install two 3/8" wall anchors with a minimum pull-out rating of

1,000 lbs. (supplied by installer) at the locations marked (ref. location “A” shown in Figure 1, 1a

or 1b on pages 5-6).

NOTE: The anchors will be used to mount the Express® bowl and frame to the wall.

Figure 2

1-1/2" NPT DRAIN

STUB OUT 2"

1/2" NPT HOT AND

COLD SUPPLIES OR

TEMPERED SUPPLY.

STUB OUT 2"

MG-2/NDT Installation

8 2/12/07 Bradley Corporation • 215-1587 Rev. C; EN 06-915

Installation Instructions continued . . .

Step 3: Mount frame to wall

1. Loosen, but do not remove the bottom three access panel screws.

2. Remove the top three access panel screws and washers securing the access panel to the frame and

remove the access panel (see Figure 3).

3. Position the frame with Terreon® End Caps attached, against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to

bend. If necessary, install shims to compensate for wall distortion.

4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind

the frame to ensure that it will not bend when anchored.

5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use

the 3/8" bolts and washers to mount the frame to the wall.

Figure 3

FRAME

STAINLESS STEEL

ACCESS PANEL

3/8" BOLTS AND WASHERS

(6) PLACES

TERREON®

END CAP

RIGHT

TERREON®

END CAP

LEFT

1/4" - 20 SCREWS

AND FINISHING

WASHERS

(5) PLACES

FRONT VIEW

Installation MG-2/NDT

9Bradley Corporation • 215-1587 Rev. C; EN 06-915 2/12/07

Installation Instructions continued . . .

Step 4: Install bowl assembly

IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixture

has soap option, refer to the soap system installation manual

215-1585 before installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not to

pinch tubing between bowl and frame.

2. Attach the front of the bowl assembly to the frame using the two 1/4-20 x 1/2" pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the

bolts. Overtightening bolts can damage the Terreon® material.

3. After the bowl assembly is attached to the frame, install the two 3/8" bolts and washers

(supplied by the installer) to bolt the bowl to the wall anchors. Do not overtighten bolts.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts.

See Figure 7 on page 14 for sprayhead mounting bolt locations.

Figure 4

3/8" BOLT

AND WASHER

TERREON®

END CAP (R) TERREON®

END CAP (L)

FRAME SPRAYHEAD 3/8" BOLT

AND WASHER

BOWL

1/4"-20 x 1/2"

PAN HEAD

SCREWS AND

WASHERS

(2) PLACES

BACK VIEW

MG-2/NDT Installation

10 2/12/07 Bradley Corporation • 215-1587 Rev. C; EN 06-915

Installation Instructions continued . . .

Step 5: Connecting supply

1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide

the valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see

Figure 5b). Then lift up to remove the valve bracket from the frame.

2. FOR HOT AND COLD SUPPLY: Attach the stop/check to the hot and cold water supply piping

from the wall. Connect the flexible hoses to the Vernatherm™ Mixing Valve and to the stop/checks

(see Figure 5a).

NOTE: The “H” on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Attach the stop/check to the 1/2" tempered supply line.

Connect the stop/check to the tempered line adapter with the flexible supply hose (Figure 5c).

3. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2" drain

pipe stubbed out of the wall.

4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into

place. Secure the strainer with the screw provided.

Figure 5c

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

TO SUPPLY LINE

Figure 5a

FLEXIBLE SUPPLY

HOSE

Vernatherm™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT HOT

WATER SUPPLY

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

TEMPERED

LINE ADAPTER

(S39-685)

Figure 5b

SLOT IN

FRAME

VALVE BRACKET

MOUNTING SCREW

Hot and

Cold

Supplies

Single

Tempered

Supply

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley Express SS-2N/BIR3/STD Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley S19-110SS Bedienungsanleitung

Bradley

Bradley Verge LVLD Series Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley S19-465 Bedienungsanleitung

Bradley

Bradley Terreon TDB3103 Bedienungsanleitung

Bradley

Bradley GLX-3 Bedienungsanleitung

Bradley

Bradley S19-120FM Bedienungsanleitung

Bradley

Bradley S19-125SBF Bedienungsanleitung

Bradley

Bradley FREQUENCY FL-1H Bedienungsanleitung

Bradley

Bradley Terreon MF2922 Kurzanleitung

Bradley

Bradley S19-125BF Bedienungsanleitung

Bradley

Bradley Verge LVGD1 Bedienungsanleitung

Bradley

Bradley MG Series Bedienungsanleitung

Bradley

Bradley Aerada 1200 Series Bedienungsanleitung

Bradley

Bradley Express ELX-3 Bedienungsanleitung

Bradley

Bradley EXPRESS MG-EXT Bedienungsanleitung

Bradley

Bradley S19-125SBF Bedienungsanleitung

Bradley

Bradley AERADA 1000 Series S53-326 AC Bedienungsanleitung

Bradley

Bradley S19-210SC Bedienungsanleitung

Bradley

Bradley Express Crescent CRS Series Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema