Bradley AERADA 1000 Series S53-326 AC Bedienungsanleitung

IMPORTANT!

Read this entire installation manual to ensure proper installation. When

ﬁnished with the installation, ﬁle this manual with the owner or maintenance

department. Compliance and conformity to local codes and ordinances is

the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for

before discarding packaging material. If any parts are missing, do not begin

installation until you obtain the missing parts.

Make sure that all water supply lines have been ﬂushed and then completely

turned off before beginning installation. Do not use pipe dope. Debris in

supply lines can cause valves to malfunction.

Product warranties may be found under “Products” on our web site at

www.bradleycorp.com.

Installation

THIS

SIDE

Packing List

•

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY Fax: 262-253-4161

www.bradleycorp.com

Installation

215-1628 Rev. A; EN 08-201

Page 1 of 14 5/21/08

Aerada 1000 Series Faucet

S53-326 AC Gooseneck

S53-327 DC Gooseneck

Aerada 1100 Series Faucet

S53-328 AC High Arc Infrared

S53-329 DC High Arc Infrared

Table of Contents

Supplies Required.......................2

Installation.............................4

Manual Settings ........................6

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . .9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 10

Care and Maintenance . . . . . . . . . . . . . . . . . 12

Multi-Faucet Transformer Wiring . . . . . . . . . 14

Aerada 1000

Aerada 1100

Aerada 1000/1100 Series Installation

25/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

EXPLANATION OF SYMBOLS

Symbol Meaning

WARNING Refers to a situation of potential danger that

may cause serious injury or death.

CAUTION Refers to a situation of potential danger that

may cause slight or medium injury or property

damage.

Refers to important information.

TECHNICAL SUPPORT

For additional technical assistance, visit our website or call us:

• www.bradleycorp.com

• 1-800-BRADLEY

ORDERS

For orders, contact your local representative, visit our website or call us:

• www.bradleycorp.com

• 1-800-BRADLEY

SAFETY INFORMATION

Read this entire user guide to ensure proper installation.

Compliance and conformity to local codes and ordinances is the responsibility of

the installer.

The following safety notes must always be complied with during handling of this

product:

• Make sure there is enough space and lighting available during installation and

service.

• Do not modify or convert this Faucet; any modiﬁcations will void warranties.

Installation may be performed at different times of construction by

different individuals. For this reason, these instructions should be left

on-site with the facility or maintenance manager.

Pressurized plumbing ﬁxtures shall be installed in accordance with

manufacturer´s recommendations. The supply piping to these devices

shall be securely anchored to the building structure to prevent installed

device from unnecessary movement when operated by the user. Care

shall be exercised when installing the device to prevent marring the

exposed signiﬁcant surface.

ACCESSORIES BRADLEY PART NO.

4” Cover Plate 150-221

Plugin Transformer 232-008

Hardwired Transformer (1–8 faucets) 232-009

2.2 GPM Laminar Flow for Gooseneck 269-1923

2.2 GPM Laminar Flow for Lavatory 269-1922

6V Lithium Battery CR-P2 261-010

•

Installation Aerada 1000/1100 Series

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 3

COMPONENT PARTS

Aerada 1100 Series

High Arc Components & Bradley Part Nos.

1. Spout with External Mixer opening [269-1960]

2. Shut Off Screw Assembly [269-1944]

3. Outlet Assembly Kit Lavatory Spout (.5 GPM) [269-1946]

4. Mixer Kit [269-1945]

5. 6 V Lithium Battery CR-P2 [261-010]

6. AC Adaptor Kit [269-1942]

7. Battery Holder Kit [269-1961]

8. Check Valve (1) [198-013]

9. Braided Hose (1) with inlet filter [269-1943]; Filter only [269-1948]

10. Deck Mounting Hardware Kit [269-1949]

11. Electronics Module Kit [269-1941]

12. Solenoid Valve [269-1940]

COMPONENT PARTS

Aerada 1000 Series

Gooseneck Components & Bradley Part Nos.

1. Spout [269-1958]

2. Shut Off Screw Assembly [269-1944]

3. Outlet Assembly Kit Spout (.5 GPM) [269-1947]

4. Gooseneck Base without opening [269-1959]

5. 6 V Lithium Battery CR-P2 [261-010]

6. AC Adaptor Kit [269-1942]

7. Battery Holder Kit [269-1961]

8. Check Valve (1) [198-013]

9. Braided Hose (1) with inlet filter [269-1943]; Filter only [269-1948]

10. Deck Mounting Hardware Kit [269-1949]

11. Electronics Module Kit [269-1941]

12. Solenoid Valve [269-1940]

1 a/b

Aerada 1000/1100 Series Installation

45/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

INSTALLATION

This faucet comes with all the components needed for installation,however, some

tools and supplies are not included.

• Basin Wrench

• Adjustable Wrench

• Adjustable Locking Pliers

• Plumber´s Putty

• Hex Key (supplied)

• Outlet Key (supplied)

Do not use pipe dope on faucet and supply connections. Possible

solenoid contamination could occur and will void any warranty.

Mounting of Lavatory and Gooseneck Faucet

Prerequisites

• Supply valve is installed

• Water supply lines are ﬂushed properly

• For AC faucets, power outlet is installed

It is not necessary to unscrew the connection between braided hose

and housing to install the product.

Do not remove protective covering from sensor until starting up faucet

operation.

Do not tighten locknut before step 4 is completed.

1 Mount cover plate if required. Plumber´s putty is recommended to seal the

cover plate to the sink. Security pin must be located on the left side.

2 Mount gasket and put faucet into sink.

3 Mount bracket from underneath. Place hoses through large opening and

mounting rod through small opening. Make sure ﬂange sits securely against

surface.

4 Place nut onto mounting rod and tighten with wrench.

5 If faucet was installed with cover plate, secure with basin washer, ﬂat washer

and locknut.

6 Install aerator and tighten with aerator key (supplied).

7 For Gooseneck faucets, tighten spout with wrench.

8 Connect braided hose with ﬁlter to supply valve

Cold water > white label Hot water > no label

For AC faucets, please refer to the plugin or hardwired transformer

installation instructions.

9 Connect to power supply.

Result: The faucet is now mounted.

Installation Aerada 1000/1100 Series

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 5

Start-up Operation

Prerequisites

• Faucet is mounted

• Water supply is on

• Water supply lines are ﬂushed properly

• For AC faucets, power outlet is installed.

1 Fully open supply valves.

2 Remove all items from sink.

3 Remove protective covering from sensor.

4 Wait for 15 seconds for the faucet to calibrate to its environment.

Result: The faucet is now activated.

15 sec.

Test Function

1 Hold hand in front of sensor.

> Water ﬂow starts

WARNING Hot water may burn your skin.

Hold hand carefully under water and remove quickly

2 For faucets with external mixer, turn mixer handle from cold to warm.

> Water temperature increases

3 Remove hand.

> Water ﬂow stops

Result: The function is now tested.

Aerada 1000/1100 Series Installation

65/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

Enabling “Manual Setting Mode”

A battery model is shown in the following example. These instructions apply

to all models. After 30 minutes, the “Manual Setting” mode will be disabled

automatically and all settings will be saved.

Prerequisites

• Water supply valve is open

• Battery is full (LED does not blink) for DC faucets

• AC power is on for AC faucets

1 Remove shut-off screw.

2 Remove mixer handle (only for faucets with external mixer).

3 Remove housing vertically.

4 Remove battery from battery holder.

5 The following procedure (a, b, c) must be done three (3) times in a row.

a - Re-insert battery

b - LED lights up

c - Remove battery immediately after LED switches off

6 Insert battery.

7 Mount housing vertically.

8 Mount shut-off screw.

Installation Aerada 1000/1100 Series

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 7

9 Mount mixer handle (only for faucets with external mixer)

Result: The faucet is now mounted.

A - Setting Cleaning Mode

Setting the cleaning mode will make the faucet inactive for 90 seconds.

1 Enable “Manual Setting” Mode

> See “Enabling Manual Setting Mode” section

2 Fully cover sensor with hand, until water ﬂow stops. (This takes 5 seconds.)

3 Remove hand.

Result: The Cleaning Mode is now active. For the next 90 seconds, the faucet

will be inactive.

B - Setting Normal Mode

Setting the normal mode will allow the faucet to activate only when it senses a

hand presence.

1 Enable “Manual Setting” Mode

> See “Enabling Manual Setting Mode” section

2 Fully cover sensor with hand. Water ﬂow stops after 5 seconds - Continue to

hold on for one (1) additional water pulse.

3 Remove hand.

Result: Normal Mode is now activated.

C - Setting Metering Mode (10 seconds)

Setting the metering mode will allow the faucet to activate for a full 10 seconds

after if senses a hand presence.

1 Enable “Manual Setting” Mode

> See “Enabling Manual Setting Mode” section

2 Fully cover sensor with hand. Water ﬂow stops after 5 seconds - Continue to

hold on for another two (2) additional water pulses.

3 Remove hand.

Result: Metering Mode is now activated for 10 seconds.

Aerada 1000/1100 Series Installation

85/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

D - Setting Scrub Mode (60 seconds)

Setting scrub mode for 60 seconds will allow the faucet to activate for 60

seconds from the last hand presence.

1 Enable “Manual Setting” Mode

> see “Enabling Manual Setting Mode” section

2 Fully cover sensor with hand. Water ﬂow stops after 5 seconds - Continue to

hold on for another three (3) additional water pulses.

3 Remove hand.

Result: Scrub Mode is now activated for 60 seconds.

E - Setting Scrub Mode (180 seconds)

Setting scrub mode for 180 seconds will allow the faucet to activate for 180

seconds from the last hand presence.

1 Enable “Manual Setting” Mode

> See “Enabling Manual Setting Mode” section

2 Fully cover sensor with hand. Water ﬂow stops after 5 seconds - Continue to

hold on for another four (4) additional water pulses.

3 Remove hand.

Result: Scrub Mode is now activated for 180 seconds.

F - Sensor Range Adjustment

The detection distance of the sensor can be adjusted between approximately

4 - 11 inches from the infrared window.

1 Enable “Manual Setting” Mode

> See “Enabling Manual Setting Mode” section

2 Remove all items from the sink.

2 Fully cover sensor with hand. Water ﬂow stops after 5 seconds - Continue to

hold on for ﬁve (5) additional water pulses.

4 Remove hand.

5 Hold hand in the current detection area until LED ﬂashes. Then move hand

to the desired detection distance. When LED stays lit for two (2) seconds,

detection distance has been re-set to new location.

Result: The detection distance is now calibrated.

G - Reset

All settings will be reset to default setting. The “Manual Setting” Mode will be

disabled.

> The procedure for the reset is the same as “Enabling Manual Setting Mode”,

but step 5 needs to be done six (6) times in a row.

Result: All settings are reset to default settings and the manual-setting-mode is

now disabled.

Installation Aerada 1000/1100 Series

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 9

FAUCET ADJUSTMENTS

Operating modes and sensor ranges can be adjusted with a manual operation through the infrared sensor.

Faucet adjustment operations apply to all models.

OPERATING MODES

In order to set the operating modes, the faucet needs to be placed into “Manual Setting” mode. At this time, operating modes can be changed within the next 30

minutes.

The following is a functional diagram to show the different settings available for manual faucet adjustment. See detailed instructions on pages 6 through 8.

FUNCTION DIAGRAM OF OPERATING MODES

Water pulses in seconds [s] Legend:

Operating Modes Description

A Cleaning Mode The faucet is inactive for 90 seconds.

B Normal Mode The faucet is activated if it senses a hand presence. This is the default operating mode of the faucet.

C Metering Mode (10 s) The faucet will shut off after 10 seconds regardless of hand presence detected.

D Scrub Mode (60 s) The faucet will shut off 60 seconds after the detection of the last hand presence.

E Scrub Mode (180 s) The faucet will shut off 180 seconds after the detection of the last hand presence.

F Sensor Range Adjustment Change the detection distance of the infrared sensor. The default sensor range is approximately 1” beyond the spout.

G Reset All settings will be reset to original factory settings.

Modes 5 4 14 14 14 14 1 Water is off

A - Cleaning Mode Water is on

B - Normal Mode

C - Metering Mode 10 s

D - Scrub Mode 60 s

E - Scrub Mode 180 s

F - Sensor Range Adjustment

Aerada 1000/1100 Series Installation

10 5/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

Problem Possible Cause Solution

No water ﬂow Supply valves are closed Open supply valves

Aerator is blocked or dirty Clean or replace aerator (See "Care and Maintenance")

Inlet water line ﬁlter is dirty or

blocked

Clean or replace ﬁlter (See "Care and Maintenance")

Braided hose is kinked Eliminate braided hose kink

No external water pressure Check water pressure/Provide water pressure

Battery is drained (DC

faucets only)

Replace battery (See "Care and Maintenance")

Battery contacts are

corroded (DC faucets only)

Clean contacts or replace battery

(See "Care and Maintenance")

Reverse battery insertion Insert battery correctly

Connector between

transformer and power

adapter unplugged (AC

faucets only)

Plug connector

Power adapter contacts are

corroded (AC faucets only)

Clean contacts

Connecting cable is kinked

or broken (AC faucets only)

Replace defective parts (See "Replacement Parts")

No external power supply

(AC faucets only)

Check external power supply/Provide power supply

Shut-off screw is missing or

defective

Replace shut-off screw (See "Replacement Parts")

Solenoid valve inoperable Replace solenoid valve (See "Replacement Parts")

Faucet is in cleaning mode Wait for cleaning mode to end (appr. 90 seconds)

Electronics module

inoperable

Contact Bradley technical service or replace power adapter (See

“Replacement Parts”)

Power adapter defective (AC

faucets only)

Contact Bradley technical service or replace power adapter (See

“Replacement Parts”)

Sensor distance is not

adjusted properly

Reset sensor monitoring range

Remove and re-install shut-off screw. Do not disturb sensor scanning

procedure (wait until water ﬂow stops and LED switches off)

Infrared window sctatched

or dirty

Clean window with smooth cloth

TROUBLESHOOTING

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley MG Series Bedienungsanleitung

Bradley

Bradley Terreon Quadra-Fount MF2944/IR Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley Terrazzo WF2613 Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S19-120 Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley Terreon TDB3104 Bedienungsanleitung

Bradley

Bradley Aerada 1000 Series Bedienungsanleitung

Bradley

Bradley S19-230T Bedienungsanleitung

Bradley

Bradley MF2939/BIR3 Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley Verge LVSD2 Bedienungsanleitung

Bradley

Bradley S19-304GA Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley S19-460EFW Bedienungsanleitung

Bradley

Bradley Verge LVQ Series Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley S19-110BFSS Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley S19-130SSBF Bedienungsanleitung

Bradley

Bradley S19-220TSS Bedienungsanleitung

Bradley

Bradley WS-1X Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema