Bradley MG Series Bedienungsanleitung

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1.800.BRADLEY Fax: 262.253.4161

bradleycorp.com

215-1586 Rev. D; ECN 13-08-025

Page 1 of 22 4/9/2014

Installation

MG-3/NDT

Express®Lavatory System

MG-Series

with NDITE® Infrared Control

Table of Contents

Supplies Required by Installer....................2

Dimensions ................................ 3-4

Installation Instructions ...................... 5-13

Cleaning and Maintenance .....................14

Assembly of Components ................... 15-18

Troubleshooting NDITE®Components ......... 19-20

Solenoid Valve Parts ..........................21

Navigator®Valve Maintenance and Parts ..........22

Cleaning the Strainer..........................22

Express®Lavatory Systems

are ADA and TAS compliant.

Patents Pending

MG-3/NDT Installation

24/9/2014 Bradley • 215-1586 Rev. D; ECN 13-08-025

Supplies Required by Installer

• (8)³⁄₈" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall

(minimumpull-outratingof1,000lbs.)

• ½"Nominalcoppertubingforhotandcoldsupplies

• 1½"NPTdrainpiping

IMPORTANT!

Read this entire installation manual to ensure proper installation. When finished

with the installation, file this manual with the owner or maintenance department.

Separate parts from packaging and make sure all parts are accounted for

before discarding any packaging material. If any parts are missing, do not begin

installation until you obtain the missing parts.

Make sure that all water supply lines have been flushed and then completely

turned off before beginning installation. Debris in supply lines can cause valves

to malfunction.

Hardware supplied by installer must be appropriate for wall construction. Wall

anchors used must have a minimum pull-out rating of 1,000 lbs.

Product warranties may be found under “Product Information" on our web site at

www.bradleycorp.com.

THIS

SIDE

Packing List

•

Installation

Installation MG-3/NDT

Bradley • 215-1586 Rev. D; ECN 13-08-025 4/9/2014 3

MG-3/NDT Express Lavatory System Dimensions

57"

(1445mm)

77"

(1956mm)

*Subtract 4" from vertical dimensions for compliance with ADA guidelines for children’s use.

22"

(559mm)

*39"

(991mm)

*33½"

(851mm)

*29½"

(749mm)

*17½"

(445mm)

21½"

(546mm)

9½" (241mm)

84"

(2134mm)

72"

(1829mm)

15" (381mm)

30"

(762mm)

30"

(762mm)

15" (381mm)

MG-3/NDT Installation

44/9/2014 Bradley • 215-1586 Rev. D; ECN 13-08-025

MG-3/NDT Express Lavatory System Dimensions continued . . .

TASTAS

TAS Juvenile Height

Grades 6 thru 8 or 9

TAS Juvenile Height

Grades Pre-K thru 5 or 6

37-1/2"

(952mm)

32"

(813mm)

28"

(711mm)

16"

(406mm)

TASTAS

35-1/2"

(902mm)

30"

(762mm)

26"

(660mm)

14"

(356mm)

Installation MG-3/NDT

Bradley • 215-1586 Rev. D; ECN 13-08-025 4/9/2014 5

Installation Instructions

Step 1: Rough in

NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing in

the MG-3/NDT Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply lines will

cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Standard Height only. Make sure to follow

appropriate dimensions based on configuration and required rim height. Review

appropriate figure before beginning rough-ins.

1. Roughin½"nominalcoppertubingforhotandcoldsupplylinesthroughwallatdimensionsshown.

2. Roughin1½"NPTdrainwasteconnectionthroughwallatdimensionsshown.

2¾"

(70mm)

4" (102mm)

FLOOR

28"

(711mm)

28"

(711mm)

*31½"

(800mm)

*28¼"

(718mm)

*26"

(660mm)

*19½"

(495mm)

³⁄₈" WALL ANCHORS, (8) PLACES

MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

1½" NPT DRAIN

STUB OUT 2"

*Juvenile Height Mounting:

Subtract 4" (102mm) from vertical dimensions for compliance with ADA guidelines for children’s use.

Figure 1

Standard Height Mounting

CENTERLINE OF FIXTURE

APPROX. DIMENSION

40½" (1029)

APPROX. DIMENSION

40½" (1029)

(102mm)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES

STUB OUT 2"

MG-3/NDT Installation

64/9/2014 Bradley • 215-1586 Rev. D; ECN 13-08-025

TAS — Texas Accessibility Standards:

Juvenile Height (grades Pre-K thru 5 or 6)

2¾" (70mm)

4" (102mm)FLOOR

28"

(711mm)

28"

(711mm)

28"

(711mm)

24¾"

(629mm)

22½"

(572mm)

16"

(406mm)

³⁄₈" WALL ANCHORS, (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

1½" NPT

DRAIN

STUB OUT 2"

Figure 1a

APPROX. DIMENSION

40½" (1029mm)

APPROX. DIMENSION

40½" (1029mm)

(102mm)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES

STUB OUT 2"

2¾" (70mm)

4" (102mm)FLOOR

28"

(711mm)

28"

(711mm)

30"

(762mm)

26¾"

(679mm)

24½"

(622mm)

18"

(457mm)

³⁄₈" WALL ANCHORS, (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

1½" NPT

DRAIN

STUB OUT 2"

Figure 1b

CENTERLINE

OF FIXTURE

APPROX. DIMENSION

40½" (1029mm)

APPROX. DIMENSION

40½" (1029mm)

(102mm)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES

STUB OUT 2"

TAS — Texas Accessibility Standards:

Juvenile Height (grades 6 thru 8 or 9)

CENTERLINE

OF FIXTURE

Installation MG-3/NDT

Bradley • 215-1586 Rev. D; ECN 13-08-025 4/9/2014 7

Installation Instructions continued . . .

Step 2: Rough in wall anchors

1. Install six ³⁄₈"wallanchorswithaminimumpull-outratingof1,000lbs.(suppliedbyinstaller)atthe

locationsmarked(ref.location“B"showninFigure1,1aor1bonpages5-6).

NOTE: The dimensions for the wall anchors at location “A" are for reference only.

2. On the back of the bowl, measure the distance between the ¾" bowl mounting holes. Divide this

measurement in half. Measure and mark this dimension on the wall to the left of the centerline and to the

right of the centerline. Install two ³⁄₈"wallanchorswithaminimumpull-outratingof1,000lbs.(suppliedby

installer)atthelocationsmarked(ref.location“A"showninFigure1,1aor1bonpages5-6).

NOTE: The anchors will be used to mount the Express bowl and frame to the wall.

Figure 2

1-1/2" NPT DRAIN

STUB OUT 2"

1/2" NOMINAL COPPER

TUBING FOR HOT AND

COLD SUPPLIES OR

TEMPERED SUPPLY.

STUB OUT 2"

MG-3/NDT Installation

84/9/2014 Bradley • 215-1586 Rev. D; ECN 13-08-025

Installation Instructions continued . . .

Step 3: Mount frame to wall

1. Loosen, but do not remove the bottom three access panel screws.

2. Remove the top three access panel screws and washers securing the access panel to the frame and

removetheaccesspanel(seeFigure3).

3. Position the frame with Terreon®End Caps attached, against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to bend. If

necessary, install shims to compensate for wall distortion.

4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind the frame to

ensure that it will not bend when anchored.

5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use the ³⁄₈"

bolts and washers to mount the frame to the wall.

Figure 3

³⁄₈" BOLTS AND WASHERS

(6) PLACES

TERREON

END CAP

LEFT

STAINLESS STEEL

ACCESS PANEL

TERREON

END CAP

RIGHT

FRAME

¼" - 20 SCREWS

AND FINISHING WASHERS

(6) PLACES

FRONT VIEW

Installation MG-3/NDT

Bradley • 215-1586 Rev. D; ECN 13-08-025 4/9/2014 9

Installation Instructions continued . . .

Step 4: Install bowl assembly

IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixture has soap option,

refer to the soap system installation manual 215-1585 before installing the bowl

assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not to pinch

tubing between bowl and frame.

2. Attachthefrontofthebowlassemblytotheframeusingthefour¼-20x½"pan-headscrewsandwashers

provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the bolts.

Overtightening bolts can damage the Terreon material.

3. After the bowl assembly is attached to the frame, install the two 3/8" bolts and washers

(suppliedbytheinstaller)toboltthebowltothewallanchors.Do not overtighten bolts.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts. See

Figure 7 on page 14 for sprayhead mounting bolt locations.

Figure 4

³⁄₈" BOLT

AND WASHER

TERREON

END CAP (R)

TERREON

END CAP (L)

FRAME SPRAYHEAD

³⁄₈" BOLT

AND WASHER

BOWL

¼"-20 x ½"

PAN HEAD

SCREWS AND

WASHERS

(4) PLACES

BACK VIEW

MG-3/NDT Installation

10 4/9/2014 Bradley • 215-1586 Rev. D; ECN 13-08-025

Installation Instructions continued . . .

Step 5: Connecting supply

1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the

valvebracketupuntilthelargercutoutintheframe’sslotalignswiththescrewhead(seeFigure5b).

Then lift up to remove the valve bracket from the frame.

2. FOR HOT AND COLD SUPPLY: Attach the stops to the hot and cold water supply piping from the wall.

ConnecttheflexiblehosestotheNavigatorMixingValveandtothestops(seeFigure5a).

NOTE: The “H" on Navigator Mixing Valve indicates hot water supply inlet.

 FORSINGLETEMPEREDSUPPLY:Attachthestoptothe½"temperedsupplyline.Connectthestopto

thetemperedlineadapterwiththeflexiblesupplyhose(Figure5c).

3. AssembletheP-trapbyconnectingthe1½"tubularpipetothetailpieceandtothe1½"drainpipe

stubbed out of the wall.

4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place.

Secure the strainer with the screw provided.

Figure 5c

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

TO SUPPLY

LINE

TEMPERED

LINE ADAPTER

(S39-804)

Figure 5a

NAVIGATOR

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

HOT WATER

SUPPLY

CONNECT TO

COLD WATER

SUPPLY

FLEXIBLE

SUPPLY

HOSE

Hot and Cold Supplies

Single Tempered

Supply

Figure 5b

SLOT IN

FRAME

VALVE BRACKET

MOUNTING SCREW

Andere Handbücher für MG Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley TDB3108 Bedienungsanleitung

Bradley

Bradley S19-230T Bedienungsanleitung

Bradley

Bradley Express SS-2N/BIR3/STD Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Express Crescent CRS-2/IR Bedienungsanleitung

Bradley

Bradley S19-310PVC Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley SN2013 Bedienungsanleitung

Bradley

Bradley SN2013/AST4 Bedienungsanleitung

Bradley

Bradley Corner-Fount MF2922 Kurzanleitung

Bradley

Bradley S19-220DCRPT Bedienungsanleitung

Bradley

Bradley P19-234 Bedienungsanleitung

Bradley

Bradley S19-120P Bedienungsanleitung

Bradley

Bradley S19-315BF Bedienungsanleitung

Bradley

Bradley S19-222 Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley TBD3103 Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley Terreon TDWL22 Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley E19-120A Bedienungsanleitung

Bradley

Bradley S19-280 Series Bedienungsanleitung

Bradley

Bradley S19-230FW Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema