Bradley EXPRESS SS-3/AST/JUV Bedienungsanleitung

IMPORTANT

Read this entire installation manual

to ensure proper installation, then

file these instructions with the

owner or maintenance department.

Flush all the water supply lines

before making connections.

Wall anchors used must have a

minimum pull-out rating of 1,000

lbs.

Product warranties may be found

under "Product Information" on our

web site at www.bradleycorp.com.

SS-3/AST/STD

SS-3/AST/JUV

Express® Lavatory

System SS-Series

(Standard and Juvenile Height)

Express® Lavatory

Systems are ADA

compliant.

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . . . . . . 5-11

Cleaning and Maintenance . . . . . . . . . . . . . . . .12

Soap Dispenser Maintenance . . . . . . . . . . .13-14

Check Valve Troubleshooting . . . . . . . . . . . . . .14

Assembly of Components . . . . . . . . . . . . . .15-16

Metering Air Valve Maintenance . . . . . . . . . . .17

Metering Air Valve Troubleshooting . . . . . .17-18

Vernatherm™ Thermostatic Mixing Valve . . . .19

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

215-1238 Rev. C; EN 03-813

Page 1 of 19 5/11/04

Installation

Instructions

For Service Only

Express® Lavatory System SS-Series

SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only

25/11/04 Bradley Corporation • 215-1238 Rev. C; EN 03-813

Pre-Installation Information

Barrier-free and ADA compliant - standard height mounting

The SS-3/AST/STD Express® Lavatory System must have a rim height of 34" above finished

floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim

height, the Express® meets ADA, ANSI and UFAS requirements for barrier-free clearances,

reaches and controls. Always check local codes and ordinances for compliance.

Barrier-free and ADA compliant - juvenile height mounting

The SS-3/AST/JUV Express® Lavatory System is compliant with Americans with Disabilities

Act (ADA) Accessibility Guidelines for Buildings and Facilities: Building Elements Designed for

Children's Use; Final Rule.

Pushbutton and air valve

Each sprayhead is controlled by a pushbutton air valve, enabling each user to activate a single flow

of water. Air valves use 0.5 gpm for a ten-second duration, meeting the ANSI/ASHRAE/IES

90A-1980 Standard.

Supplies required for installation:

• (8) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall

(minimum pull-out rating of 1,000 lbs.)

• 1/2" NPT hot and cold supply piping

• 1-1/2" NPT drain piping

Express® Lavatory System SS-Series

Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV

3Bradley Corporation • 215-1238 Rev. C; EN 03-813 5/11/04

(203)

52" (1321)

64" (1626)

(152)

80" (2032)

8" (203)

Radius

30"

(762)

8.5"

(216)

21"

(533)

30"

(762)

10" (254)

Radius

SS-3/AST/STD and SS-3/AST/JUV

Express® Lavatory System Dimensions

Dimensions

continue . . .

68-1/4" (1732)

Express® Lavatory System SS-Series

SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only

45/11/04 Bradley Corporation • 215-1238 Rev. C; EN 03-813

38"

(965) 34"

(864) 29"

(737)

11"

(279)

(229) 6"

(152)

(102)

30"

(762) 25"

(635)

11"

(279)

(229) 6"

(152)

(102)

34"

(864)

Standard Height

SS-3/AST/STD

Juvenile Height

SS-3/AST/JUV

SS-3/AST/STD and SS-3/AST/JUV

Express® Lavatory System Dimensions

continued . . .

Express® Lavatory System SS-Series

Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV

5Bradley Corporation • 215-1238 Rev. C; EN 03-813 5/11/04

Installation Instructions

Step 1: Rough in

Note: See Figure 1a below (for Standard Height) and Figure 1b on page 6 (for Juvenile Height)

when roughing in the Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1a are for Standard Height and in

Figure 1b for Juvenile Height.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.

3. Install (8) 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by

installer) at the locations shown in Figures 1a and 1b.

(MM)

32"

(813)

28-5/8"

(727)

23-1/2"

(597)

11-3/8"

(289)

(8) 3/8" WALL

ANCHORS WITH

MINIMUM PULLOUT

RATING OF 1,000

LBS.

38-1/2"

(978)

24-3/8"

(619)

2-3/4"

(70)

17-7/16"

(443)

38-1/2"

(978)

24-3/8"

(619) 4-3/8"

(111)

1/2" NPT HOT AND

COLD SUPPLIES

OR TEMPERED

SUPPLY - STUB

OUT 2" (50) FROM

WALL

Finished

Floor

CENTERLINE

15-1/4"

(387)

1-1/2" NPT DRAIN -

STUB OUT 3-1/2"

(89) FROM WALL

Figure 1a

SS-3/AST/STD Express® Lavatory System (Standard Height)

Installation Instructions

continue . . .

Express® Lavatory System SS-Series

SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only

65/11/04 Bradley Corporation • 215-1238 Rev. C; EN 03-813

(MM)

28"

(711)

24-5/8"

(625)

19-1/2"

(495)

11-3/8"

(289)

(8) 3/8" WALL

ANCHORS WITH

MINIMUM PULLOUT

RATING OF 1,000

LBS.

38-1/2"

(978)

24-3/8"

(619)

2-3/4"

(70)

17-7/16"

(443)

38-1/2"

(978)

24-3/8"

(619) 4-3/8"

(111)

1/2" NPT HOT AND

COLD SUPPLIES,

OR TEMPERED

SUPPLY

- STUB OUT 2" (50)

FROM WALL

FINISHED

FLOOR

CENTERLINE

15-1/4"

(387)

1-1/2" NPT DRAIN -

STUB OUT 3-1/2"

(89) FROM WALL

Figure 1b

SS-3/AST/JUV Express® Lavatory System (Juvenile Height)

Express® Lavatory System SS-Series

Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV

7Bradley Corporation • 215-1238 Rev. C; EN 03-813 5/11/04

Installation Instructions

continue . . .

Installation Instructions

continued . . .

Step 2: Mounting frame to wall

1. Remove the ten Torx-head screws securing the

panel to the frame, and remove the panel

(see Figure 3).

Note: Scuff panel does not need to be removed.

2. Position the frame against the wall, ensuring that

it is level. If necessary, insert shims under the

frame until level.

Note: When mounted, the Standard and Juvenile

Height frames should rest on the floor.

IMPORTANT: Anchoring the frame to a wall

that is

not

flat may cause the

frame to bend. If necessary,

install shims to compensate

for any wall distortion.

3. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims

behind the frame to ensure that it will not bend when anchored.

4. Once you have positioned the frame such that it is level and resting on the floor and flat

against the wall or shimmed, use the 3/8" bolts and washers to mount the frame to the wall

(see Figure 4).

Figure 4

(6) 3/8" BOLT

AND WASHER

FRAME

Figure 3

PANEL FRAME

(10) TORX-HEAD

SCREW

Figure 2

1-1/2” NPT DRAIN

STUB-OUT

1/2” NPT HOT AND COLD

SUPPLIES OR TEMPERED

SUPPLY - STUB-OUTS

Express® Lavatory System SS-Series

SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only

85/11/04 Bradley Corporation • 215-1238 Rev. C; EN 03-813

Installation Instructions

continued . . .

Step 3: Installing bowl assembly

IMPORTANT: Moving and positioning the bowl will require more than one person.

Note: Refer to Figure 5 below when installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame.

2. Attach the front of the bowl assembly to the frame using the four 1/4"-20 x 3/8" pan-head

screws and washers provided. Do not tighten bolts at this time.

IMPORTANT: When bolting the bowl assembly to the frame and wall, do not

overtighten bolts. Overtightening bolts can damage the Terreon®

material.

3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied by

the installer) to bolt the bowl to the wall anchors.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

Installation Instructions

continue . . .

Figure 5

3/8" BOLT

AND

WASHER

BOWL

ASSEMBLY

3/8" BOLT

AND WASHER

FRAME

1/4"-20 X 3/8"

PAN HEAD

SCREWS AND

WASHERS

BACK VIEW

Express® Lavatory System SS-Series

Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV

9Bradley Corporation • 215-1238 Rev. C; EN 03-813 5/11/04

Installation Instructions

continue . . .

Installation Instructions

continued . . .

Step 4: Connecting supply

1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™

Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a).

Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Connect the stop/strainer/check valve to the 1/2"

tempered supply line. Connect the flexible hose to the stop/strainer/check valve and air valve

manifold (see Figure 6b).

Figure 6a

FLEXIBLE

SUPPLY

HOSE VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

CONNECT TO

1/2" NPT HOT

WATER SUPPLY

Figure 6b

CONNECT E TO

TEMPERED

WATER SUPPLY

FLEXIBLE

SUPPLY

HOSE

CHECK VALVE

1/2 NIPPLE

(113-006DJ)

Express® Lavatory System SS-Series

SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only

10 5/11/04 Bradley Corporation • 215-1238 Rev. C; EN 03-813

Installation Instructions

continued . . .

Step 5: Connecting plastic tubing

NOTE: Refer to Figure 7a for hot and cold supplies, and refer to Figure 7b for tempered supply.

1. Connect the plastic tubing for the water supplies from the sprayhead assembly to the quick-

connect fittings on the air valve as follows:

• insert the tubing with the red marking to the left valve

• insert the tubing with the black marking to the middle valve

• insert the tubing with the green marking to the right valve

IMPORTANT: The plastic tubing for the water supplies and pushbuttons are

pre-cut to the correct lengths. If the tubing is cut too short,

kinking can occur and cause leaks at the fitting locations.

2. Connect the plastic tubing for the pushbuttons from the sprayhead assembly to the quick-connect

fittings on the air valve as follows:

• insert the tubing with the red marking to the left valve

• insert the tubing with the black marking to the middle valve

• insert the tubing with the green marking to the right valve

3. Assemble the P-trap (supplied) and make drain connections.

AIR TUBING

(GREEN)

AIR TUBING

(RED)

AIR TUBING

(BLACK)

Figure 7b

Figure 7a

VERNATHERM™

MIXING VALVE

FLEXIBLE

SUPPLY

HOSES

WATER SUPPLY

(BLACK)

WATER

SUPPLY

(GREEN)

AIR VALVE

WATER SUPPLY

(RED)

AIR VALVE

WATER

SUPPLY

(GREEN)

AIR TUBING

(GREEN)

AIR TUBING

(BLACK)

WATER SUPPLY

(BLACK)

WATER SUPPLY

(RED)

AIR TUBING

(RED)

FLEXIBLE

SUPPLY

HOSE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley S19-310BF Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Terreon MG Series Produktinformationsblatt

Bradley

Bradley FL-3H Bedienungsanleitung

Bradley

Bradley S19-220HFP Bedienungsanleitung

Bradley

Bradley FREQUENCY FL-1H Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley FREQUENCY FL-1H Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley SN2003 Kurzanleitung

Bradley

Bradley S19-230FW Bedienungsanleitung

Bradley

Bradley S19-220 Bedienungsanleitung

Bradley

Bradley S19-130SSBF Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley S19-430EFW Bedienungsanleitung

Bradley

Bradley S19-788 Bedienungsanleitung

Bradley

Bradley HN-400 Bedienungsanleitung

Bradley

Bradley TBD3103 Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley S19-120FM Bedienungsanleitung

Bradley

Bradley Terrazzo WF2613 Bedienungsanleitung

Bradley

Bradley S19-230H Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema