Bradley S19-220HFP Bedienungsanleitung

P.O. Box 309, Menomonee Falls, WI USA 53052-0309

PHONE 1-800-BRADLEY FAX (262) 251-5817

http://www.bradleycorp.com

215-158HFP Rev. J; EN 07-519

Page 1 of 6 8/9/07

S19-220HFP

Stainless Steel Wall-Mounted

Eyewash

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . 2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation Instructions . . . . . . . . . . . . . . . . . . 4

Assembly of Components . . . . . . . . . . . . . . . . 5

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation

114-063

P.O.BOX309,MENOMONEEFALLS,WI53052-0309USA

TEL:1-800-BRADLEYFAX:(262-251-5817)

www.bradleycorp.com

S19-220HFP Installation

8/9/07 Bradley Corporation • 215-158HFP Rev. J; EN 07-519

WARNING

Read this installation manual completely to ensure proper installation, then file it

with the owner or maintenance department. Compliance and conformity to drain

requirements and other local codes and ordinances is the responsibility of the

installer.

Separate parts from packaging and make sure all parts are accounted for before

discarding any packaging material. If any parts are missing, do not begin

installation until you obtain the missing parts.

Flush the water supply lines before beginning installation and after installation is

complete. Test the unit for leaks and adequate water flow. Main water supply to

the eyewash should be “ON” at all times. Provisions shall be made to prevent

unauthorized shutoff.

The ANSI Z358.1 standard requires an uninterruptable supply of flushing fluid at

a minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per

ANSI Z358.1.

The inspection and testing results of this equipment should be recorded weekly

to verify proper operation. This equipment should be inspected annually to

ensure compliance with ANSI Z358.1.

Workers who may come in contact with potentially hazardous materials should be

trained regarding the placement and proper operation of emergency equipment

per ANSI Z358.1.

For questions regarding the operation or installation of this product, visit

www.bradleycorp.com or call 1-800-BRADLEY.

Product warranties may also be found under ”Product Information” on our web

site at www.bradleycorp.com.

Installation

THIS

SIDE

Packing List

•

P.O.Box309,MenomoneeFalls,WI53051

TESTTHISUNITEACHWEEK

Test-operatevalve(s) each week and signbelow.

Reportany malfunctionsimmediately.

Ventil(e)wöchentlich im Te stbetriebprüfen, bestätigt

durchUnterschrift. Jegliche Störungsofort melden.

Date

Datum

Date

Signed

Unterschrift

Signe

Date

Date Signed

Signed

DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.

ESSAIHEBDOMADAIRE

Testle fonctionnement desvalveschaque semaine et

signeen bas.S'il y à quelque chose qui ne va pasfait

unrapport immédiatement.

P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

http://www.bradleycorp.com

114-051

Installation S19-220HFP

Bradley Corporation • 215-158HFP Rev. J; EN 07-519 8/9/07

S19-220HFP Dimensions

5/16" x 1-1/4"

(8mm x 32mm)

MOUNTING

SLOTS FOR

1/4" BOLTS

Ø 10-3/4" (254mm)

(102mm)

7-3/8"

(187mm)

Ø 2" (51mm)

Ø 1"

(25mm)

8-1/2"

(216mm)

35-11/16"

(906mm)

Suggested

Height

To Floor

2-3/8"

(60mm)

5-9/16"

(141mm)

6-15/16"

(176mm)

114-063

P.O.BOX 309,MENOMONEE FALLS, WI 53052-0309 USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

www.bradleycorp.com

13-1/2"

(343mm)

15-3/8" (391mm)

1/2" IPS Supply

1-1/4" IPS Drain

1/4"

(6mm)

Ø 1"

(25mm)

41-3/8"

(1051mm)

Suggested

Height

To Floor

Figure 1

NOTE: All dimensions assume standard thread engagement. Variations in manufacturing

allow for +/- 1/8" (3mm) per threaded joint. To find the tolerance of a dimension, add

the number of thread joints in between a dimension and multiply it by 1/8" (3mm).

S19-220HFP Installation

8/9/07 Bradley Corporation • 215-158HFP Rev. J; EN 07-519

Installation Instructions

Supplies Required:

• (2) 1/4" wall fasteners and bolts

• Pipe sealant

• Piping to 1/2" IPS water supply inlet and piping to 1-1/4" IPS drain outlet

• Sign-mounting hardware

Step 1: Mount eyewash and install supply piping

NOTE: The top of the eyewash heads should be 33"–45" (838mm–1143mm) from the floor. Refer to

Figure 1 on page 3 for appropriate dimensions.

1. Drill supply, drain, and operating rod holes at the dimensions shown in Figure 1.

2. Secure the eyewash receptor assembly to the wall using appropriate wall anchors and bolts (supplied

by installer).

3. Install the drain and supply piping (a

pply pipe sealant to all male-threaded pipe joints).

Step 2: Secure operating support sleeve

NOTE: This unit has been designed to accommodate varying wall thicknesses. When installing the

operating stem support sleeve (Item 19) it will be necessary to cut off one or both ends of the sleeve so

that 5/8" of threaded pipe protrudes from both sides of the wall.

1. Insert the operating support sleeve through the wall and secure in place with the nuts and washers

provided.

A slip joint has been provided for adjustment and is located directly below the automatic

weep drain fitting (Item 11).

Step 3: Assemble components

NOTE: Refer to the illustration on page 5 for component assemblies.

1. Assemble the components in the following order over the non-threaded end of the brass tube (Item 12):

connector kit (Item 13), brass friction ring (Item 15) and rubber washer (Item 14).

2. Insert the non-threaded end into the pipe (Item 8).

3. Align and screw the threaded end into the automatic weep drain. Tighten the nut (Item 13) on the pipe.

4. Insert the operating rod (Item 22) through the sleeve and attach handles (Items 23 and 24) with

the nuts and lockwashers provided.

Step 4: Connect water supply

1. Tighten all pipes and fittings maintaining proper alignment.

2. Connect the water supply piping to the 1/2" IPS inlet on the eyewash (piping supplied by

installer).

3. Connect drain piping to the 1-1/4" IPS drain outlet on the eyewash (piping supplied by installer).

4. Mount safety sign to wall using sign mounting hardware (supplied by installer).

5. Open the water supply lines. Test for leaks and adequate water flow.

Installation S19-220HFP

Bradley Corporation • 215-158HFP Rev. J; EN 07-519 8/9/07

Assembly of Components

P.O.Box 309, Menomonee Falls, WI 53051

TESTTHIS UNIT EACH WEEK

Test-operate valve(s) each week and sign below.

Report any malfunctionsimmediately.

Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt

durch Unterschrift.Jegliche Störungsofort melden.

Date

Datum

Date

Signed

Unterschrift

Signe

Date

Date Signed

Signed

DIESES GERÄT1ST WÖCHENTLICH ZU PRÜFEN.

ESSAI HEBDOMADAIRE

Test le fonctionnement desvalveschaque semaine et

signe en bas.S'il y à quelque chose qui ne va pasfait

un rapport immédiatement.

P.O.BOX 309,MENOMONEE FALLS, WI 53052-0309 USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

http://www.bradleycorp.com

114-051

114-063

P.O.BOX 309, MENOMONEE FALLS,W I53052-0309USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

www.bradleycorp.com

Flow Control

ThisEnd

1-1/4" IPS

Drain Outlet

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

11 17

22.1

918

18.1

1/2" IPS

Supply Inlet

Figure 2 NOTE: Items 1.1-1.10 come preassembled as Item 1.

S19-220HFP Installation

8/9/07 Bradley Corporation • 215-158HFP Rev. J; EN 07-519

Parts List

1 S90-302 1 Stainless Steel Bowl Assembly

1.1 111-039 1 Inlet-Drain Fitting

1.2 124-028 1 Gasket

1.3 140-645 1 Wall Bracket

1.4 124-024 1 Washer

1.5 187-053 1 Stainless Steel Bowl

1.6 173-009 1 Cup Strainer

1.7 S21-071 1 Supply Pipe Assy.

1.8 113-1159 1 Spacer, Drain

1.9 S05-091 1 Eyewash Yoke

1.10 107-371 2 Dust Cover

2 169-850 1 45° Street Elbow 1-1/4" IPS

3 113-006LT 1 Pipe 1-1/4" IPS x 6-1/2" Lg.

4 169-849 1 45° Elbow 1-1/4" IPS

5 113-006NQ 1 (0-8" wall)Pipe 1-1/4" IPS x 12-1/16"

113-006NT 1 (8-12" wall)Pipe 1-1/4" IPS x 16-1/16"

113-006NW 1 (12-18" wall)Pipe 1-1/4" IPS x 22-1/16"

6 169-764 1 Elbow 1-1/4" IPS

7 269-882 1 Connector

8 R68-600015 4 ft. Tube

9 113-006NP 1 (0"-8" wall) Pipe 1/2" IPS x 18-3/8"

113-006NS 1 (8"-12" wall) Pipe 1/2" IPS x 28-3/8"

113-006NV 1 (12"-18" wall) Pipe 1/2" IPS x 28-3/8"

10 169-838 1 Pipe Tee 1/2"

11 S29-068 1 Weep Valve Assy.

12 142-002DA 1 Washer

13 110-191 2 Connector Nut

14 110-115 1 Nut

15 153-372R 1 Adapter, Ball Valve

16 169-025 1 90° Street Elbow 1/2" IPS

17 113-006MS 1 Pipe 1/2" IPS x 3-3/4" lg.

18 S27-282 1 Stay-Open Ball Valve 1/2" IPS w/Nut

18.1 110-215 1 Nut only

19 113-006NN 1 (0"-8")pipe sleeve 1/2" IPS x 9-1/4"

113-006NR 1 (8"-12")pipe sleeve 1/2" IPS x 13-1/4"

113-006NU 1 (12"-18")pipe sleeve 1/2" IPS x 19-1/4"

20 142-002F 2 Washer-Metal

21 124-001F 2 Washer-Fiber

22 S21-067 1 (0"-8") Operating Rod

S21-067A 1 (8"-12") Operating Rod

S21-067B 1 (12"-18") Operating Rod

22.1 132-042 2 Retaining Ring

23 S08-308 1 Handle Assy.

24 128-151 1 Handle

25 161-036 2 Nut-Hex 5/16-18 Stn. Stl.

26 142-002BK 2 Lockwasher

27 114-051 1 Safety Sign

28 204-421 1 Emergency Tag

Item Part No. Qty Description Item Part No. Qty Description

Prepack S45-1782 includes Items 1.4, 1.6, 1.7, 1.8

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley Terreon MG Series Produktinformationsblatt

Bradley

Bradley Verge LVSD2 Bedienungsanleitung

Bradley

Bradley S19-310BF Bedienungsanleitung

Bradley

Bradley AERADA 1000 Series S53-326 AC Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley S19-220FWPT Bedienungsanleitung

Bradley

Bradley Verge WashBar LVQ Series Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley S19-110BFSS Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley Aerada 90-80 Series Bedienungsanleitung

Bradley

Bradley Navigator S19-2010 Series Bedienungsanleitung

Bradley

Bradley S19-430EH Bedienungsanleitung

Bradley

Bradley Aerada 1100 Series Bedienungsanleitung

Bradley

Bradley S19-230FW Bedienungsanleitung

Bradley

Bradley Terrazzo WF2600 Series Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley S19-120P Bedienungsanleitung

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley E19-120A Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley S19-200B Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema