Bradley MG-2/TT Bedienungsanleitung

MG-2/TT

Express® Lavatory

System - MG-Series

with TouchTime®Control

Installation

Instructions

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . . . . . . . . 5-12

Cleaning and Maintenance . . . . . . . . . . . . . . . . . .13

Assembly of Components . . . . . . . . . . . . . . . .14-16

Solenoid Valve Troubleshooting . . . . . . . . . . .17-18

Vernatherm™ Valve Maintenance . . . . . . . . .19-20

Cleaning the Strainer . . . . . . . . . . . . . . . . . . . .19-20

215-1480 Rev. E; EN 06-915

Page 1 of 20 2/8/07

IMPORTANT

Read this entire installation manual to ensure proper

installation.

Flush all the water supply lines before making connections.

Wall anchors used must have a minimum pull-out rating of

1,000 lbs.

File these instructions with the owner or maintenance

department.

Product warranties may be found under "Product

Information" on our web site at www.bradleycorp.com.

Express® Lavatory System - MG-Series with TouchTime® Control

MG-2/TT Installation Instructions

22/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915

Pre-Installation Information

Barrier-free and ADA compliant - standard height mounting

The MG-2/TT Express® Lavatory System must have a rim height no higher than 34" above finished

floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim height,

the MG-2/TT Express® Lavatory System meets ADA, ANSI and UFAS requirements for barrier-free

clearances, reaches and controls. Always check local codes and ordinances for compliance.

Barrier-free and ADA compliant - juvenile height mounting

The MG-2/TT Express® Lavatory System must have a rim height no higher than 30" above finished

floor to be compliant with Americans with Disabilities Act (ADA) Accessibility Guidelines for

Buildings and Facilities: Building Elements Designed for Children's Use; Final Rule.

Texas Accessibility Standards compliant:

The MG-2/TT Express® Lavatory System meets Texas Accessibility standards (TAS) for barrier-free

clearances, reaches and controls. Always check local codes and ordinances for compliance.

TouchTime®switch and solenoid

Each sprayhead is controlled by a TouchTime®switch, enabling each user to activate a single flow

of water. Each valve uses less than half the maximum of hot water allowed by the

ANSI/ASHRAE/IESNA 90.1-1989 Standard.

Supplies required for installation:

• (8) 3/8" wall anchors, bolts and washers to mount frame and bowl

to wall (minimum pull-out rating of 1,000 lbs.)

• 1/2" NPT hot and cold supply piping and 1-1/2" NPT drain piping

• 1/2" NPT street elbow

• 110 volt electrical outlet for 110/24 VAC plug-in transformer (supplied)

• 240/208-volt or 277-volt electrical outlet for optional electric tankless water heater

Express® Lavatory System - MG-Series with TouchTime® Control

Installation Instructions MG-2/TT

Bradley Corporation • 215-1480 Rev. E; EN 06-915 2/8/07

MG-2/TT Express® Lavatory System Dimensions

27"

(686)

47"

(1194)

54"

(1372) 42"

(1067)

15"

(381)

*Subtract 4" from vertical dimensions for compliance with ADA guidelines for children's use.

22"

(559)

*39"

(991)

*33-1/2"

(851)

*29-1/2"

(749) *17-1/2"

(445)

21-1/2"

(546)

9-1/2"

(241)

(mm)

15"

(381)

Express® Lavatory System - MG-Series with TouchTime® Control

MG-2/TT Installation Instructions

42/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915

Dimensions continued . . .

TAS Juvenile Height

Grades 6 thru 8 or 9

TAS Juvenile Height

Grades Pre-K thru 5 or 6

35-1/2"

(902)

30"

(762) 26"

(660) 14"

(356)

37-1/2"

(952)

32"

(813) 28"

(711) 16"

(406) FLOOR

FLOOR

(mm)

Express® Lavatory System - MG-Series with TouchTime® Control

Installation Instructions MG-2/TT

Bradley Corporation • 215-1480 Rev. E; EN 06-915 2/8/07

Installation Instructions

Step 1: Rough in supplies and optional hot water heater

NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing

in the MG-2/TT Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Standard Height Mounted

MG-2/TT Express®.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.

3. OPTIONAL HOT WATER HEATER: Rough in appropriate electrical supply per local code

(recommended 240/208-volt or 277-volt electrical box location shown below).

(102)

(127)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

*22-3/8"

(568)

*28-1/4"

(718)

*25-3/4"

(654)

1/2" NPT HOT AND COLD

SUPPLIES OR TEMPERED

SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

110V GFI

PROTECTED

ELECTRICAL

OUTLET

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

*Juvenile Height Mounting:

Subtract 4" from vertical dimensions for compliance with ADA guidelines for children's use.

Figure 1

Standard Height Mounting CENTERLINE

OF FIXTURE

*24-1/2"

(654)

*26"

(660)

*31-1/2"

(800)

3-3/4" (95)

*19-1/2"

(495)

(102)4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2-1/2"l x 3"w x 4"h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4"l x 3"w x 4"h)

*23"

(584)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

Express® Lavatory System - MG-Series with TouchTime® Control

MG-2/TT Installation Instructions

62/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915

Figure 1a

TAS - Texas Accessibility

Standards:

Juvenile Height (grades

Pre-K thru 5 or 6)

(102)

(127)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

18-7/8"

(479)

24-3/4"

(629)

22-1/4"

(565)

1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

21"

(533)

22-1/2"

(572)

28"

(711)

3-3/4" (95)

16"

(406)

(102)4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2-1/2"l x 3"w x 4"h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4"l x 3"w x 4"h)

19-1/2"

(495)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

Figure 1b

TAS - Texas Accessibility

Standards:

Juvenile Height (grades 6

thru 8 or 9)

(102)

(127)

FLOOR

APPROX. DIMENSION

14"

(356)

14"

(356)

26-3/4"

(679)

24-1/4"

(616)

1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY – STUB OUT 2"

1-1/2" NPT DRAIN

STUB OUT 2"

3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

23"

(584)

3-3/4" (95)

18"

(457)

(102)4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2-1/2"l x 3"w x 4"h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4"l x 3"w x 4"h)

21-1/2"

(546)

16-1/2"

(419)

25-1/2" (648)

APPROX. DIMENSION

25-1/2" (648)

A A

BB B

30"

(762)

20-7/8"

(530)

24-1/2"

(622)

110V GFI

PROTECTED

ELECTRICAL

OUTLET

110V GFI

PROTECTED

ELECTRICAL

OUTLET

Express® Lavatory System - MG-Series with TouchTime® Control

Installation Instructions MG-2/TT

Bradley Corporation • 215-1480 Rev. E; EN 06-915 2/8/07

Installation Instructions continued . . .

Step 2: Rough in wall anchors and electrical outlet

IMPORTANT: Turn OFF electrical power to the outlet when installing the Express®

Lavatory System.

1. Install a 110 volt GFI protected electrical outlet per local code at the location shown in Figure 2.

2. Install six 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer)

at the locations marked (ref. location “B” shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The dimensions for the wall anchors at location “A” are for reference only.

3. On the back of the bowl, measure the distance between the 3/4" bowl mounting holes. Divide

this measurement in half. Measure and mark this dimension on the wall to the left of the

centerline and to the right of the centerline. Install two 3/8" wall anchors with a minimum pull-

out rating of 1,000 lbs. (supplied by installer) at the locations marked (ref. location “A” shown in

Figure 1, 1a or 1b on pages 5-6).

NOTE: The anchors will be used to mount the Express® MG-2/IR bowl and frame to the wall.

Figure 2

110 VOLT GFCI

ELECTRICAL OUTLET

TRANSFORMER

LOCATION

1-1/2" NPT DRAIN

STUB OUT 2"

1/2" NPT HOT AND

COLD SUPPLIES OR

TEMPERED SUPPLY.

STUB OUT 2"

Express® Lavatory System - MG-Series with TouchTime® Control

MG-2/TT Installation Instructions

82/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915

Installation Instructions continued . . .

Step 3: Mount frame to wall

1. Loosen, but do not remove the three bottom access panel screws.

2. Remove the two top access panel screws and washers securing the access panel to the frame and

remove the access panel (see Figure 3).

3. Position the frame with Terreon® End Caps attached, against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to

bend. If necessary, install shims to compensate for wall distortion.

4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind

the frame to ensure that it will not bend when anchored.

5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use

the 3/8" bolts and washers to mount the frame to the wall.

Figure 3

FRAME

STAINLESS STEEL

ACCESS PANEL

3/8" BOLTS AND WASHERS

(6) PLACES

TERREON®

END CAP

RIGHT

TERREON®

END CAP

LEFT

1/4" - 20 SCREWS

AND FINISHING

WASHERS

(5) PLACES

FRONT VIEW

Express® Lavatory System - MG-Series with TouchTime® Control

Installation Instructions MG-2/TT

Bradley Corporation • 215-1480 Rev. E; EN 06-915 2/8/07

Installation Instructions continued . . .

Step 4: Install bowl assembly

IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixture

has soap option, refer to the soap installation manual 215-1585

before installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not

to pinch tubing between bowl and frame.

2. Attach the front of the bowl assembly to the frame using the two 1/4-20 x 1/2" pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the

bolts. Overtightening bolts can damage the Terreon® material.

3. After the bowl assembly is attached to the frame, install the two 3/8" bolts and washers

(supplied by the installer) to bolt the bowl to the wall anchors. Do not overtighten bolts.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts.

See Figure 8 on page 14 for sprayhead mounting bolt locations.

Figure 4

3/8" BOLT

AND WASHER

TERREON®

END CAP (R) TERREON®

END CAP (L)

FRAME SPRAYHEAD 3/8" BOLT

AND WASHER

BOWL

1/4"-20 x 1/2"

PAN HEAD

SCREWS AND

WASHERS

(2) PLACES

BACK VIEW

Express® Lavatory System - MG-Series with TouchTime® Control

MG-2/TT Installation Instructions

10 2/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915

Installation Instructions continued . . .

Step 5: Connecting supply

1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide

the valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see

Figure 5b). Then lift up to remove the valve bracket from the frame.

2 FOR HOT AND COLD SUPPLY: Attach the stop/check to the hot and cold water supply piping

from the wall. Connect the flexible hoses to the Vernatherm™ Mixing Valve and to the

check/stops (see Figure 5a).

NOTE: The “H” on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Attach the stop/check to the 1/2" tempered supply line.

Connect the stop/check to the tempered line adapter with the flexible supply hose (Figure 5c).

3. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2" drain

pipe stubbed out of the wall.

4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into

place. Secure the stainer with the screw provided.

Figure 5a

FLEXIBLE SUPPLY

HOSE

VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT HOT

WATER SUPPLY

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

Figure 5c

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

TO SUPPLY LINE

TEMPERED

LINE ADAPTER

(S39-685)

Hot and

Cold

Supplies

Single

Tempered

Supply

Figure 5b

SLOT IN

FRAME

VALVE BRACKET

MOUNTING SCREW

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley Express SS-2N/AST/STD Bedienungsanleitung

Bradley

Bradley E19-120A Bedienungsanleitung

Bradley

Bradley S19-220SS Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Verge WashBar LVQ Series Bedienungsanleitung

Bradley

Bradley S19-220SC Bedienungsanleitung

Bradley

Bradley S19-130SSBF Bedienungsanleitung

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley TBD3103 Bedienungsanleitung

Bradley

Bradley EXPRESS SS-3/AST/JUV Bedienungsanleitung

Bradley

Bradley Express ELX-3 Bedienungsanleitung

Bradley

Bradley Aerada 1100 Series Bedienungsanleitung

Bradley

Bradley EXPRESS SS-2/AST/JUV Bedienungsanleitung

Bradley

Bradley S19-230H Bedienungsanleitung

Bradley

Bradley Aerada 1000 Series Bedienungsanleitung

Bradley

Bradley Aerada 90-80 Series Bedienungsanleitung

Bradley

Bradley OmniDeck 3000 Series Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley Verge Crestt Series Kurzanleitung

Bradley

Bradley S19-220DCSS Bedienungsanleitung

Bradley

Bradley Terreon Quadra-Fount MF2944/IR Bedienungsanleitung

Bradley

Bradley Sentry SN2003/TT Bedienungsanleitung

Bradley

Bradley S45-1986 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema