Brigade MDR-304 Bedienungsanleitung

.%3

%JHJUBM7JEFP3FDPSEFS

*OTUSVDUJPO.BOVBM

'FC

FIRMWARE: 1.40B

SAFETY PRECAUTIONS

All the following safety and operation instructions which will prevent harm or damage to the operator or

other persons should be read before the unit is operated.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Do not block ventilation openings.

Do not place anything on top of the unit that might spill or fall into it.

Do not attempt to service this unit yourself as opening or removing covers may expose you

to dangerous voltage or other hazards. Please refer all servicing to qualified service

personnel.

Do not use liquid cleaners or aerosols for cleaning.

This installation should be made by a qualified service person and should conform to all

local codes.

To prevent fire or electric shock, do not overload wall outlets or extension cords.

This unit must be grounded to reduce the risk of electric shock hazard.

CAUTION

Danger of explosion if battery( RTC Battery ) is incorrectly replaced. Replace only with the

same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Risk of explosion if replaced by an incorrect type. Dispose of used batteries according to the

instructions.

CONTENTS

1.2 Product Introduction................................3

1.3 Product Features ....................................4

1.5 THE FRONT / REAR VIEWS..................5

1.5.1 The Front View......................................5

1.5.2 The Rear View ......................................7

1.5.3 The Inner Caddy Rear View..................8

1.5.4 The GPS Connector..............................8

1.5.5 The Camera In Connector ....................9

1.5.6 The Power Delay Connection...............9

1.5.7 The Power Connector.........................10

1.6 I/O Port......................................................

..................................................................11

1.7 The I/O Connections.............................12

1.8 Voltage Management............................13

2. INSTALLATION ................................. 14

2.1 The Basic Connections.........................14

2.3 System Information and........................16

Channel Selection.......................................16

2.3.1 System information.............................16

2.3.2 Channel Selection...............................16

2.4 Updating the System Software .............17

PERATIONS .......................................... 18

3.1 Configuring the Recording Settings ......18

3.2 The Recording Operations....................20

3.2.1 Manual Recording...............................20

3.2.2 Alarm Recording .................................20

3.2.3 Externally Triggered Recording ..........20

3.3 The Playback Operations......................21

3.3.1 Normal Playback.................................21

3.3.2 Fast Forward/Backward......................21

3.3.3 Slow Forward/Reverse....................... 21

3.3.4 Play back picture-by-picture............... 22

3.4 The Search Operations........................ 22

3.4.1 The FULL LIST Search ...................... 22

3.4.2 The ALARM LIST Search................... 22

3.4.3 The TIME Search............................... 23

3.4.4 The THUMBNAIL Search................... 23

3.4.5 The SD CARD Search ....................... 24

3.5 The Backup Operations ....................... 25

3.5.1 The SD Card Backup Operations....... 25

3.6 The Key Lock Operation ...................... 26

4. MENU SETUP.................................... 27

4.1 The REC Setting.................................. 27

4.2 The ALARM Setting ............................. 29

4.3 The CLOCK/ TITLE Setting.................. 31

4.4 The COMMUNICATION Setting........... 32

4.5 The DISK Setting ................................. 32

4.6 The SYSTEM Setting........................... 33

4.7 Notices of Motion and Alarm Setting.... 35

5.1 The RS-232 Setup & Protocol.............. 36

5.1.1 The RS-232 Protocol.......................... 36

5.1.2 The Communication Protocol............. 36

5.2 The System Default.............................. 39

5.3 O.S.D Messages.................................. 40

5.4 The Time Index Table.......................... 41

5.5 Specifications....................................... 42

APPENDIX 1. –FAQ................................... 43

APPENDIX 2: Quick Installation Guide...... 44

INTRODUCTION (continued)

1.2 Product Introduction

This MDR-304 is an advanced vehicle video recorder. It can simultaneously display real-time images from

four cameras along with information data via the mobile video recorder screened directly onto your monitor.

The mobile MDR-304 has four video channels which you can access either in the quad mode or in single

channel.

We use a hard disk device in this mobile recorder to store your images over a longer time. The recording

device has already been further tested for shock-proof and extreme temperature-proof durability in rugged

environments, with ventilation holes provided to lower the internal temperature for cooling.

The special design of our MDR-304 enables you to easily retrieve the recording caddys inside, which are

handy and portable enough to carry anywhere you want and link up with PCs and TV monitors for direct

display.

The MDR-304 includes the Global Position System (GPS) which helps disclose a vehicle's location

information -- the GPS information can also be displayed by eMap software to learn about a car's exact route.

The MDR-304 can also be connected to the car's information Black Box to access a vehicle's driving speed,

engine RPM, wheel turns, driving time periods, braking, signal lights, and so on, all of which data is received

and saved by the MDR-304. While searching for information, any important image you may want to save can

be stored via an SD card.

This mobile recorder provides all the above practical and useful features you can expect of it. It's your best

possible choice out of the entire range of mobile video recorders available. This multi-functional mobile video

surveillance product protects the safety of both the driver and the passengers.

1.3 Product Features

 Quad-based operation: real-time operation and playback (30 FPS/ per channel).

 M-JPEG compression with resolution up to 720X480 (NTSC) / 720X576 (PAL).

 4x 6-pin Din connectors for AV inputs.

 4 camera audio inputs, 2 auxiliary audio inputs, 1 audio output.

 The HDD's video records can be plugged in and played back on a TV directly.

 Pre-alarm image recording.

 USB interface showing video records in a PC.

 1 fixed 2.5" IDE HDD as storage medium for extended continuous digital recording.

 Supports GPS (RS-232).

 GPIO: 4 inputs and 2 outputs.

 Operating Voltage: 12Vdc.

 Maximum Current: 1.2Amps.

 Power Consumption: 15 Watts.

 Operation temperature: Standard HDD: 0 – 45℃(32 –113℉)

Industrial HDD: 0 – 60℃(32 –140℉)

 Dimensions: 178 x 173 x 50 mm.

 Time-lapse and real-time recording.

 Refresh rates up to 30 IPS (25 IPS for PAL).

 Image quality selectable at 4 different levels for recording.

 Alarm recording mode.

 Quick search by time, alarm, event, and recording list.

 Fast and slow playback of recorded video at various speeds.

 Single-picture playback.

 On-screen setup menu, title and system timer.

 Password protection.

 Disk-full warning and operation status LEDs.

 RS-232 communication port.

 Remote controller.

 Operation-status record log.

 Automatic detection of the current voltage.

 Audio function included.

 Built-in SD card slot for copying images to an SD card.

 Watermark.

 Window Division.

 Vibration and mechanical shock protection.

1.5 THE FRONT / REAR VIEWS

1.5.1 The Front View

SETUP button:

Press this to enter the setup menu. Press

again to exit the setup mode.

Left/ Right/ Up/ Down (CH1/ CH2/

CH4/ CH3) buttons:

In the menu setup mode / search mode,

press the four buttons on the dial to

highlight desired items in the menu

setup mode. In the live / play mode,

press the four buttons on the dial to

select a channel for display.

REW button:

Press this to play a recorded video in

the reverse direction at a speed that's

faster or slower than the recorded speed

in the play mode.

PLAY button:

Press to play back a recorded video

from the hard disk. (Alight glows green

in the PLAY mode.)

PAUSE button:

In a playback display, press this to

freeze the display. During the freeze,

press to display one frame of a picture

at a time in the forward direction ( a light

glows red in the PAUSE mode.)

FF button:

Press this to play a recorded video in

the forward direction at a speed that's

faster or slower than the recorded speed

in the play mode

STOP button:

Press to stop playing back a recorded

video ( a light glows red in the STOP

mode.)

REC button:

Push to start recording video into a hard

disk while in the live display mode.( a light

glows red in the REC mode.)

Inner-case lock:

This key lock secures the inner case

with the hard disk in place. When you

lock it in, it powers on the device. When

you unlock this key and take out the

inner case, the power turns off

automatically.

SEARCH button:

Press to enter the search mode to

access recorded video.

DISPLAY button:

Press to show the system operation

status on the screen.

Enter / (Quad) button:

Press to enter a selected item and save

the setting in the menu setup mode. In

the live/ play mode, use this button to

show a quad display.

SD CARD slot:

This is used for system software

updating and archiving/ accessing of

critical images.

USB port:

This is used for system picture playing.

Use this port to connect with your PC or

notebook. You can easily and quickly

capture data from a hard disk in the

vehicle MDR-304.

1.5.2 The Rear View

GPS & Remote Controller Connector:

The left side connector links up with the GPS receiver to capture local position information data.

Please refer to section 1.5.4 GPS CONNECTOR. The right side connector links up with the remote

controller

Audio Out / Video Out:

Your LCD monitor or other monitor can signal here.

AUX 1 / AUX 2:

Use this if you have external audio sources.

4 5

Camera In connector:

There are four connectors here to connect the Video / Audio In from a camera. Please refer to section

1.5.5 CAMERA IN CONNECTOR.

RS 232 port:

This communication port functions as a connector to an external device, for example a data box.

I / O port:

This connector links up with an external device.

Power Delay:

This connector will avoid the vehicle device getting excess power. Please refer to section 1.5.6

POWER DELAY CONNECTION.

Power Input:

This connector links up with the power from the vehicle (12V). Please refer to section 1.5.7 POWER

CONNECTOR.

1.5.3 The Inner Caddy Rear View

Plug Inlet:

The inlet connects to an external power supply. Connect to the 5V DC UL Listed Class 2 Power

Supply.

Hard Metric Connector (Male):

This connector links up with the outer casing.

Audio Connector:

Connect here to hear the audio's sound when you play the inner caddy case outside the outer case.

Video Connector:

Connect here to play the video when you play the inner caddy case outside the outer case.

1.5.4 The GPS Connector

( The PS/2 composition of the male connector)

PIN NO. PIN assignment

1. + 5V DC

2. Not Connected

3. RX

4. Ground

5. TX

6. Not Connected

1.5.5 The Camera In Connector

( PS/2 composition of the female connector)

PIN NO. PIN assignment

1. Audio In

2. Not Connected (Mirror)

3. + 12V DC

4. Video In

5. Ground

6. Ground

Note: The maximum electric current provided for 4 mobile cameras is 1 ampere ( 1A ) in total.

1.5.6 The Power Delay Connection

The diagram here illustrates the power delay connection structure. If a device needs to work with our

MDR-304, it needs to start operating after our MDR-304 has begun operating. See the diagram below

to help you with the mobile vehicle video recorder's power delay connector on its rear panel.

Enter the mobile vehicle MDR-304's "MAIN MENU" page and choose the third item, "CLOCK / TITLE".

Now enter the "CLOCK / TITLE" page, and you will see two items, "DELAY ON" and "DELAY OFF". For

both these items, the default setting is "OFF". You can set the delay time of the relay by choosing one of the

following options.

DELAY ON: This entry sets the delay time of the function activation of the relay connector after the

MDR-304 powers up.

DELAY OFF: This entry sets the delay time of the function activation of the relay connector after the ACC is

powered off. The relay connector will function as per the delay time you set by your chosen

option. After the relay connector's delay time duration is over, the relay connector will

automatically turn off, followed by the MDR-304 ( the MDR-304 which is connected with the

cigar-lighter of a vehicle for power supply will stop working when the ignition is turned off).

Note: The relay connector’s electric current range goes to a maximum of 30 amperes.

Note: Our "POST REC DURATION" function also sets the time as per any of the six options available, after

the ACC has been turned off. Please always be mindful of the fact that, if the time duration set for

either "DELAY OFF" or "POST REC DURATION" is longer than the other one, the MDR-304 will wait

for the longer setting to end before shutting down.

Andere Handbücher für MDR-304

Inhaltsverzeichnis

Andere Brigade DVR Handbücher

Brigade

Brigade MDR-304 Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung