Bristan BRG 3HBAS C Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Bright Tap Range

Models covered:

BRG 3HBAS C, BRG 3HBF C,

BRG WMBAS C, BRG WMBF C

www.divapor.com

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 4

Dimensions............................................................................... 5-7

Installation Requirements ....................................................... 8

Installation................................................................................ 9-10

3 Hole Basin Mixer / Bath Filler............................................... 9

Wall Mounted Basin Mixer / Bath Filler .................................. 10

Maintenance ............................................................................. 11

Troubleshooting........................................................................ 12

Notes......................................................................................... 13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

www.divapor.com

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This ﬁtting needs to be installed in accordance with, and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing the new ﬁtting it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the ﬁtting.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

• This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

www.divapor.com

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C.

A stored water temperature of 60°C is considered sufﬁcient to meet all normal

requirements and will minimise the build up of lime scale in hard water areas.

If the product is installed at low pressure (tank fed), then the minimum distance from

the highest installed position of the outlet to the underside of the cold tank should be at

least 2 metres to ensure adequate performance.

Note: BRG 3HBF C and BRG 3HBAS C require 3 metres if installed on a low pressure

system.

These taps and mixers should be installed in compliance with the Water Regulations.

Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the

mains, approved check valves must be ﬁtted in the supply pipes.

Speciﬁcations

Product Code

Working pressure

Inlet

Min Max

BRG 3HBAS C 0.3 5.0 15mm Compression Threaded Tail

BRG 3HBF C 0.3 5.0 3/4" BSP Threaded Tail

BRG WMBAS C 0.2 5.0 15mm Compression Threaded Tail

BRG WMBF C 0.2 5.0 22mm Compression Threaded Tail

Maximum static pressure- 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

www.divapor.com

Dimensions

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

3 Hole Basin Mixer

3 Hole Bath Filler

99 88

116

100

14 110

125

122

www.divapor.com

Dimensions Cont.

Wall Mounted Basin Mixer

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

290

47 207

30 172

www.divapor.com

Dimensions Cont.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions are approximate and in millimetres.

360

47 207

30 172

Wall Mounted Bath Filler

www.divapor.com

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household pipework to

ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

www.divapor.com

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

1. Unscrew the locking nut from the side

bodies.

2. With the backnut, metal and rubber

washers ﬁtted to the side body threaded tails,

feed the side body through the hole in the

basin / bath from underneath.

3. Screw the locking nut onto the valve,

ensuring the washer is ﬁtted between the

locking nut and basin / bath, onto the treaded

tail and tighten backnut underneath onto the

bottom of the basin/ bath. The screws on the

backnut allow for any uneven surfaces and

should be tightened up to the metal washer.

Replace the handle, grub screw and the rubber

cap.

4. Fit the spout to the basin/ bath tightening the

backnut. The screws on the backnut allow for

any uneven surfaces and should be tightened

up to metal washer.

5. Attach the T- joint assembly and connect to

the side bodies (hot on the left, cold on the right

when viewed from the front), by using ﬂexi tails

supplied.

6. Connect the hot and cold water supplies

to the side bodies (hot to the left, cold on the

right hand side), fully open both valves, letting

the water run for a few minutes to ﬂush the

system.

7. Fit the clicker waste (basin mixer only)

ensuring the rubber washer is ﬁtted between

the basin and the waste. Place the other

rubber washer under the basin and secure in

place by tightening the backnut. In order to

ﬁll the basin, the button in the middle of the

waste needs to be pressed down.

To release the water, press the button again.

8. Check all joints and connections

for leaks.

3 Hole Basin Mixer/ Bath Filler

www.divapor.com

Installation Cont.

Wall Mounted Basin Mixer and Bath Filler

1. Decide on the ﬁnal position of the basin mixer/ bath

ﬁller. Install suitable battons into the wall cavity if

required to support the tap body.

2. Plumb the hot and cold water supply pipes to the

required position.

3. Secure mixer body using the screws and wall plugs

supplied.

4. Attach the supply pipework to the hot and cold

inlets (hot on the left and cold on the right when

viewed from the front) ensuring the olive is ﬁtted to

the copper pipe work. Tighten the compression nut to

secure the pipework and create a water tight seal.

Note: Before ﬁnishing the wall surface turn on both

water supplies to check for any leaking connections.

5. Push the valve shroud onto the valve and secure by

using the shroud locking nut.

6. Finish the wall surface.

Note, it is important that a sufﬁcient amount of the

spout connecting tube is left exposed to allow the

spout to connect.

7. Attach the spout to the concealing plate using the

screws supplied.

8. Push the concealing plate over the valve shrouds

ensuring the o-rings on the spout connecting tube

have located inside the spout. Tighten the grub screw

to secure the spout in place and push ﬁt the rubber

cap.

9. Push the handles onto the valve spindles. Tighten

the grub screws and push ﬁt the rubber cap.

10. Turn on both water supplies and operate the

handle letting the water ﬂow for a few minutes to

ﬂush the system.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

www.divapor.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan Pisa series Verdrahtungsschema

Bristan

Bristan W BASIN08 C Bedienungsanleitung

Bristan

Bristan TY2 SDIV C Montageanleitung

Bristan

Bristan Cadet Verdrahtungsschema

Bristan

Bristan W BATH02 C Verdrahtungsschema

Bristan

Bristan ARM WORD01 C Bedienungsanleitung

Bristan

Bristan CR SHXDIVFF C Montageanleitung

Bristan

Bristan QD SHXSMFF C D3 Verdrahtungsschema

Bristan

Bristan Joy care Montageanleitung

Bristan

Bristan Blade Bath Shower Mixer BL BSM C Bedienungsanleitung

Bristan

Bristan HOU SHC3DIV C Verdrahtungsschema

Bristan

Bristan Java J SFSNK EF C Bedienungsanleitung

Bristan

Bristan Prism Eco Click Bedienungsanleitung

Bristan

Bristan W-BASIN01-C Verdrahtungsschema

Bristan

Bristan Star FH STRD01 C Bedienungsanleitung

Bristan

Bristan CRAZE CRZ2 SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan Target TG SNK C Bedienungsanleitung

Bristan

Bristan QST BAS2 C Bedienungsanleitung

Bristan

Bristan TFS 1 C Verdrahtungsschema

Bristan

Bristan Hourglass HOU BSM C Verdrahtungsschema

Bristan

Bristan Moloko Bedienungsanleitung

Bristan

Bristan FHC CTRD01 C Bedienungsanleitung

Bristan

Bristan W BASIN12 C Bedienungsanleitung

Bristan

Bristan Vantage VTX 1/2 C Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung