Bristan TFS 1 C Verdrahtungsschema

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

& User Guide

Temperature Control Time

Flow Shower

Models covered: TFS 1 C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

Speciﬁcations ........................................................................... 4

Dimensions .............................................................................. 5

Pack Contents .......................................................................... 6

Installation................................................................................ 7-8

Operation & Temperature Setting ........................................... 9

Maintenance ............................................................................. 10-11

Troubleshooting ....................................................................... 12-13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This ﬁtting needs to be installed in accordance with, and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

Unplug equipment

after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing the new ﬁtting it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the ﬁtting.

•Your ﬁtting has a high quality ﬁnish and should be treated with care to preserve the

visible surfaces. All surfaces will wear if not cleaned correctly, the only safe way

to clean your ﬁtting is to wipe with a soft damp cloth. Stains can be removed using

washing up liquid. All bath cleaning powders and liquids will damage the surface of

your ﬁtting, even the non-scratch cleaners.

Note: Never use abrasive detergents or disinfectants or those containing alcohol,

hydrochloric acid or phosphoric acid.

•This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Speciﬁcations

Inlet Connections: 15mm Compression with 145-165mm between centres.

Outlet Connection: 22mm Compression.

Minimum working pressure: 1.0 bar

Maximum working pressure: 5.0 bar

Maximum static pressure: 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Timed Flow: 30 Seconds ±5 Seconds

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws.

For full Installation Requirements & Notes (IRN) please visit www.wras.co.uk/directory.

Designed to comply with and be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C.

A stored water temperature of 60°C is considered sufﬁcient to meet all normal

requirements and will minimise the build up of lime scale in hard water areas.

If the ﬁtting is installed at low pressure (tank fed), then the minimum distance from the

highest installed position of the outlet to the underside of the cold tank should be at

least 10 metres to ensure adequate performance.

This shower should be installed in compliance with the Water Regulations. Where

the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the mains,

approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

882

32 80

G3/4"

145-165

Pack Contents

1 Shower Valve x1

2 Elbows x2

3 Olives x2

4 Compression Nuts x2

5 Shrouds x2

6 Filter Washers x2

7 8 L/P/M Flow Regulator x1

8 Screws x2

9 Wall Plugs x2

10 Riser Rail x1

11 Riser Clamp x1

12 Nut x1

13 Washer x1

14 Shower Head x1

Suggested Fittings (Not Supplied)

1/2" Female

Wall plate elbow

1/2" Female -

Copper

connector

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

1. Prepare water supply pipes

Terminate suitable pipework inside the

wall cavity / stud partition with

145-165mm pipe centres and 1/2" BSP

female connectors.

Flush through the pipework to ensure

removal of any debris.

Important: The pipework and 1/2" BSP

female connectors must be secure and

rigid so that it is unable to move. If

installing the pipework in a stud

partition, a wooden batton may be

required to secure the female connectors

(as shown).

The 1/2" BSP female connectors must be

installed in such a position that when the

elbow shrouds are screwed fully onto the

elbows and the valve is ﬁtted to the wall,

the elbow shrouds are ﬂush against the

ﬁnished wall surface. This is to ensure

that the valve can not move.

Note: If 1/2" female connectors are not

used the compression nut and olives can

be used however the pipework must be

secure and rigid so that it is unable to

move.

2. Finish Wall

Finish the wall surface using

plasterboard and tiles.

3. Fit Elbows

Screw the elbows into the 1/2" BSP

female connectors using a suitable thread

sealant.

Installation

Tiles

1/2" BSP

Female

Connection

Pipework

Supporting

Batton

Plaster Board

1/2" BSP

Female

Connection

Elbow

1/2" BSP

Female

Connection

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

Riser

Tube

Riser

Clamp

4. Fit Shower Valve

Place the shower valve body into position against

the wall and adjust the elbows to the valve body

ensuring the ﬁlter washers are ﬁtted into the

elbow nuts. Tighten the elbow nuts ensuring

the are fully tightened with the use of a suitable

spanner.

Note: Take care not to damage the ﬁnish of the

ﬁxing nuts. Protect the chromium plated surfaces

with a cloth.

Fit the 8 l/p/m ﬂow regulator into the shower

valve outlet.

5. Fit Rigid Riser Tube

Screw the rigid riser tube onto the shower valve

outlet ensuring the washer is ﬁtted.

Ensure vertical with the use of a sprit level and

tighten the nut fully using a suitable spanner.

Fit the riser clamp using the ﬁxings supplied or

suitable ﬁxings for wall / surface type.

Important: The riser clamp must be ﬁtted

200mm above the centre of the shower valve to

ensure maximum security.

6. Fit Shower Head

Remove the grub screw from the top of the

showerhead and remove the backplate. Push the

backplate into the top of the riser ensuring the

nipple is fully ﬁtted into the riser and mark the

position on the wall surface. Remove the

backplate from the riser tube and unscrew the

centre nut to reveal the backplate ﬁxing.

Position the backplate ﬁxing onto the wall at the

marked position and mark the ﬁxing holes onto

the wall surface. Drill suitable holes and secure

the backplate to the wall using suitable

ﬁxings (Not supplied).

Fit the backplate into the top of the riser tube

and onto the backplate ﬁxing and secure with the

centre nut. Replace the shower head and secure

in position with the top grub screw.

200mm from

centre of valve

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

8 L/P/M Flow

Regulator

Filter

Washer

Elbow

Operation & Temperature Setting

Hotter

Colder

1. Flow Control

Tooperate the ﬂow of water push the

central control knob firmly in and release.

The water will ﬂow for approximately 30

seconds ±5 seconds.

2. Temperature

Turn the control knob clockwise for

a cooler temperature.

Turn the control knob anti-clockwise

for a hotter water temperature.

Maximum Temperature Setting

Loosen the body nut (1) by a quarter turn

to allow rotation of the inner ring (2).

Turn the control kbob to full cold and

press push in to obtain a ﬂow of water.

Insert a Ø4.5mm rod into the adjustment

hole in the inner ring (2) and rotate anti-

clockwise until the ring cannot move any

more.

Rotate the control knob anti-clockwise

until the maximum water temperature is

obtained.

Tighten the body nut (1) fully ensuring the

adjustment position has been maintained.

Push and release

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Maintenance

Your ﬁtting has a high quality ﬁnish and should be treated with care

to preserve the visible surfaces. All surfaces will wear if not cleaned

correctly, the only safe way to clean your mixer is to wipe with a soft

damp cloth. Stains can be removed using washing up liquid. All bath

cleaning powders and liquids will damage the surface of your ﬁtting,

even the non-scratch cleaners.

Note: Never use abrasive detergents or disinfectants or those

containing alcohol, hydrochloric acid or phosphoric acid.

Before carrying out any maintenance, turn

off both water supply or close any isolating

valves to the shower valve. Operate the

shower to release any built up water pressure

within the shower.

Loosen the large body nut using a suitable

spanner.

Note: Take care not to damage the ﬁnish

of the nut. Protect the chromium plated

surfaces with a cloth.

Pull the handle away from the body to remove

the cartridge assembly from the shower valve

body.

Clean any debris off the cartridge assembly

using clean running water only.

Grease the 'O' rings using a suitable silicon

grease and push the cartridge assembly back

into the shower valve body.

Note: The cartridge assembly has a locating

pin which needs to ﬁtted into the body at the

bottom.

Tighten the large body nut securely using a

suitable spanner taking care not to damage

the chromium plated surface.

Turn on both water supplies and test the

shower valve.

Cleaning the Cartridge

General Cleaning

Cartridge Assembly

Cap

'O' Ring

Large body nut

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan RV SNK C Bedienungsanleitung

Bristan

Bristan COB SHC3STP C (D9) Verdrahtungsschema

Bristan

Bristan Quadrant Riser Rail kit Bedienungsanleitung

Bristan

Bristan VR1000 Bedienungsanleitung

Bristan

Bristan JAVA J THBSMVO C Verdrahtungsschema

Bristan

Bristan CR SHXDIVFF C Verdrahtungsschema

Bristan

Bristan W BASIN14 C Verdrahtungsschema

Bristan

Bristan SOQ2 SHUAR C Montageanleitung

Bristan

Bristan Options Bath Bedienungsanleitung

Bristan

Bristan Quest Bedienungsanleitung

Bristan

Bristan Artisan AR2 SHXMTFF2 C Montageanleitung

Bristan

Bristan FHC CTRD01 C Bedienungsanleitung

Bristan

Bristan HY POWSHX W Montageanleitung

Bristan

Bristan SMILE SM 1/2 C D6 Verdrahtungsschema

Bristan

Bristan W BASIN08 C Verdrahtungsschema

Bristan

Bristan RS2 BSM C (D3) Verdrahtungsschema

Bristan

Bristan Jute JU BSM C Bedienungsanleitung

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan HOU BSM C Verdrahtungsschema

Bristan

Bristan W BATH07 C Verdrahtungsschema

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan BRG 3HBAS C Bedienungsanleitung

Bristan

Bristan Palermo PA BSM C Bedienungsanleitung

Bristan

Bristan CR SHXDIVFF C Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung