Bristan Moloko Bedienungsanleitung

Moloko Thermostatic Surface Mounted Bar

Shower Valve With Fast Fit Connections

Fitting Instructions

& Contents List

Before starting any installation project, consider “Safety” first. Look for the “safety note”

sign and read the safety advice.

Prior to drilling into walls, check there are no hidden electrical wires, cables or water

supply pipes with the aid of an electronic detector. If you use power tools do not forget:

• Wear eye protection

• Unplug equipment after use

Please Keep These Instructions For Future Reference and Request of

Replacement Parts.

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

Contents

Section Description Page No:

1. Introduction 2

2. Specification 2

3. Pack contents checklist 2

4. Installation 3

5. Setting 6

6. Operation 6

7. General fault diagnosis 7

8. Cleaning & Maintenance 7

9. Guarantee & Registration 8

10. Notes 9

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

1. Introduction

Your Bristan dual control shower fitting is a thermostatic mixer incorporating a wax

capsule thermostat to ensure constant showering temperatures.

This valve has been designed to comply with BS EN 1287:1999 & BS EN1111:1999.

Manufactured to the highest quality standards.

These instructions are for your guidance to a safe and successful installation and should

be left with the user.

All products manufactured and supplied by Bristan are safe provided they are installed,

used correctly and receive regular maintenance in accordance with these instructions.

2. Specification

Inlet Connections: 15mm compression with 150mm between centres.

Water Pressures: Min. 0.3 bar Max. 5 bar Maximum recommended imbalance

between hot and cold supply should not exceed a ratio of 5:1

Maximum Outlet Temp: Factory Set to 38°C at the safety click and 48°C at the final stop

(can be re-set to suit site conditions).

Hot & Cold Supply Temperature

Maximum Cold supply:

25°C

Minimum recommended hot supply:

60°C

Maximum Hot Supply:

80°C

Note: the inlet hot water temperature must be at least 10°C above the required blend

temperature.

3. Pack Contents Check List

1 x Shower Valve

4 x Screws

4 x Wall Plugs

2 x Wall Pate

2 x 15mm Olives

2 x Fixing Bridge

2 x Shroud

2 x Filter Washer

4. Installation

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

4.1 Pre-Installation (See Fig. 1a & 1b)

4.1.1 Identify all components and check for completeness, particularly before arranging

fitting.

4.1.2 This mixer should be installed in compliance with Water Regulations. For further

details contact your Local Water Authority.

4.1.3 This mixing valve is suitable for use with the following systems:

• Gravity Fed Hot & Cold (Equal Pressure)

• Gravity Fed Hot & Mains Cold (Differential Pressure Maximum Ratio 5:1)

• Un-vented Systems

• Thermal Store Systems

• Gas Combination Boiler

• Pumped System

PLEASE NOTE:

On gravity systems the minimum distance from the underside of the cold-water storage

tank to the shower head must be at least 1 metre.

4.1.4 Before fitting the fast fit wall fixings, water should be flushed through the system

to remove all debris from the pipe work.

Fig. 1a

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

4.2 Installation

Prior to drilling into walls, check there are no hidden electrical wires, cables or water

supply pipes with the aid of an electronic detector. If you use power tools do not forget:

• Wear eye protection

• Unplug equipment after use

4.2.1 Fast Fit Fixing Kit (See Fig.1a)

4.2.1.1 Identify all components and check for completeness, particularly before

arranging fitting.

NOTE: - THE fixing centres are a NOMINAL DISTANCE of 150mm, therefore before drilling

holes for the supply pipes check the centre dimension of the actual product to be used.

4.2.1.2 Inlet pipes need to terminate with at least 30mm of 15mm diameter pipe (not

supplied) protruding through the finished wall surface.

Important:- Water supplies to the mixer must be with the Hot on the left, & Cold on the

right when viewed from the front .

4.2.1.3 Place the wall plate (2) over the pipe and mark the hole centres, drill two holes

to suit the wall plugs (1) and insert the wall plugs into the freshly drilled holes in the

wall.

4.2.1.4 Place the wall plate (2) with onto the wall and tighten up the screws until

secure. Place the olive (3) onto the protruding 15mm pipe. The pipe needs to protrude

past the olive by 5mm maximum.

4.2.1.5 Screw the fixing bridge (4) onto the wall plate (2) using a 22mm a/f spanner,

holding the wall plate (2) with the flats provided with a 47mm spanner – DO NOT

tighten up the fixing bridge (4) against the fixings (1).

4.2.1.6 Screw shroud (5) onto fixing bridge (4).

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

Fig. 1b

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

4.2.2 Bar Shower Body (See Fig. 1b)

To fit mixer body to the wall. Place the filter washers (6) into the connecting nuts (7)

and tighten to the fixing bridge (4 on page 3. Fig. 1a) using the connecting nuts (7)

which are secured to the mixer body.

5. Setting

5.1 The maximum temperature (beyond the 38°C click) can be adjusted to suit site

conditions or user preference. To adjust this, follow this procedure:

5.2 Position the temperature control handle to click stop point and turn on the flow

handle control handle letting the water run long enough to ensure that the hot water

supply is at its maximum temperature.

5.3 The shower has been factory set to 38oC at the click position with balanced supply

pressures of 0.5 Bar.

5.4 Whilst the water is flowing remove the temperature control handle (10) and shroud

(12), by pulling the handle off the spline adaptor (11).

5.5 Turn the spline adaptor (11) until the required maximum temperature is achieved

(the spline adaptor many need to be reposition to allow the head to line backup with

the body of the shower), anti-clockwise to increase the temperature and clockwise to

reduce it.

5.6 Important: Refit the shroud and handle and shroud so that the stop pin in the handle

(10) fits inside the rim of the white nylon stop ring (15).

5.7 Push the shroud (12) and handle back on and turn clockwise. The handle should

click. This is quite normal.

5.8 Turn off the flow at the flow control handle.

6. Operation

6.1 On / Off - Flow Control

There are two control handles on the shower. Turn the flow control handle (left)

anti-clockwise to turn on and increase the flow, and clockwise to decrease and turn off.

The temperature control handle (right) is turned anti-clockwise for hot, clockwise for

cold and features a ‘temperature click notch’. The ‘click’ is factory set to 38oC, but can be

over ridden by turning the handle anticlockwise past the click stop position.

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

7. General Fault Diagnosis

7.1 If your valve fails to function correctly, the following should be checked:

7.1.1 Check that the hot and cold connections are the correct way around. Hot on the

left, cold on the right when viewed from the front.

7.1.2 Ensure that the hot water temperature is adequate. The recommended minimum

temperature is 60°C.

7.2 If your shower will not turn off:

7.2.1 Check ceramic disc valve is free of debris.

7.3 If your shower has a low flow rate.

7.3.1 Check that the filters (6) are not blocked.

8. Cleaning & Maintenance

8.1 Cleaning

Your fitting has a high quality finish and should be treated with care to preserve the

visible surfaces.

All surface finishes will wear if not cleaned correctly, the only safe way to clean your

mixer is to wipe with a soft damp cloth. Stains can be removed using washing up liquid.

All bath cleaning powders and liquids will damage the surface of your fitting, even the

non-scratch cleaners.

8.2 Regular Maintenance

We advise that the valve is regularly serviced, particularly in hard water areas. It is also

important to clean the handset regularly in hard water areas to maintain an even

spray/flow of water.

NOTE: ISOLATE THE WATER SUPPLY TO THE SHOWER VALVE.

8.3 Cartridge Removal (See Fig. 1b)

8.3.1 Remove the temperature control handle (10) and shroud (12), by pulling the

handle off the spline adaptor (11).

8.3.2 Unscrew the cartridge (13) anticlockwise.

8.4 Cartridge Maintenance

8.4.1 Place the cartridge in a bowl and carefully add some hot water (just off the boil)

and vinegar to de-scale the cartridge. Leave until the water has cooled.

8.4.2 Then remove the cartridge and rinse with clean water.

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

8.5 Refitting the Cartridge

8.5.1 Grease the seals with suitable silicon grease and carefully refit the cartridge into

the body.

8.5.2 Reset the maximum temperature and refit temperature handle

9. Guarantee & Registration

9.1 Guarantee

All products are manufactured to the highest standards and 5-year guarantee covers any

defect in manufacture.

Any part found to be defective during the above guarantee period will be replaced with-

out charge providing that the product has been installed in accordance with our instruc-

tions, used as intended and maintained/serviced as recommended.

In the unlikely event that any problems are encountered with this product’s perform-

ance on installation, you must obtain guidance/authorisation from our Customer Service

Department before any remedial action is taken and be able to supply proof and date of

purchase.

The guarantee excludes damage caused by accident, misuse or neglect and does not

cover the following:

Those components subject to wear and tear such as ‘O’ rings and washers etc,

• Damage caused by faulty installation,

• Damage caused by any waterborne debris,

• Damage caused by improper cleaning products,

• Damage caused by the use of non-Bristan parts,

• The product being used for a purpose other than intended.

The company reserves the right, in the event of a claim not covered by the guarantee,

to charge the claimant for parts and labour at current rates. This guarantee is given in

addition to and does not affect your statutory rights.

In the interests of continuous product development Bristan Limited reserve the right to

alter the specification as necessary.

9.2 Registration

To register your product with us please complete and return the enclosed registration

card.

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

10. Notes

For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan Jute JU BF C Bedienungsanleitung

Bristan

Bristan Body Jet JET2 C Bedienungsanleitung

Bristan

Bristan EF KIT PK Verdrahtungsschema

Bristan

Bristan BUZ2 SHXDIVCTFF C (D4) Verdrahtungsschema

Bristan

Bristan TFS 1 C Verdrahtungsschema

Bristan

Bristan SAF SHCDIV BLK (D1) Verdrahtungsschema

Bristan

Bristan CFC33 Bedienungsanleitung

Bristan

Bristan Cadet Verdrahtungsschema

Bristan

Bristan Joy care Montageanleitung

Bristan

Bristan WMNT11 C Montageanleitung

Bristan

Bristan AR2 SHXVOFF Montageanleitung

Bristan

Bristan HOU SHCDIV C (D7) Verdrahtungsschema

Bristan

Bristan Wine Easyfit Verdrahtungsschema

Bristan

Bristan JAVA J BSM E8 C Bedienungsanleitung

Bristan

Bristan Java Mini J MBAS C Bedienungsanleitung

Bristan

Bristan Manhattan MH SNK C Bedienungsanleitung

Bristan

Bristan Quest Deck Sink Mixer Verdrahtungsschema

Bristan

Bristan Rio RO 1/2 C Bedienungsanleitung

Bristan

Bristan AR2 SHXVOFF Verdrahtungsschema

Bristan

Bristan GLL RAPSNK4 C Bedienungsanleitung

Bristan

Bristan 1901 Bedienungsanleitung

Bristan

Bristan Artisan Verdrahtungsschema

Bristan

Bristan ELVIRA SHWR PK Montageanleitung

Bristan

Bristan Value VAL BSM C CD Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung