Bristan Buzz Verdrahtungsschema

Installation Instructions & User Guide

Please keep these instructions for future reference and request of replacement parts

Buzz Rigid Riser Bar Mixer

Contents Page

Important Safety Information 03

General Information 04

Specifications 05

Dimensions 06

Product Features 07

Installation Requirements 08-10

Installation 11-15

Operation 16

Setting 16

Maintenance 17-18

Troubleshooting 19-20

Notes 21

Guarantee 22-23

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed

This product with your enjoyment in mind. To ensure that it works to it’s full potential, it

needs to be fitted correctly. These fitting instructions have been created to give you all of the

Information you need and, if you need any further help, please do not hesitate to give us a call on

0844 701 6273.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are installed

correctly, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this shower valve safely you must

employ the services of an experienced qualified plumber.

•This shower valve needs to be installed in accordance with, and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Warning: Do not operate the shower valve if you suspect it is frozen. Do not site the

shower valve where it might be subjected to freezing conditions.

•Do not crush or kink the shower hose as this could damage the hose and cause leaks.

•Remove all packaging and check the contents for damage before starting installation.

•Warning: Before starting any installation please consider the following: before drilling

into walls, check that there are no hidden electrical wires, cables or water supply pipes.

This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to; - Wear eye protection

- Unplug equipment after use

•Fitting Isolating valves to the inlet feeds is required for ease of maintenance.

•Warning: Before installing the new shower valve it is essential that you thoroughly

flush through the pipework in order to remove any remaining swarf, solder, etc. Failure to

carry out this procedure could cause problems or damage to the workings of the shower

valve.

•It is recommended that when installing the shower valve, full access is provided for

servicing purposes.

•This shower valve must not be modified in any way as this will invalidate the guarantee.

General Information

This product satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999

and current bylaws and is designed to be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65ºC. A stored water

temperature of 60ºC is considered sufficient to meet all normal requirements and will minimise

the build up of lime scale in hard water areas

If the shower valve is installed at low pressure (tank fed), then the minimum distance from the

highest installed position of the shower valve to the underside of the cold tank should be at least

5 metres to ensure adequate performance.

This shower valve should be installed in compliance with the Water Regulations. For further

details contact you Local Water Authority.

Specifications

Inlet Connections: 15mm Compression with 150mm between centres.

Operating Pressure Range: Minimum. 0.5 bar, Maximum 5.0bar.

Maximum Static Pressure: 10.0bar.

Note: Nominally equal (balanced) inlet supply pressures are required for optimum performance.

If pressures are unequal, then a pressure reducing valve should be used.

Maximum recommended imbalance between hot and cold supply should not exceed a ratio of 5:1

Maximum Outlet Temperature: Factory pre-set to 38ºC with push button override to 46ºC (can

be re-set to suit site conditions or personal preference).

Supply Requirements:

Minimum cold water supply temperature: 5ºC

Maximum cold water supply temperature: 25ºC

Maximum hot water supply temperature: 80ºC

(a maximum hot water supply of 60-65ºC is recommended for ablutionary purposes).

Note: The inlet hot water temperature must be at least 10ºC above the required blend

temperature (e.g. outlet temperature 43ºC: Minimum hot supply 53ºC).

Dimensions

All dimensions are in mm’s and are approximate.

Product Features

1. Water Flow Control

Controls the amount of flow of water from

the showerhead.

Note: The Buzz shower valve has

an Eco feature. Press the button in

on the handle (1) and continue to turn

the handle for an increased flow rate.

2. Temperature Control

Adjustable temperature control.

The temperature control incorporates

a safety stop facility limiting the water

temperature to 38ºC.

To obtain a higher water temperature,

Press the button in on handle (2)

and continue to turn the control to the

desired temperature.

Cool Touch Feature

This shower valve incorporate a

cool touch feature. When the shower

valve is in use the body of the shower

will not get hot and will remain cool.

Installation Requirements

This shower valve must be installed in

compliance with current water regulations.

If you have any doubts about the water

regulation requirements contact your local

water services provider or use the services

of a professional plumber.

This shower valve is suitable for use with

the following water supply systems.

•Gravity Fed Hot and Cold

(pressure Balanced)

•Gravity Fed Hot and Mains Cold

(differential pressure – see Specification

section on page 5.

•Instantaneous Water Heater

(combination boiler)

•Unvented System

•Pumped System

Gravity Fed Hot and Cold

Important: If you install this shower

valve with a gravity fed system, there must

be a minimum head (vertical distance)

from the underside of the cold water

storage tank to the shower valve position of

at least 5 metres.

Note: Pumped system (with Essex

flange) If you install this shower valve to a

pumped gravity fed system where the

minimum head (vertical distance) from the

underside of the cold water storage tank to

the top of the hot water cylinder is less

than 1 metre we recommend an Essex

flange is used as shown on page 09.

Flushing Pipework

Important: Before connecting the

shower valve (see Installation on pages 12-

14), supply pipework must be flushed to

clear debris before connecting the shower

valve. Debris will reduce the performance

and life of the shower.

Gravity Fed Hot and Mains Cold

Cold mains supply Cold mains supply

2m min

min

Installation Requirements

Instantaneous Water Heater Unvented System

Pumped System Pumped System (with Essex flange)

Key: Isolating Reducing Shower Pump Essex

Valve Valve Valve Flange

Cold mains supply Cold mains supply

2m min 2m min

If less

than 1m

see note.

50mm

Installation Requirements

These fittings need to be installed in

accordance with the following Installation

Requirements and Notes (IRN) to ensure

they meet the requirements of the Water

Supply (Water Fittings) Regulations 1999

and the Scottish Byelaws 2004.

IRN R001: See text of entry for Installation

Requirements or Notes.

IRN R040 - Schedule 2-15 (1): The fitting

shall be installed so that its outlet discharges

above the spill-over level of any fixed appliance

as indicated below:-

For backflow protection in domestic or

installations up to, and including, Fluid

Category 3.

If the fitting cannot be installed as indicated in

the table opposite it shall be installed as either

a or bbelow:

a: with an approved double check valve

assembly or some other no less

effective backflow prevention device

immediately upstream of the inlet.

b: so that it draws water by gravity only from a

cistern, or cylinder having a

permanently open vent pipe, and the

distributing pipe supplies no other fitting

(other than draining tap) at a lower level.

For backflow protection in premises or

installations up to, and including Fluid

Category 5.

The vertical distance of the outlet above the

spill-over level shall be not less than 20mm or

twice the diameter of the inlet pipe to the

fitting, which ever is the greater. If the fitting

cannot be installed as indicated it shall be

installed with a backflow prevention

arrangement suitable for the Fluid Category.

Size of tap or

combination fitting.

Vertical distance

of outlet above

spill-over level.

1. Not exceeding 1/2

in 20mm

2. Exceeding 1/2 in

but not exceeding

3/4 in

25mm

3. Exceeding 3/4 in 70mm

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan PM2 SHCDIV C Verdrahtungsschema

Bristan

Bristan EXD BAS C Bedienungsanleitung

Bristan

Bristan K 1/2 C Verdrahtungsschema

Bristan

Bristan PIV BAS C Bedienungsanleitung

Bristan

Bristan Regency Luxury R BSM C Verdrahtungsschema

Bristan

Bristan TFS 1 C Verdrahtungsschema

Bristan

Bristan Value VAL BSM C CD Verdrahtungsschema

Bristan

Bristan JAVA J THBSMVO C Verdrahtungsschema

Bristan

Bristan KN2 SHXAR C Montageanleitung

Bristan

Bristan Z2 SQR 1/2 C Verdrahtungsschema

Bristan

Bristan WASTES W BATH09 C Verdrahtungsschema

Bristan

Bristan Artisan Verdrahtungsschema

Bristan

Bristan EV KIT-EFB C Montageanleitung

Bristan

Bristan JAVA J BSM E8 C Bedienungsanleitung

Bristan

Bristan Rio RO 1/2 C Bedienungsanleitung

Bristan

Bristan Body Jet JET2 C Bedienungsanleitung

Bristan

Bristan CR SHXDIVFF C (D7) Verdrahtungsschema

Bristan

Bristan W BATH07 C Verdrahtungsschema

Bristan

Bristan N2 SHC3STP G Verdrahtungsschema

Bristan

Bristan Z TC 1/2 C Bedienungsanleitung

Bristan

Bristan Star FH STRD01 C Bedienungsanleitung

Bristan

Bristan H64WMT2 Montageanleitung

Bristan

Bristan COB SHC3STP C (D9) Verdrahtungsschema

Bristan

Bristan PM2 SHCDIV BLK (D2) Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung