Bristan K SNKSL EF C Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Colonial Single Lever

Easyﬁt Sink Mixer

Model covered: K SNKSL EF C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 4

Dimensions............................................................................... 5

Installation Requirements ....................................................... 6

Installation................................................................................ 7-8

Operation .................................................................................. 9

Maintenance ............................................................................. 10

Troubleshooting........................................................................ 11

Notes......................................................................................... 12-13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This ﬁtting needs to be installed in accordance with, and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing the new ﬁtting it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the ﬁtting.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

• This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 8558.

BS 8558 recommends hot water should should be stored and distributed at a

temperature of not less than 60°C which will minimise the build up of limescale in hard

water areas.

If the ﬁtting is installed at low pressure (tank fed), then the minimum distance from the

highest installed position of the outlet to the underside of the cold tank should be at

least 2 metres to ensure adequate performance.

This tap should be installed in compliance with the Water Regulations. Where the

supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the mains,

approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Speciﬁcations

Operating pressure range (bar) Min Max

0.2 5.0

Maximum static pressure – 10.0 bar

Inlet Connections: M10 1/2" BSP Flexible Tails with Isolation Valves

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are nominal and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

280

298

225

G1/2”

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household pipework to

ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

Isolation Valves

The isolation valves must be accessible with a suitable ﬂat-blade screwdriver for turning

on and for future servicing purposes.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Closed / Off

position

Open / On

position

Installation

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

1. Fit push-ﬁt connector

Place the ‘push-ﬁt connector’ into the hole in the

basin top. Ensure the rubber washer is ﬁtted to

the underside.

2. Attach hot and cold connectors

Position the backnut under the basin (with the

rubber seal on top), ensuring the locating pin ﬁts

into the hole in the backnut. Insert and loosely

tighten the threaded cold connector by turning the

6mm hexagonal key clockwise.

Once threading has started you can let go of the

backnut. Before fully tightening the cold

connector, place the ‘hot connector’ into the

push-ﬁt connector - ensure it ﬁts fully through the

basin hole.

Note: The hot connector has 2 ﬂat edges at the top

to allow it to ﬁt fully down and close to the top of

the cold connector. Failure to do this may prevent

the tap ﬁtting onto the connector.

Important: The push-ﬁt connector must be

fully tightened to the back nut before attaching the

ﬂexible connecting pipes.

connector

Rubber

washer

6mm

hexagonal

key

Backnut with

rubber seal

Under

the

basin

Cold

connector

Hot

connector

Locating

Installation Cont.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

3. Attach ﬂexible connecting pipes.

Important: Before connecting the ﬂexible

connecting pipes, please refer to the speciﬁc

installation requirements on page 6.

Carefully screw the ‘ﬂexible connecting pipes’ into

the ‘push-ﬁt connectors’. Fit the isolation valves

(supplied) to the ﬂexible connection pipes and turn to

the 'closed' position as shown on page 6.

Note: A ﬂexible connecting pipe can be fed up

through the hot connector hole and then screwed on

if required.

Important: Only tighten the ﬂexible connecting

pipe by hand. Do not overtighten. Connect the

isolation valves/ﬂexible connecting pipes to the

household water supply pipes.

4. Cover cap

If required place the cover cap over the push-ﬁt

connector until the tap body is ready to be ﬁtted.

5. Fit the tap body

Remove the cover cap and place the plinth over the

push-ﬁt connector. Grease the push-ﬁt connector

using the sachet of grease provided. Push-ﬁt

the tap body onto the connector. Align the body and

tighten the grub screw at the rear of the body, using

the long end of the 2.5mm hexagonal key as shown

below until ﬁnger tight. Remove the hexagonal key

and insert the short end into the grub screw and

tighten an extra ¾ to 1 complete turn more to ensure

the tap body is securely tightened to the push-ﬁt

connector.

Important: The ﬁtting must be securely attached

to the base.

Turn on the mains water supply and open the

isolating valves using a suitable ﬂat blade

screwdriver. (See page 6)

Tap body may vary to the one shown

here

Cover cap

Flexible

connecting

pipes

Hot

connector

2.5mm

hexagonal key

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Operation

Off

Hot Cold

Temperature Control

Flow Control

Maintenance

Your ﬁtting has a high quality ﬁnish and

should be treated with care to preserve

the visible surfaces. All surfaces will

wear if not cleaned correctly, the only safe

way to clean your mixer is to wipe with a

soft damp cloth. Stains can be removed

using washing up liquid. All bath cleaning

powders and liquids will damage the

surface of your ﬁtting, even the

non-scratch cleaners.

Note: Never use abrasive detergents or

disinfectants or those containing alcohol,

hydrochloric acid or phosphoric acid.

Before carrying out any maintenance, turn

off the mains water supply and close any

isolating valves.

Unscrew the handle lever and loosen the

grub screw. Remove the handle.

Remove the shroud, cartridge retaining

and the cartridge.

Clean the cartridge thoroughly under cold

water to remove any build up of limescale

or debris.

If necessary replace the cartridge using

parts supplied by Bristan only.

Replace the cartridge, cartridge retaining

nut and the shroud. Replace the handle,

tighten the grub screw and screw the

handle lever back in.

Cleaning the Cartridge

General Cleaning

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Grub

Screw

Handle

Handle Lever

Cartridge

Retaining Nut

Shroud

Tap Body

Cartridge

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan EF KIT PK Verdrahtungsschema

Bristan

Bristan PIV BSM C Bedienungsanleitung

Bristan

Bristan W SNK6 C Bedienungsanleitung

Bristan

Bristan Regency Luxury R BSM C Verdrahtungsschema

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan VAL2 BRDSM C CD Verdrahtungsschema

Bristan

Bristan WASTES W BASIN04 BB Montageanleitung

Bristan

Bristan BUZ2 SHXDIVCTFF C (D4) Verdrahtungsschema

Bristan

Bristan Java J BID C Bedienungsanleitung

Bristan

Bristan Opac Series Montageanleitung

Bristan

Bristan CRZ2 SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan VAL2 BAS C CD (D2) Verdrahtungsschema

Bristan

Bristan Quadrato Tap Range Verdrahtungsschema

Bristan

Bristan Blade BL BAS C Bedienungsanleitung

Bristan

Bristan Mios MIO BSM C Verdrahtungsschema

Bristan

Bristan IRN R001 Bedienungsanleitung

Bristan

Bristan VR1000 Bedienungsanleitung

Bristan

Bristan DSC SHC3DIV C Verdrahtungsschema

Bristan

Bristan VAL2 BIB C 6 CD Verdrahtungsschema

Bristan

Bristan Java J BF C Bedienungsanleitung

Bristan

Bristan Regency R BSM C Bedienungsanleitung

Bristan

Bristan W BTH12 C Bedienungsanleitung

Bristan

Bristan SAI 1/2 C Montageanleitung

Bristan

Bristan H64WMT2 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung