C.A. Technologies Jaguar SLP Bedienungsanleitung

HVLP AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

STANDARD

IN CAT

PACK

AVAILABLE FLUID

NOZZLES TIPS

NEEDLES /

marking on needle

23-1308 33-0208 0.8mm (.022") 40-1308 (308)

23-1310 W, W-PPS 33-0210 1.0mm (.040") 40-1310 (310)

23-1312 33-0212 1.2mm (.046") 40-1312 (312)

23-1313 W, A, PPS 33-0213 1.3mm (.052") 40-1313 (313)

23-1314 33-0214 1.4mm (.055") 40-1314 (314)

23-1315 W, A, PPS 33-0215 1.5mm (.059") 40-1315 (315)

23-1317 33-0217 1.7mm (.070") 40-1317 (317)

23-1319 W, A, PPS 33-0219 1.9mm (.075") 40-1319 (319)

23-1322 33-0222 2.2mm (.086") 40-1322 (322)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

W = Wood

*Note: Air cap test gages are available to confirm HVLP compliance.

A = Automotive

*Gun inlet pressures may vary as required by application PPS = 3M™ PPS™

Jaguar

SLP

(JSLP)

60-1504 (S) 13.529*

GRAVITY FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Jaguar SLP

Operation and Maintenance Instructions for

JSLP

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Screw the paint cup onto the gun’s gravity feed fluid inlet.

3.Fluidflowcan be controlled usingthefluidcontrolknob, thisrestricts flowbylimitingneedletravel.Itisbest tocontrol

fluid flow byproper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenanceis essential toinsure proper gunoperation.

Severalstatesprohibitsprayingsolvent intothe atmosphere and requirethe use ofcoveredgun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Removeair cap andclean separatelyusingcleansolvent.

Clean the gravityfeed cup thoroughly, then spray clean solvent through the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Haverepairkit#10-105availablebefore gundisassembly.

Gun head disassembly

Toremove thenozzle carrier (5) and aircap adapter (7):

1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body(3), and needle (16).

2.Remove theneedlesealcartridge(17).

3. Loosenthe locknut (11) andremove fluid inlet(12) using a 11/16” open-endwrench.

4. The nozzle carrier (5) and air cap adapter (7) will now slide forward from the gun body (13).

Gun head reassembly

1. Install a new o-ring (4 & 8) on the air cap adapter (7).

2. Install the thread locknut (11) and seal (10) onto the fluid inlet (12) as far as possible.

3. Install a new fluid inlet seal (9) into the recess area on the nozzle carrier (5) inlet port.

4. Install carrier seal (6) onto the back of the nozzle carrier (5).

5. Slide the nozzle carrier (5) into air cap adapter (7) and insert into the gun body (13) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (17) but do not tighten.

6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (12) and tighten firmly.

7. Tighten the needle seal (17) to approx. 12 ft.-lb. torque.

8. Tighten the fluid inlet (12) to approx. 25 ft.-lb. torque.

9. Tighten the locknut (11) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION

1See Air Cap Chart Air Cap** 19 60-2101 Trigger

2See Air Cap Chart Fluid Tip** 20 60-1520 Air Valve Assembly

333-1202 Fluid Nozzle Body 21 60-302 Air Valve Poppet

4 98-8026 O-Ring* 22 60-125 Seal*

560-J31H Nozzle Body Carrier 23 61-1003 Air Valve Spring*

6 60-123 Seal* 24 60-119 Seal*

760-34H Air Cap Adapter 25 60-201 Rear Bushing

860-131 O-Ring* 26 60-204 Needle Return Spring*

9 60-124 Seal* 27 60-205 Spring Seat*

10 60-130 Seal* 28 60-202 Fluid Control Knob*

11 60-118 Locknut 29 60-1510 Inlet Air Control (Optional)

12 60-127 Fluid Inlet 30 60-122 Plug

13 60-1119 Jaguar Gun Body SLP 31 60-104 Air Inlet Fitting

14 98-0109 Allen Plug 51-401 Standard 700 mL Gravity Feed Cup (Aluminum)

15 See Air Cap Chart Fan Control Assembly** 51-400 Optional 700 mL Gravity Feed Cup (Plastic)

16 See Air Cap Chart Fluid Needle** 51-403 Optional 1000 mL Gravity Feed Cup (Aluminum)

17 60-1400 Needle Seal* 51-418 Gravity Cup Lid (401 & 403)

18 60-1033 Trigger Pivot Set 51-413 Gravity Cup Lid (400)

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-105

HVLP AIR CAP TEST GAGES

23-1308-G

23-1310-G

23-1312-G

FOR

JSLP

GUNS

23-1313-G

23-1314-G

23-1315-G

23-1322-G

23-1317-G

23-1319-G

JSLP HVLP SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH CFM

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

13.5

1.3 mm x 1313

1.5 mm x 1315

1.7 mm x 1317

13.5

1.5 mm x 1315

1.7 mm x 1317

1.9 mm x 1319

2.2 mm x 1322

13.5

FLUID NOZZLE / AIR CAP SELECTION CHARTS

JAGUAR SLP Series - Gravity Feed Guns

1.0 mm x 1310 12 13.5

1.0 mm x 1310

1.3 mm x 1313 12

Revised1/7/16

CP-JSLP-PPS

CP-JSLP

EP-JSLP-(W or A) Includes:

51-401 700 mL Aluminum Gravity Cup

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

EP-JSLP-(W or A)-PPS Includes:

91-465 650 mL PPS™ Cup and Collar

91-466 Lids and Liners (Available in 50 Pack)

91-474 #2 PPS Adapter

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-JSLP-(W or A) Includes:

51-401 700 mL Aluminum Gravity Cup

52-300 Mini Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

51-430 Gravity Gun Hook

Air Caps and Needles Shown on Page 1

CP-JSLP-(W or A)-PPS Includes:

91-465 650 mL PPS™ Cup and Collar

91-466 Lids and Liners (Available in 50 Pack)

91-474 #2 PPS Adapter

52-300 Mini Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

Andere C.A. Technologies Spritzpistole Handbücher

C.A. Technologies

C.A. Technologies CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx L100C Bedienungsanleitung

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 300C Fehlerbehebungshandbuch

C.A. Technologies

C.A. Technologies TOMCAT 100C Fehlerbehebungshandbuch

C.A. Technologies

C.A. Technologies Jaguar 300H Bedienungsanleitung

C.A. Technologies

C.A. Technologies CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 100G 1590 Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100 Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx L200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Techline JR Bedienungsanleitung

C.A. Technologies

C.A. Technologies Jaguar 100 Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies AutoCAT 300C Bedienungsanleitung

C.A. Technologies

C.A. Technologies CAT SLP Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies LYNX L100CM Handbuch

C.A. Technologies

C.A. Technologies Tomahawk TG Bedienungsanleitung

C.A. Technologies

C.A. Technologies H2O-CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies CAT-Xpress Fehlerbehebungshandbuch

C.A. Technologies

C.A. Technologies Cougar Bedienungsanleitung

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 100G Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 200Z Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung