Canon EF11-24mm f/4L USM Bedienungsanleitung

EF11-24mm f/4L USM

Instructions

ENG

COPY

ENG-1

Thank you for purchasing a Canon product.

Canon’s EF11-24mm f/4L USM is a high-

performance ultra-wide angle zoom lens, for use

with EOS cameras.

● “USM” stands for Ultrasonic Motor.

Features

1. Use of super UD lens elements, UD lens

elements, and two types of aspherical lens

elements giving superior denition.

2. SWC (Subwavelength Structure Coating)

and ASC (Air Sphere Coating) are utilized to

signicantly reduce occurrences of are and

ghost created by quite large incident angles of

light.

3. Using a uorine coating on the foremost and

rearmost lens surfaces allows adhered dirt to be

removed more easily than before.

4. Ultrasonic motor (USM) for fast, quiet autofocus.

5. Manual focusing is available after the subject

comes into focus in autofocus mode (ONE

SHOT AF).

6. Circular aperture for producing beautiful

softfocus images.

7. Tight seal structure provides excellent dustproof

and drip-proof performance. However, it is

unable to provide complete protection from dust

and moisture.

COPY

ENG-2

Safety Precautions

● Do not look at the sun or a bright light source

through the lens or camera. Doing so could result in

loss of vision. Looking at the sun directly through the

lens is especially hazardous.

● Whether it is attached to the camera or not, do not

leave the lens under the sun without the lens cap

attached. This is to prevent the lens from concentrating

the sun’s rays, which could cause a re.

● The EF11-24mm f/4L USM features a large diameter

front lens element. Please be careful because this

large front section will extend past the bottom of some

cameras.

Conventions used in this instruction

Warning to prevent lens or camera malfunction

or damage.

Supplementary notes on using the lens and

taking pictures.

Handling Cautions

● If the lens is taken from a cold environment into a

warm one, condensation may develop on the lens

surface and internal parts. To prevent condensation

in this case, rst put the lens into an airtight plastic bag

before taking it from a cold to warm environment. Then

take out the lens after it has warmed gradually. Do the

same when taking the lens from a warm environment

into a cold one.

● Do not leave the lens in excessive heat such as in a car

in direct sunlight. High temperatures can cause the

lens to malfunction.

Usage Precautions

● When using this lens, please check the Canon website

for the latest camera rmware. If the camera’s rmware

is not the latest version, be sure to update to the latest

rmware.

● For details on updating rmware, please check the

Canon website.

COPY

ENG-3

Precautions for Shooting

● If dirt or dust adheres to the surface of the front lens element, it can easily appear in images due to the

lens’s short focal length. In order to avoid this, please remove dirt or dust from the surface of the front lens

element by using a commercially available air dust blower.

● Since this lens has a wide angle of view, light from bright light sources, such as the sun, can easily enter

the image area. Please do not look at bright light sources using the camera’s viewnder.

● Similarly, are and ghost will occur when bright light sources appear in the image area, depending on

shooting conditions. In order to prevent are and ghost, we suggest shooting places such as shaded are

as so that bright light does not enter the lens.

COPY

ENG-4

This device complies with Part

15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Do not make any changes or modications to the equipment

unless otherwise specied in the instructions. If such

changes or modications should be made, you could be

required to stop operation of the equipment.

This equipment has been tested and found to comply with

the limits for a class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Safety Precautions

CAN ICES-3 (B) / NMB-3 (B)

COPY

ENG-5

Nomenclature

● For detailed information, reference page numbers are provided in parentheses (→**).

Focus mode switch (→ 7)

Distance scale (→ 8)

Zoom ring (→ 7)

Rubber ring (→ 6)

Gelatin filter holder (→ 9)

Contacts (→ 6)

Lens mount index (→ 6)

Focusing ring (→ 7)

Built-in lens hood

COPY

ENG-6

1. Mounting and Detaching the Lens

See your camera’s instructions for details on

mounting and detaching the lens. The lens mount has a rubber ring for enhanced

dust- and water-resistance. The rubber ring may

cause slight abrasions around the camera’s lens

mount, but this will not cause any problems. If the

rubber ring becomes worn, it is replaceable by a

Canon Service Center at cost.

● After detaching the lens, place the lens with

the rear end up to prevent the lens surface and

contacts from getting scratched.

● If the contacts get soiled, scratched, or have

ngerprints on them, corrosion or faulty

connections can result. The camera and lens

may not operate properly.

● If the contacts get soiled or have ngerprints on

them, clean them with a soft cloth.

● If you remove the lens, cover it with the dust

cap. To attach it properly, align the lens mount

index and the index of the dust cap as shown

in the diagram, and turn clockwise. To remove it,

reverse the order.

Please be careful when laying the lens

sideways. The lens may roll and fall, resulting

in injury.

COPY

ENG-7

Setting the Focus Mode

Zooming

After autofocusing in ONE SHOT AF mode, focus

manually by pressing the shutter button halfway

and turning the focusing ring. (Full-time manual

focus)

To shoot in autofocus (AF) mode, set the focus

mode switch to AF.

To shoot in manual focus (MF) mode, set the

focus mode switch to MF, and focus by turning

the focusing ring.

The focusing ring always works, regardless of

the focus mode.

To zoom, rotate the zoom ring.

Also, the minimum focusing distance of the lens

changes depending on focal length.

Focal Length

(mm) Min. Focusing

Distance (m/ft) Magnication (×)

11 0.32 / 1.05 0.06

16 0.29 / 0.95 0.10

24 0.28 / 0.92 0.16

● Be sure to nish zooming before focusing.

Zooming after focusing can affect the focus.

● Zooming in causes the front lens assembly to

extend along the lens’s optical axis. This adds

to the weight of the lens assembly, so pointing

it up or down when zooming in may increase or

decrease the torque felt in the zoom ring.

COPY

ENG-8

InnityCompensation

Mark

For accurate manual focusing of subjects at innity,

look through the viewnder or look at the magnied

image* on the LCD screen while rotating the

focusing ring.

To compensate for shifting of the innity focus

point that results from changes in temperature,

there is a margin at the innity (∞) position.

The innity position at normal temperature is the

point at which the vertical line of the distance

scale L mark is aligned with the distance index.

Distance index

Innity compensation

mark

* For cameras with Live View shooting capability.

5. Infrared Index

● The infrared index position is based on a

wavelength of 800 nm.

● The compensation amount differs depending on

the focal length. Use the indicated focal length

as a guide when setting the compensation

amount.

● Be sure to observe the manufacturer’s

instructions when using infrared lm.

● Use a red lter when you take the picture.

Some EOS cameras cannot use infrared lm. See

the instructions for your EOS camera.

The infrared index corrects the focus setting

when using monochrome infrared lm. Focus on

the subject manually, then adjust the distance

setting by moving the focusing ring to the

corresponding infrared index mark.

COPY

ENG-9

6.Lens Cap

The lens cap can be attached by pinching the

lock knobs and vertically aligning the lens cap

with the lens hood as shown in the diagram.

There is a gelatin filter holder at the rear of the

lens. Cut the gelatin filter to fit within the white

frames. Then insert the gelatin filter into the filter

holder.

7.Filter (Sold separately)

The recessed sections of the lens hood that the

cap locks on to are located at the front inside edge

of the top and bottom petals.

Lock knobs

The lens’s rear lens group moves back toward the

rear of the lens (camera side) the most when the

lens is set to the wide end. Therefore, in order to

prevent the rear lens element from making contact

with a lter (when installed), we recommend using

a lter only if the zoom ring is not set to the wide

end.

COPY

Inhaltsverzeichnis

Andere Canon Kameraobjektiv Handbücher

Canon

Canon KT17ex4.3B IRSE Bedienungsanleitung

Canon

Canon FD Lens Bedienungsanleitung

Canon

Canon digi super 86 XS Bedienungsanleitung

Canon

Canon EF 50mm 1:1.0L Bedienungsanleitung

Canon

Canon TL-30.5 Bedienungsanleitung

Canon

Canon IMAGE STABILIZER ULTRASONIC EF300MM f/4L IS... Bedienungsanleitung

Canon

Canon EF 100mm f/2.8L MARCO IS USM Bedienungsanleitung

Canon

Canon HJ17ex7.6B IRSE A Bedienungsanleitung

Canon

Canon EF 70-200mm f/2.8L IS II USM Bedienungsanleitung

Canon

Canon EF500mm f/4L IS II USM Bedienungsanleitung

Canon

Canon KJ17ex7.7B Bedienungsanleitung

Canon

Canon EF 40mm f/2.8 STM Bedienungsanleitung

Canon

Canon 9519B008AA Bedienungsanleitung

Canon

Canon EF 200mm 1:1.8 L USM Bedienungsanleitung

Canon

Canon EF50mm f/1.0L USM Bedienungsanleitung

Canon

Canon MP-E 65 mm 1:2.8 1-5x Bedienungsanleitung

Canon

Canon 4318C002 Bedienungsanleitung

Canon

Canon TS-E 24mm 1:3.5 L Bedienungsanleitung

Canon

Canon EF 400mm f/2.8L IS II USM Bedienungsanleitung

Canon

Canon EF 70-300mm f/4.5-5.6 IS USM Bedienungsanleitung

Canon

Canon RF 200-800mm F6.3-9 IS USM Bedienungsanleitung

Canon

Canon EF 100-400mm f/4.5-5.6L IS USM Bedienungsanleitung

Canon

Canon EF-S55-250mm f/4-5.6 IS II Bedienungsanleitung

Canon

Canon EF24-70mm f/2.8L USM Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung

Nikon

Nikon AF-S Zoom-Nikkor 17-35mm f/2.8D IF-ED Bedienungsanleitung

Samsung

Samsung Samsung 18-55mm Bedienungsanleitung