Canon Creative Park Easter Bunny Egg Holder Bedienungsanleitung

Easter : Bunny Egg Holder : Assembly Instructions ©

Canon Inc. ©

Taka Taka

Assembly Instructions

Mountain fold(dotted line)

Make a mountain fold.

Valley fold(dashed and dotted line)

Make a valley fold.

Scissors line(solid line)

Cut along the line.

Cut in line(solid line)

Cut along the line.

Glue spot(Red dot)

Glue parts with the same number together.

Glue spot(Green dot)

Glue within the same part.

Glue spot(Blue dot)

Glue to the rear of the other part.

Glue

The glue spot(colored dot)

shows where to apply the glue.

Tools and materials

Assembly tip

Caution

Scissors, set square, glue(We recommend stick glue), pencil, used

ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valley

fold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young children

so be sure to keep them out of the reach of young children.

View of completed model

Assembly Instructions : Three A4 sheets (No. 1 to No. 3)

*Hint: Trace along the folds with a ruler

and an exhausted pen (no ink) to get a sharper, easier fold.

* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

Before starting assembly :

Writing the number of each section on its back side before

cutting out the sections is highly recommended.

(* This way, you can be sure which section is which even

after cutting out the sections.)

Indicates where sections should

be glued together.

We recommend using Matte Photo Paper and wood glue.

Assembling the Easter Bunny

Glue the inside

surfaces of parts

1-4 and 1-5.

Glue here

Easter : Bunny Egg Holder : Assembly Instructions ©

Canon Inc. ©

Taka Taka

Assembling the ribbon Assembling the lid

Wrap this part around a round

pencil or other such cylinder to make

it assume a curve.

Glue the rear sides of the dots first.

Glue the ribbon to the Easter Bunny.

Assemble three units of part 3-1.

Glue the rear side of part 3-3.

Glue the bottom surface first.

Glue part 3-4 into place after inserting

parts 3-1 into part 3-2.

The lid is complete!

Assembling the egg holders (three in all)

The egg holders differ in color only.

Each is assembled in the same way.

Apply a curve to this

piece in the same way

as with the ribbon, then

glue its ends together.

Glue each glue tab to

the interior of the stand,

one tab at a time.

The egg stand

is complete!

Assembling the chicks (three in all)

Although the shapes and illustrations of

each chick differ slightly,

each one is assembled in the same way.

Easter : Bunny Egg Holder : Assembly Instructions ©

Canon Inc. ©

Taka Taka

Assembling the Easter eggs (six pieces in all : three lids and three bases) Arrange the Easter Bunny box, the egg holders, the Easter eggs, and the chicks in

the way you find most pleasing. You can also use this model to hold real Easter eggs.

Although parts 6-1 and 6-2 differ in size and pattern, the assembly method is the same.

Glue each spot firmly, one spot at a time.

Glue each tab to the interior

of the egg, one tab at a time,

as shown in the illustration.

The Easter egg is complete!

Andere Canon Spielzeug Handbücher

Canon

Canon Grand Piano Bedienungsanleitung

Canon

Canon Creative Park Kissing Dolls Bedienungsanleitung

Canon

Canon CREATIVE PARK New Baby Bedienungsanleitung

Canon

Canon CREATIVE PARK (Moving) Clowns spinning... Bedienungsanleitung

Canon

Canon Creative Park Ferret Bedienungsanleitung

Canon

Canon Thoroughbred Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

Canon

Canon CREATIVE PERK Elastic-powered Bus : Pattern Bedienungsanleitung

Canon

Canon Creative Park Cube Perpetual Calendar Monkey Bedienungsanleitung

Canon

Canon Creative Park Leaping Goat Pattern Bedienungsanleitung

Canon

Canon CREATIVE PARK Komatsu Special Vehicle 04... Bedienungsanleitung

Canon

Canon Creative Park Shaky-Shaky Maracas Bedienungsanleitung

Canon

Canon Creative Park Church of the Transfiguration Bedienungsanleitung

Canon

Canon Nippon Maru Bedienungsanleitung

Canon

Canon CREATIVE PARK Yajirobe Bedienungsanleitung

Canon

Canon Creative Park Pomeranian Bedienungsanleitung

Canon

Canon CREATIVE PARK Lion Dance Bedienungsanleitung

Canon

Canon Creative Park Crocodile Bedienungsanleitung

Canon

Canon PAPER CRAFT Pop-up Card Birdcage Bedienungsanleitung

Canon

Canon Creative Park Miniature Pig Bedienungsanleitung

Canon

Canon CREATIVE PARK Mobile Sky and Sea Bedienungsanleitung

Canon

Canon Viva! Welcome to Circusland! Bedienungsanleitung

Canon

Canon Creative Park Performing white horses Bedienungsanleitung

Canon

Canon Creative Park Football Money Box Kurzanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung