Car-Interface CI-RL2-SC14 Bedienungsanleitung
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
r.LiNK Video-inserter
CI-RL2-SC14
Compatible with
Volvo vehicles with Sensus Connect Infotainment and internet button
with 7 inch monitor
Video-inserter for rear-view camera
and two additional video sources
Product features
Video-inserter for factory-infotainment systems
2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner)
FBAS Rear-view camera video-input
Automatic switching to rear-view camera input on engagement of the reverse gear
Activatable parking guide lines for rear-view camera (not for all vehicles)
Picture-in-picture (PIP) mode combining after-market rear-view camera picture
with factory parking sensor graphic (not for all vehicles)
Video-in-motion in drive mode (ONLY for connected video-sources)
Video-inputs NTSC and PAL compatible
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page2
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
1.3. Connectors –video interface
1.4. Dip-switch settings
1.4.1. Enabling the interface’s video inputs (dip 2-3)
1.4.2. Rear-view camera setting (dip 5)
1.4.3. PDC car setting (dip 8)
2. Installation
2.1. Place of installation
2.2. Connection schema
2.3. Connecting - PNP power / CAN cable
2.3.1. Exchange of Quadlock chambers
2.4. Analogue connecting - video-interface
2.5. Connection –picture signal cable
2.6. Connecting video sources
2.6.1. After-market rear-view camera
2.6.1.1. Case 1: CAN-box receives the reverse gear signal
2.6.1.2. Case 2: CAN-box does not receive the reverse gear signal
2.6.2. Audio-insertion
2.7. Connecting video-interface and keypad
2.8. Picture settings and guide lines
3. Interface operation
3.1. By infotainment buttons
3.2. By external keypad
4. Specifications
5. Frequently asked questions
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page3
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation.
Technical knowledge is necessary for installation. The place of installation must be free of
moisture and away from heat sources.
1.1. Delivery contents
Take down the serial number of the interface and store this manual for support
purposes: ____________________
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page4
Requirements
Brand
Compatible vehicles
Compatible systems
Volvo
Vehicles since model year 2014
Sensus Connect with 7 inch monitor and
internet button.
Limitations
Video only The interface inserts ONLY video signals into the infotainment. For inserting
Audio signals either the possibly existing factory audio-AUX-input or a FM-
modulator can be used. If 2 audio sources shall be connected to the
infotainment, an additional electronic is necessary to switch them.
Guide lines / PDC If the CAN-box does not receive the required information from the vehicle CAN-
bus, neither guide-lines nor PDC will be supported.
Factory rear-view camera Automatically switching-back from inserted video to factory rear-view camera is
only possible while the reverse gear is engaged. To delay the switch-back an
additional electronic part is required.
1.2. Checking the compatibility of vehicle and accessories
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page5
1.3. Connectors –video interface
The video-interface converts the video signals of connected after-market sources in a factory
monitor compatible picture signal which is inserted in the factory monitor, by using separate
trigger options.
1.4. Dip-switch settings
Some settings must be selected by the dip-switches on the
video-interface. Dip position down is ON and position up is OFF.
After each Dip-switch-change a power-reset of the Interface-box has to be performed!
See following chapters for detailed information.
Dip
Function
ON (down)
OFF (up)
1
No function
-
set to OFF
2
CVBS AV1-input
enabled
disabled
3
CVBS AV2-input
enabled
disabled
4
No function
-
set to OFF
5
Rear-view cam type
after-market
factory or none
6
No function
set to OFF
7
No function
set to OFF
8
PDC car
enabled
disabled
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page6
1.4.1.1. Enabling the interface’s video inputs (dip 2-3)
Only the enabled video inputs can be accessed when switching through the interface’s video
sources. It is recommended to enable only the required inputs for the disabled will be
skipped when switching through the video-interfaces inputs.
1.4.1.2. Rear-view camera setting (dip 5)
If set to OFF, the interface switches to factory picture while the reverse gear is engaged to
display factory rear-view camera.
If set to ON, the interface switches to its rear-view camera input „Camera-IN“ while the
reverse gear is engaged.
1.4.1.3. PDC car settings (dip 8)
Dip 8 is for the PDC car representation. If set to ON while the reverse gage is enabled, the
display shows a smaller reverse picture and for that the PDC car representation additionally
appears on its right side. If set to OFF while the reverse gage is enabled, the reverse picture
will be shown in full size.
Note: Dip 1 und 4 are out of function and have to be set to OFF.
2. Installation
To install the interface, first switch off the ignition and disconnect the vehicle’s battery.
Please read the owner`s manual of the car, regarding the battery`s disconnection! If
required, enable the car`s Sleep-mode (hibernation mode)
In case the sleep-mode does not succeed, the disconnection of the battery can be done
with a resistor lead.
If the necessary stabilized power supply for the interface is not taken directly from the
battery, the chosen connection has to be checked for being constantly stabile.
The interface needs a permanent 12V source!
Note: Before a final installation, we recommend a test-run to ensure the compatibility of the
vehicle and the interface. Due to changes in the production of the vehicle manufacturer
there’s always a possibility of incompatibility.
2.1. Place of installation
The interface should be installed on the backside of the head unit.
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page7
2.2. Connection schema
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page8
2.3. Connection - PNP Power / CAN cable
Connect the female 6pin connector of the 6pin to8pin cable to the 6pin connector of the
video interface.
Remove the female Quadlock connector of the vehicle harness from the rear-side of the
head-unit, clip-out chamber connectors A, B and the optical leads (see left picture and next
page) and connect this Quadlock connector to the male Quadlock connector of the PNP
Power / CAN cable.
Clip-in the previously clipped-out chamber connectors in the opposite Connect the opposite
female Quadlock connector of the PNP Power / CAN cable and connect this Quadlock
connector to the previously become free male Quadlock connector at the rear-side of the
head unit.
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page9
2.3.1. Exchange of Quadlock chambers
Version 04.05.2021 CAM(V31)9275&9276(V11) CI-RL2-SC14
Page10
2.4. Analogue connecting - video-interface
If the communication between the CAN box and the vehicle’s CAN bus does not succeed (not
all vehicles are compatible), an analogue connection is required by connecting the 6pin to
8pin cable without the CAN box.
Connect the female 6pin connector of the 6pin to 8pin cable to the 6pin connector
of the video interface.
Connect the yellow, the red and the black wire of the 6pin to 8pin cable to the
vehicle’s power and ground.
Note: The connection of the green wire (Reverse signal) will be described in chapter “After-
market rear-view camera”. The white wire, can be used to switch the enabled video sources,
same as the keypad (see chapter “video interface-operation”). The grey wire stays
unconnected.
Inhaltsverzeichnis
Andere Car-Interface Autozubehör Handbücher
Car-Interface
Car-Interface CI-RL3-MIB-TT-LA Bedienungsanleitung
Car-Interface
Car-Interface CI-RL4-R40-E Bedienungsanleitung
Car-Interface
Car-Interface CI-RL3-LR17 Bedienungsanleitung
Car-Interface
Car-Interface CI-RL4-MZD88 Bedienungsanleitung
Car-Interface
Car-Interface CI-UCON5-JEEP Bedienungsanleitung
Car-Interface
Car-Interface CI-CARPLAY-NTG5 Bedienungsanleitung
Car-Interface
Car-Interface TV-Free CI-TF-PCM21 Bedienungsanleitung
Car-Interface
Car-Interface v.LiNK CI-VL2-PC-HSD Bedienungsanleitung
Car-Interface
Car-Interface r.LiNK CI-RL2-N900 Bedienungsanleitung
Car-Interface
Car-Interface CI-RL2-MZD Bedienungsanleitung
Car-Interface
Car-Interface CI-RL3-LR16-8 Bedienungsanleitung
Car-Interface
Car-Interface TV-Free CI-TF-SC14 Bedienungsanleitung
Car-Interface
Car-Interface CI-RL2-MTC Bedienungsanleitung
Car-Interface
Car-Interface CI-VL2-CCC Bedienungsanleitung
Car-Interface
Car-Interface CI-CARPLAY-NTG45 Bedienungsanleitung
Car-Interface
Car-Interface TV-Free CI-TF-UCON22 Bedienungsanleitung
Car-Interface
Car-Interface CI-RL4-NAC12 Bedienungsanleitung
Car-Interface
Car-Interface CI-RL5-MIB-STD2 Bedienungsanleitung
Car-Interface
Car-Interface RL4-MBN6 Bedienungsanleitung
Car-Interface
Car-Interface CI-UCON5N Bedienungsanleitung
