Cateye RC232CE Bedienungsanleitung

RS232C Communication Kit

Instruction Manual

For Model EC-1500

RS232C Communication Kit 2

Thank you for purchasing the RS232C Communication Kit Ergosiser EC-1500.

By connecting the EC-1500 and an external computer to this kit, the following

control and data transfers are possible using the directional communication

capability of the RS232C interface:

・Controlling and carrying out the EC-1500 internal program from an

external computer.

・Retrieving data (pulse rate, wattage, etc.) of the EC-1500 from an

external computer.

These features expand the application of the EC-1500 functions such as load

and sphygmomanometer. This means that by programming a particular

protocol on a personal computer, data (pulse rate, wattage, etc.) that the EC-

1500 has collected can be handled on a personal computer for further

processing and storage on a disk. Before using this communication kit,

thoroughly read the manual for better performance. Keep this manual and the

warrantee card as long as you use the kit.

[1] Preparation

1-1) Checking components in the package............................................3

1-2) Assembling RS232C communication kit.........................................4

1-2-a) Installing RS board 4 in operation unit.................................4

1-2-b) Connecting optical cable to operation unit..........................4

1-2-c) Connecting procedure ...........................................................5

[2] Learning how the system works

2-1) Data transfer format ..........................................................................6

2-2) Architecture of data transferred from EC-1500 ..............................6

2-2-a) During a program selection and during setting exercise

condition .................................................................................6

2-2-b) During training........................................................................7

2-3) Command used to externally control the EC-1500 ........................8

2-3-a) Exercise condition setting commands .................................8

2-3-b) Command that duplicates push button............................... 8

2-4) Considerations on data transfer ......................................................9

2-4-a) Use of BASIC is convenient to control from external

device ......................................................................................9

2-4-b) Reset first ................................................................................9

2-4-c) Selecting EC-1500 programs .................................................9

2-4-d) Changing exercise conditions ............................................10

2-4-e) Starting EC-1500 program (training)...................................10

2-4-f) Receiving in-training data....................................................10

2-4-g) Changing exercise conditions during training ..................11

2-4-h) Ending training .....................................................................11

2-4-i) Other considerations ...........................................................11

[3] Sample program

3-1) Program that verifies connection to the EC-1500 (CHECK) ........12

3-2) Program that controls the EC-1500 externally (TEST).................13

Introduction to

the system

Table of Contents

3RS232C Communication Kit

KIS-00RC000-P

DCIN

OUTIN

・The package should include the following components. If there is a missing

component, notify the fact to the store where you bought this kit.

1Optical cable

2Converter

3AC adaptor for converter

4RS board

5Connection cable

6Cord clip

7Instruction manual (this book)

8Warrantee card (Note1) / Inquiry slip (Note 2)

Disk write request card (Note 3)

1-1) Checking components in the package

[1] Preparation

Note 1 : Return to the distributor the User Registration Card attached to the

warrantee. Answers to questions written in the inquiry slip and

loading of the sample program onto a disk are valid only once the

registration card has reached us.

Note 2: Inquiry by telephone is not assured to be answered. If you have any

questions, write them down on the inquiry slip and send the slip by

mail or fax to the distributor.

Note 3: If you want to have a disk containing the sample program (TEST) in

this manual, send this card to the distributor. About the fee, ask to

the distributor and pay by registered postal money order.

RS232C Communication Kit 4

RS board

Lower body

of operation unit

Socket

RS board

Circuit board

Plug in

Connector cable

1-2) Assembling RS232C communication kit

1-2-a) Installing RS board 4in

operation unit

・Remove the 8 screws that are holding the upper body on the rear panel of

the operation unit. Open the unit's upper body as shown in the figure

below.

・Referring to the figure, place the RS board so that its mounting holes are

aligned with mounting holes in the unit and the black optical cable

connector is located at the rear end of the unit. Secure the board with the 2

screws supplied.

・Connect the board to the unit via the connector cable supplied.

KIS-00RC000-P

DCIN

OUTIN

Optical cable connector

Converter

AC Adapter connector

To operation unit

1-2-b) Connecting optical cable

to operation unit

・Close the upper body and secure it with the 8 screws.

• Remove the covers from the optical connector and converter. Insert the

optical cable connector and the AC Adapter connector into the converter

socket with the correct orientation. (If the optical cable connector is badly

oriented, it will not plug into the converter.)

5RS232C Communication Kit

PULL OUT PUSH IN

Optical cable connector

of RS board

Cap(A)

Optical cable connector

Optical cable

Plug in

Remove

Cap(B)

Converter RS232C port

AC Adapter Optical cable

OFF

EC-1600

RESET

MODE

ADV

1-2-c) Connecting procedure

•Remove the caps (A) & (B) connect the optical cable connector to the

operation unit optical cable connector. (Fix both caps (A) & (B) when it’s

unused.)

* Secure the optical cable on the handlebar post with the cord clip.

1. Connect the converter to the RS232C port of the computer.

2. Connect the power source to the operation unit, the converter and the

computer.

3. Turn on the system in this order.

Now, the system is ready to operate.

RS232C Communication Kit 6

Age:"40"

Pulse limit value:"160"

Target time:"20"minutes

Weight:"60"lb(or kg)

Setting torque:"1.0"kg•m

Exercise Pattern (Hill Profile Training)

Sex:"1"male

Target Pulse Rate (Auto Training):"120"bpm

Exercise Pattern (Interval Training):"3"

Setting wattage (Isopower Training):"60"watts

Shows during setting conditions

2-2) Contents of Data Transmission from the EC-1500

・Communication speed (baud rate) 2400

・Data bit length 8 bit

・Stop bit 1 bit

・Parity check none

・XON / XOFF control none

・SI/SO control none

[2] Learning how the system works

2-1) Transmission Format

・The EC-1500 outputs display data in character code, continuously when you

set exercise conditions and once per second when you are exercising. Since

the contents of the LCD differs according to setting exercise conditions and

during exercise, the content of data output also differs.

・The EC-1500 sends data to an external computer continuously.

Address Data Function

1 A code Hexadecimal 41H

2 3 digit numeric Setting wattage (Isopower Training)

5 1 digit numeric Exercise Pattern (Interval Training)

6 3 digit numeric Target Pulse Rate (Auto Training)

9 1 digit numeric Sex (male:"1", female:"0")

10 1 digit numeric Exercise Pattern (Hill Profile Training)

11 2 digit numeric Setting torque x 10

13 3 digit numeric Weight (Aerobic power measurement)

16 2 digit numeric Target time (minutes)

18 3 digit numeric Pulse limit value

21 2 digit numeric Age

23 CR code Hexadecimal 0DH

2-2-a) Setting Exercise Conditions

e.g.)

A060312011100602016040CR

7RS232C Communication Kit

Setting wattage (Isopower

Training):"60"watts

Aerobic power measure-

ment result: PWC max.

Aerobic power measure-

ment result: MOU

Aerobic power measure-

ment result: PFL

Pedal cadence:"60"rpm

Pulse rate:"85"bpm

Pedal torque: "0.5"kg•m

Wattage:"31"watts

Calorie consumption:"2"Kcal

Elapsed time:"1"min. "32"sec.

shows during exercise

2) During Exercise

e.g.)

B013200020310508506000000006042CR

・The EC-1500 sends data to an external computer every second.

Address Data Function

1 B code Hexadecimal 42H

2 4 digit numeric Elapsed time Higher 2 digits = "minute"

Lower 2 digits = "second"

6 4 digit numeric Calorie consumption

10 3 digit numeric Wattage

13 2 digit numeric Pedal torque x 10

15 3 digit numeric Pulse rate

18 3 digit numeric Pedal cadence

21 1 digit numeric Aerobic power measurement result: PFL

22 2 digit numeric Aerobic power measurement result: MOU

24 3 digit numeric Aerobic power measurement result: PWC max.

27 3 digit numeric Setting wattage (Isopower Training)

30 2 digit numeric

Lowest 2 digits of addition value of data address 2 ~29

32 CR code Hexadecimal 0DH

Note: "0" is displayed in each digit for the 3 types of aerobic power

measurement results, until the program is completed.

Lowest 2 digits of

addition value of

data address 2 ~29

RS232C Communication Kit 8

・By using the following character codes for button values, you can externally

control the program during exercise.

Example) Sending "i CR" during Manual Training --->

increases pedal resistance (torque: kg.m.) 0.1 kg.m.

Character Code

Function

r RESET button

g ADV button

i + 1 button

d - 1 button

x Stops data output from the EC-1500. Data transmission can

be recovered by either turning on the power, pressing on the

reset button, or applying the "y" signal below. Even during

the interruption of data transmission, the acknowledged

signal "a" + CR is an output.

2-3) Externally Controlling the EC-1500

2-3-a) During Setting Exercise

Conditions

・When exercise conditions are being set you can send data in a "character

code + numeric code + CR code format (shown in example below) from an

external computer, setting your exercise conditions.

Example) "K6CR" : Selects Auto Training

Character Code

Function

A Age (up to 2 digits)

B Pulse limit (up to 3 digits)

C Target time (up to 2 digits)

D Weight (up to 3 digits)

E Setting torque x 10 (2 digits)

F Exercise pattern (Hill Profile Training)

G Sex (male: "1", female: "0")

H Target pulse rate (up to 3 digits)

*I Setting wattage (up to 3 digits)

J Exercise pattern (Interval Training)

K Exercise program

1: Aerobic Power Measurement

2: Manual Training

3: Hill Profile Training

4: Interval Training

5: Isopower Training

6: Auto Training

*L Reset torque during exercise x 10 (2 digits)

Note 1: * marked character code commands are effective even during

exercise. With thes command, you can specify your own protocl.

Note 2: If you want to set weight as 90 lb, you can specify whichever

"D090" or "D90".

2-3-b) During Exercise

9RS232C Communication Kit

y Restart data output from the EC-1500.

b Makes the EC-1500 buzzer beep for 1 second. If the EC-

1500 receives this signal again while the buzzer is still

beeping, another beep will immediately be heard for 1 more

second.

2-4-b)Reset first

2-4-c) Selecting EC-1500 programs

2-4-a) Use of BASIC is convenient

to control from external

device

・Although the EC-1500 can interpret software of any language, its serial

function is basically designed to easily accept BASIC language. For example,

EC-1500 data can be read through the use of the command "INPUT #1, RX$"

or the like, and data can be fed to the EC-1500 through the command "PRINT

#1, TX$" or the like.

・Sending "r CR" duplicates the pressing of the reset button, initializing the EC-

1500. Before externally controlling the EC-1500, first, implement the reset

command. When using BASIC, do as follows:

TX$ = "r"

PRINT #1, TX$

・The computer may send the code "r CR LF". The EC-1500 can respond to

this code. It can also respond to "r LF". All code that the personal computer

sends to the EC-1500 are ciphered correctly.

・In the initial screen, data corresponding to the exercise conditions currently

set are sent in sequence. One set of data consists of a code "A......CR". To

wait for an output, do as follows:

*LOOP INPUT #1,RX$

IF LEFT$(RX$,1)<>"A" GOTO *LOOP

・The next step is to select an EC-1500 training program. For example, to set

to manual training, send "K 2 CR" code. This can easily be done as follows:

TX$ = "K2"

PRINT #1, TX$

・To change the screen to the exercise condition setting, press the button ADV.

Sending "g CR" code has the same effect. For example, enter as follows:

TX$ = "g"

PRINT #1, TX$

2-4) Considerations on data transfer

RS232C Communication Kit 10

・To set the age to 30, send the code "A 30 CR", as shown below.

TX$ = "A30"

PRINT#1,TX$

In the same way, other exercise conditions can be changed.

CAUTION: Some computers will express TX$ as "Asp30" when "AGE=30

: TX$="A" (AGE)" is entered. The EC-1500 recognizes this as an

error code and will not return the acknowledged signal "a".

・The setting range of torque is 0.5-4.0 kg•m. The value is multiplied by 10, i.e.

5-40 kg, and transmitted via RS232C interface. To set the torque to 2.5 kg•m

output a character code "E 25".

・By sending the following BASIC codes, exercise condition display data can

be obtained from EC-1500, and then decoded.

INPUT#1,RX$

AGE = VAL(MID$(RX$,21,2)) ;Age

LTPLS = VAL(MID$(RX$,18,3)) ;Pulse limit value

TGTM = VAL(MID$(RX$,16,2)) ;Target time

WEIGHT = VAL(MID$(RX$,13,3)) ;Weight (Aerobic Power

Measurement)

TGTQ = VAL(MID$(RX$,11,2))/10 ;Set torque

PROF = VAL(MID$(RX$,10,1)) ;Exercise Pattern (Hill Profile Training)

SEX = VAL(MID$(RX$,9,1)) ;Sex Male="1" Female ="2"

TGPLS = VAL(MID$(RX$,6,3)) ;Target pulse rate (Auto Training)

NTVL0 = VAL(MID$(RX$,5,1)) ;Exercise Pattern (Interval Training)

TGWATT = VAL(MID$(RX$,2,3)) ;Set wattage (Isopower Training)

・Pressing the ADV button puts the EC-1500 into exercise status. As with 2-4-

c), sending the "g CR" code duplicates the ADV button, preparing exercise

conditions.

・When the EC-1500 program starts, transmitted data will change to a set of

exercise data consisting of ten elements beginning with the code B. The data

is transmitted every second, even when the printer is working.

・By sending the following BASIC codes, in-training data can be obtained from

EC-1500, and then decoded.

INPUT#1,RX$

TM = VAL(MID$(RX$,2,4))/100 ;Elapsed time ( min. sec.)

KCAL = VAL(MID$(RX$,6,4)) ;Calorie consumption

WATT = VAL(MID$(RX$,10,3)) ;Wattage

TQ = VAL(MID$(RX$,13,2))/10 ;Pedal torque X.X kgm

HR = VAL(MID$(RX$,15,3)) ;Pulse rate

CDC = VAL(MID$(RX$,18,3)) ;Pedal cadence

PFL = VAL(MID$(RX$,21,1)) ;Aerobic power measurement:PFL

MOU = VAL(MID$(RX$,22,1)) ;Aerobic power measurement:MOU

PWC = VAL(MID$(RX$,24,3)) ;Aerobic power measurement:PWCmax

TGWATT= VAL(MID$(RX$,27,3)) ;Setting wattage (Isopower Training)

Note: Measurements on aerobic (PFL, MOU, PWC) are at zero until the

physical strength test is completed.

2-4-d) Changing exercise conditions

2-4-e) Starting EC-1500 program

(training)

2-4-f) Receiving in-training data

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cateye Fitnessgeräte Handbücher

Cateye

Cateye Ergociser EC-5000 Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung