CB2 CROSSROADS Bedienungsanleitung

crossroads BOOKSHELF

hardware

components

tools required

Thank you for purchasing the Crossroads Bookshelf.

This page

lists all the contents included in the box.

Please take the time

to identify the hardware as well as

the individual components

to this product. As you

unpack and prepare for assembly, place the contents

on a carpeted or padded area to protect them from

damage.

Note: 2 people are required to safely assemble this product.

Missing hardware?

Please call 800.606.6387 for

replacements.

1 - bottom panel

1 - top panel

3 - small shelves

2 - large shelves

2 - back panels

(1 left, 1 right)

2 - side panels

Made in Vietnam - r09 Page 1 of 4

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

28 - wood

dowels

8 - bolts

8- flat

washers

8 - spring

washers

mounting hardware

4 - small

screws

4 - large

screws

4 - plastic

anchors

2 - wall

straps

4 - wall

brackets

phillips head screwdriver

2.5mm (1/16”) drill bit

26 - cam

screws

26 - cams 26 - cam

covers

2 3

A. Insert 6 cams into each small shelf as shown. Make sure arrows on each cam point toward the nearest

edge with holes.

B. Insert 8 cam screws into top panel as shown. Secure, but do not over tighten, screws using a phillips

head screwdriver.

C. Insert 4 wood dowels and 2 cams into each large shelf as shown.

small shelf

Make sure arrows on

each cam point toward

nearest edge with holes

large shelf

top panel

NOTE: Do not over

tighten the cam screws

crossroads BOOKSHELF

A. Insert 6 cam screws, 10 wood dowels and 2

cams into each side panel as shown.

B. Insert 3 cam screws into left and right back

panels as shown.

side panel

small shelf

side panel

Fit dowels of side panel into corresponding holes

of small shelves as shown. Turn each cam

clockwise until it securely engages each cam

screw, using a phillips head screwdriver.

Made in Vietnam - r09 Page 2 of 4

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

left and right

back panel

small shelf

Cam in

unlocked

position

Cam in

locked

position

6 7

4 5

crossroads BOOKSHELF

Attach bottom panel to assembled unit as shown

with 8 bolts, 8 spring washers and 8 flat

washers. Secure, but do not over tighten, bolts

using a phillips head screwdriver.

NOTE: Do not over

tighten the bolts

Fit cam screws of left and right back panels into

corresponding holes of assembled unit as shown.

Do not secure cams until further instructions.

Made in Viietnam - r09 Page 3 of 4

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Fit dowels of remaining side panel into

corresponding holes of small shelves as shown.

Secure all cams.

side panel

With the assistance of another adult, position

assembled unit as shown. Fit notches of large

shelves into corresponding notches of assembled

unit as shown.

large

shelf

large

shelf

NOTE: Make sure red

arrows on large

shelves are pointing

the same direction

during assembly

crossroads BOOKSHELF

Made in Vietnam - r09 Page 4 of 4

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

For added safety and stability, it is recommended that the wall mounting hardware be

installed. For safe mounting, it is essential to use wall anchors appropriate to your wall

type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.

A) With a 2.5mm (1/16”) drill bit, drill two holes to the top of unit. Attach 2 wall

brackets with 2 small screws per bracket as shown.

B) Determine the final location of unit. Mark position on the wall, approximately 2"

below the wall bracket mounted to the back of the unit.

C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall

that is slightly smaller in diameter than the anchor. Gently tap each plastic anchor

until the flange of the anchor is flush with the wall.

D) Attach 2 wall brackets to the wall by inserting 2 large screws through the wall

bracket and into the wall anchor in the wall.

E) Place the unit so the wall bracket on the back edge is aligned with the wall bracket.

F) Lace one end of the wall strap through both brackets, and into the other end of the

strap.

G) Pull the strap tightly until secure.

Repeat step A-G for remaining wall mounting assembly.

Wall mounting assembly is now complete.

NOTE: If you are unsure about your wall type or what mounting method you

should use, consult a qualified professional or your local hardware store.

wall mounting assembly

WALL

98 Fit dowels of assembled unit into corresponding

holes of top panel as shown.

With assistance of another adult, position

unit upright, while supporting back panels of

assembly. At this point, secure all cams in top

and back panel. Cover all exposed cams with

cam covers.

Assembly is now complete.

Inhaltsverzeichnis

Andere CB2 Inneneinrichtung Handbücher

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung