CB2 GLOSS Bedienungsanleitung

Made in Vietnam - r05 Page 1 of 4

gloss TALL DRESSER

assembly hardware

components

tools required

Thank you for purchasing the Gloss Tall Dresser.This

page

lists all the contents included in the box. Please

take the time

to identify the hardware as well as the

individual components

to this product. As you unpack

and prepare for assembly, place the contents on a

carpeted or padded area to protect them from damage.

Note: 2 people are required to safely assemble this product.

Missing hardware?

Please call 800.606.6387

for replacements.

(We recommend the use of hand tools instead of power tools)

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

phillips head screwdriver

32 - screws 12 - bolts 12 - wood

dowels

12 - flat

washers

12 - spring

washers

1 - bottom

panel

1 - top

panel

2 - side panels

(1 left, 1 right)

8 - drawer sides

(4 left, 4 right)

4 - drawer

fronts

1 - back

panel

4 - drawer

backs

4 - drawer

bottoms

1 - middle

panel

4 - small

screws

4 - large

screws

2 - wall

straps

4 - mounting

brackets

4 - plastic

anchors

mounting hardware

gloss TALL DRESSER

Made in Vietnam - r05 Page 2 of 4

Insert 4 wood dowels into middle panel as

shown. Fit dowels of middle panel into

corresponding holes of left and right side panels.

Secure each side panel with 2 bolts, 2 spring

washers and 2 flat washers. Secure, but do not

over tighten, bolts with a phillips head

screwdriver.

Insert 4 wood dowels into bottom panel as

shown. Fit dowels of bottom panel into

corresponding holes of side panels, and secure

with 4 bolts, 4 spring washers and 4 flat

washers.

With assistance of another adult, position unit

upright. Fit back panel into corresponding

grooves of side panels as shown.

NOTE: Do not

over tighten bolts

left side

panel

bottom

panel

back panel

NOTE: Make sure grooves

of left and right side panels

are facing each other during

assembly as shown

right side

panel

A. Insert 2 wood dowels into left and right side

panels as shown.

B. Fit dowels of side panels into corresponding

holes of top panel. Secure each side panel with

2 bolts, 2 spring washers and 2 flat washers.

top panel

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

gloss TALL DRESSER

Made in Vietnam - r05 Page 3 of 4

A. Attach left drawer side to drawer front with

2 screws as shown. Secure, but do not over

tighten, screws with a screwdriver.

B. Insert drawer bottom into grooves of drawer

side and front as shown.

Attach right drawer side to drawer front and

back with 4 screws as shown.

Repeat assembly steps 5-7 for remaining 3

drawers.

Attach drawer back to left side drawer with 2

screws as shown.

NOTE: Do not

over tighten

the screws

left drawer

side

drawer

front

drawer

bottom

drawer

back

right drawer

side

Align drawer glides of each drawer with

corresponding drawer glides of assembly as

shown. Firmly push drawer into assembly until

the glides are securely engaged.

Assembly is now complete.

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

NOTE:

Make sure glides are

pulled out of the case, and

ball bearings are at the front of

the extended glides

gloss TALL DRESSER

Made in Vietnam - r05 Page 4 of 4

cleaning & care

Clean surfaces with a dry or damp soft cloth. Do not use

abrasive cleaners. Do not use furniture wax or polish as

the unit is finished with a protective clear lacquer.

NOTE: If you are unsure about your wall type or what mounting method you should use,

consult a qualified professional or your local hardware store.

For added safety and stability, it is recommended that the wall mounting hardware be installed. For

safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall,

concrete, etc.). Mount to wood studs whenever possible.

A) Attach 2 mounting brackets to top of unit using 2 small screws per bracket.

B) Determine the final location of unit. Mark position on the wall, approximately 2" below each

mounting bracket on the back of the unit.

C) Drill a hole in the wall stud. If a wall stud is not available, drill a hole in the wall that is slightly

smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is

flush with the wall.

D) Attach the mounting brackets to the wall by inserting 2 large screws through each mounting

bracket and into the wall anchor in the wall.

E) Position the unit so the mounting brackets on the back of the unit are aligned with the wall

brackets.

F) Lace one end of each wall strap through corresponding brackets, and into the other end of the

strap.

G) Pull the straps tightly until secure.

Wall mounting assembly is now complete.

wall mounting assembly

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Inhaltsverzeichnis

Andere CB2 Inneneinrichtung Handbücher

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung