Chauvet DJ 4BAR Flex T USB Bedienungsanleitung

Quick Reference Guide

QUICK REFERENCE GUIDE

4BAR Flex T USB QRG Rev. 2

About This Guide

The 4BAR Flex T USB Quick Reference Guide (QRG) has basic product information such as mounting, menu options,

and DMX values. Download the User Manual from www.chauvetdj.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to change without notice.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance.

Contact

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your distributor to request support or return a

product. Visit www.chauvetdj.com for contact information.

What is Included

• 4BAR Flex T USB

• Wireless Footswitch

•CarryBag

• Power Cord

• Hanging Brackets with Mounting Hardware

• Warranty Card

• Quick Reference Guide

To Begin

Unpack your 4BAR Flex T USB and make sure you have received all parts in good condition. If the box or contents

appear damaged, notify the carrier immediately, not Chauvet.

• This product is not intended for permanent installation.

• ONLY connect this product to a grounded and protected circuit.

• DISCONNECT from power before cleaning or replacing the fuse.

• DO NOT look at the light source when the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect this product from power by pulling on the cord.

• When mounting this product overhead, ALWAYS use a safety cable.

• DO NOT allow flammable materials close to the product when it is operating.

• DO NOT touch the product’s housing when it is on because it will be hot.

• The voltage of the outlet to which you are connecting this product must be within the range stated

on the decal or rear panel of the product.

• This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose this

product to rain or moisture.

• In the event of a serious operating problem, stop using immediately.

• Always mount this product in a location with adequate ventilation, at least 20 in (50 cm) from

adjacent surfaces.

• Be sure that no ventilation slots on the unit’s housing are blocked.

• Never connect this product to a dimmer or rheostat.

• Replace the fuse with the same type and rating.

• Never carry the product by the power cord. Use only the handle to carry this product.

• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher

temperatures.

• DO NOT open this product. It contains no user-serviceable parts.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely

disconnect the product from power via breaker or by unplugging it.

4BAR Flex T USB QRG Rev. 2

QUICK REFERENCE GUIDE

Product Description

The 4BAR Flex T USB is a complete wash-lighting solution, featuring the classic 4BAR style of 4 fully adjustable heads,

ﬁtted with high-intensity tri-color (RGB) LEDs that can be controlled wirelessly via the included footswitch or the optional

IRC-6 controller (sold separately). It also features D-Fi USB compatibility for wireless master/slave or DMX control. For

added flexibility, a pass-through hole easily mounts the fixture to most tripods or speaker stands without the need for

additional clamps. Two floor stands (L-brackets) are included to maximize setup possibilities and configurations. It also

features two additional power outlets and mounting options for additional wash or effect lights. Aconvenient carrying bag

is included for quick and easy setup and tear-down.

Overview

Footswitch Overview

AC Power

This product has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz.

To eliminate wear and improve its lifespan, during periods of non-use completely disconnect the

product from power via breaker or by unplugging it.

Adjustable

Pass- Through

for Tripod

mounting

Power In

Fuse

Holder

LED Display

Adjustment

Knob Power Out

DMX In/Out

D-Fi USB

Port

Buttons

Power Out

Adjustment

Knob

DIP

Switch Power

Switch

9-Volt Battery

Cover

QUICK REFERENCE GUIDE

4BAR Flex T USB QRG Rev. 2

Power Linking

For the maximum number of 4BAR Flex T USB products that you can power link at each voltage, see the User Manual or

the sticker on the product.

Fuse Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the safety cap out of the housing.

4. Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the exact same

type and rating.

5. Re-insert the fuse holder and reconnect power.

Mounting

Before mounting this product, read the Safety Notes. This product can be mounted to most tripods, trussing (using

appropriate clamps and with/without the included mounting brackets) or can be used floor/surface mounted.

Mounting Diagram

Control Panel Description

BUTTON FUNCTION

<MENU> Exits from the current menu or function

<UP> Navigates upwards through the menu list and increases the numeric value when in a function

<DOWN> Navigates downwards through the menu list and decreases the numeric value when in a function

<ENTER> Enables the currently displayed menu or sets the currently selected value into the selected

function

Mounting Clamp

(such as CLP-15 from Chauvet)

Mounting Bracket

Bracket

Adjustment Knob

Tripod (sold separately)

Insertion Point w/

Adjustment Knob for

Tightening IR Sensor for use with

IRC-6

(DO NOT block)

4BAR Flex T USB QRG Rev. 2

QUICK REFERENCE GUIDE

Menu Map

DMX Linking

The 4BAR Flex T USB can work with a DMX controller. Instructions for connecting and configuring this product for DMX

operation are in the User Manual. If you are not familiar with DMX, download the DMX Primer from www.chauvetdj.com.

Starting Address

To ensure full access to all channels available in each DMX mode, the highest recommended DMX address is 510.

Master/Slave Connection

The 4BAR Flex TUSB uses the DMX data connection for its Master/Slave mode. Information about configuring the 4BAR

Flex T USB for Master/Slave operation is in the User Manual, which is available from the Chauvet website.

IRC-6 (Infrared Remote Control)

The 4BAR Flex T USB can be operated with the CHAUVET DJ IRC-6. For more information about the IRC-6, download

instructions for the IRC-6 or the 4BAR Flex T USB User Manual from www.chauvetdj.com.

Wireless FootSwitch Operation The included wireless footswitch provides quick access to preset

colors, color-change programs, andsound-activation through the

4BAR Tri USB microphone.

To use the footswitch:

1.Connect the 4BAR Flex T USB to power. Turn the wireless

footswitch on.

2.Press <MENU> on the 4BAR Flex T USB and navigate to rF

mode and press <ENTER>. Choose a channel and press

<ENTER>.

3.Press <MENU> on the 4BAR Flex T USB and navigate to

Auto mode and press <ENTER>.

4.Set the DIP switch channel on the wireless footswitch to match

the channel set on the 4BAR Flex T USB. (Use the DIP Switch

Channels image for help)

5.Press pedal #1 (Colors) to activate Static Color controls. When

working, all the lights will begin in a Static color and FOOr will

appear on the Menu display.

6. Use the chart below to activate the desired function.

MODE PROGRAMMING LEVELS DESCRIPTION

DMX Mode 3Ch d001–510 3-channel DMX mode

15Ch d001–498 15-channel DMX mode

Static Colors C-- C 1–7 Static colors

Automatic

Programs Auto Automatic programs

Auto Speed S-- S 1–100 Program speed for P 1–7

Sound-Active Mode Snd Sound-active programs

Sound Sensitivity Sens u 1–100 Sound sensitivity

Custom Color

Mixing U-- r000–255 Custom static colors

Combine red, green and blue

g000–255

b000–255

Infrared Mode SEt on Turns infrared on or off

oFF

Wireless

Footswitch rF On rF 1 – rF16 Turn on/off wireless footswitch connectivity and

selects receiving channel (receiving channel

must match transmitting channel on the

footswitch)

Off

QUICK REFERENCE GUIDE

4BAR Flex T USB QRG Rev. 2

PEDAL ACTION FUNCTION

(Static Colors) Tap Pedal to activate, then Tap to

navigate to desired function

White

Red

Green

Blue

Yellow

Magenta

Cyan

Auto Mode (snap)

Auto Mode (fade)

(Sound/Strobe Mode)

Tap Pedal Enter Sound Mode

Hold Pedal Down Strobe Mode

Tap Pedal Again Turn off Strobe (Sound Mode only)

(Blackout)

Tap Pedal Black out Fixture

Hold Pedal Down Fade to Blackout

Tap Pedal Again/Hold PedalAgain Turn off Blackout/Fade from Blackout

The 4BAR Tri USB footswitch will work properly in any mode, with a maximum

unobstructed distance of 50 ft (15.24 m). You must turn on the rF on the 4BAR Tri

USB, set the rF channel, and navigate to Auto mode before using the footswitch.

4BAR Flex T USB QRG Rev. 2

QUICK REFERENCE GUIDE

DIP Switch Channels

D-FI USB Connectivity

The 4BAR Flex T USB is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from

CHAUVET DJ. Simply set the DIP switch D-Fi receiving/transmitting channel, plug it into the USB port then set the

product's DMX Personality and DMX Address. Further instructions for connecting and configuring this product for D-Fi

USB operation are in the 4BAR Flex T USB User Manual or D-Fi USB Instruction Sheet.

For Illustrative purposes only.

WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may

cause damage to the product.

Channel 1

Channel 2

Channel 3

Channel 4

Channel 5

Channel 6

Channel 7

Channel 8

Channel 9

Channel 10

Channel 11

Channel 12

Channel 13

Channel 14

Channel 15

Channel 16

1234

QUICK REFERENCE GUIDE

4BAR Flex T USB QRG Rev. 2

DMX Values

15Ch

4BAR Flex T USB Zones for DMX Control (15Ch)

3Ch

CHANNEL FUNCTION VALUE PERCENT/SETTING

1 Auto Programs

000 009 No Function

010 029 Auto Program 1

030 049 Auto Program 2

050 069 Auto Program 3

070 089 Auto Program 4

090 109 Auto Program 5

110 129 Auto Program 6

130 149 Auto Program 7

150 169 Auto Program 8

170 189 Auto Program 9

190 209 Auto Program 10

210 229 Auto Program 11

230 249 Auto Program 12

250 255 Sound Mode

2 Dimmer 000 255 0–100%

3Strobe /Auto Program

Speed / Sound

Sensitivity

000 009 No function

010 255 Strobe, slow to fast

000 255 Auto Program speed, slow to fast

000 010 Sound Sensitivity OFF

011 255 Sound-Active Sensitivity, low to high

4Red1 000 255 0–100%

5Green1 000 255 0–100%

6Blue1 000 255 0–100%

7Red2 000 255 0–100%

8Green2 000 255 0–100%

9Blue2 000 255 0–100%

10 Red 3 000 255 0–100%

11 Green 3 000 255 0–100%

12 Blue 3 000 255 0–100%

13 Red 4 000 255 0–100%

14 Green 4 000 255 0–100%

15 Blue 4 000 255 0–100%

CHANNEL FUNCTION VALUE PERCENT/SETTING

1RedAll 000 255 0–100%

2GreenAll 000 255 0–100%

3BlueAll 000 255 0–100%

4BAR Flex T USB GRR Rev. 2

GUÍA DE REFERENCIA RÁPIDA

Acerca de esta guía

La Guía de referencia rápida (GRR) del 4BAR Flex T USB contiene información básica sobre el producto, como montaje,

opciones de menú y valores DMX. Descargue el manual de usuario de www.chauvetdj.com para una información más

detallada.

Exención de responsabilidad

La información y especificaciones contenidas en esta GRR están sujetas a cambio sin previo aviso.

Notas de seguridad

Estas notas de seguridad incluyen información importante sobre el montaje, uso y mantenimiento.

Contacto

Fuera de EE. UU., Reino Unido, Irlanda, México o Benelux póngase en contacto con su distribuidor para solicitar

asistencia o devolver un producto. Visite www.chauvetdj.com para información de contacto.

Qué va incluido

•4BARFlexTUSB

• Pedal inalámbrico

• Bolsa de transporte

• Cable de alimentación

• Soporte para colgar con material de montaje

• Tarjeta de garantía

• Guía de referencia rápida

Para empezar

Desembale su 4BAR Flex T USB y asegúrese de que ha recibido todas las partes en buen estado. Si la caja o los

componentes parecen dañados, comuníqueselo inmediatamente al transportista, no a Chauvet.

• Este producto no está concebido para una instalación permanente.

• Conecte este producto SOLO a un circuito con toma de tierra y protegido.

• Desconecte siempre de la alimentación antes de la limpieza o sustitución del fusible.

• NO mire a la fuente de luz cuando el producto esté encendido.

• Asegúrese de que el cable de alimentación no está retorcido ni estropeado.

• Nunca desconecte este producto de la alimentación tirando del cable.

• Cuando monte este producto en alto, use un cable de seguridad.

• NO permita la presencia de materiales inflamables cerca de la unidad cuando esté en

funcionamiento.

• NO toque este producto cuando esté en funcionamiento, pues podría estar caliente.

• La tensión del enchufe al que conecte este producto ha de estar en el rango establecido en el

grabado o en el panel posterior del producto.

• ¡Este producto es para uso en interiores solamente! (IP20) Para evitar riesgos de incendio o

descarga, no exponga este producto a la lluvia o la humedad.

• Monte siempre este producto en una ubicación con ventilación adecuada, al menos a 20 in (50

cm) de superficies adyacentes.

• Asegúrese de que ninguna ranura de ventilación en la carcasa de la unidad queda bloqueada.

• Nunca conecte este producto a un atenuador o reostato.

• Sustituya el fusible con uno del mismo tipo y categoría.

• Use SOLAMENTE los soportes de colgar/montar o las asas para mover este producto.

• La temperatura ambiente máxima es de 104 °F (40 °C). No haga funcionar este producto a

temperaturas más altas.

• En caso de un problema grave de funcionamiento, deje de usarlo inmediatamente.

• NO abra este producto. No contiene piezas reparables por el usuario.

• Para evitar un desgaste innecesario y alargar su vida útil, desconecte completamente el producto

mediante el interruptor o desenchufándolo durante periodos en que no se use.

GUÍA DE REFERENCIA RÁPIDA

4BAR Flex T USB GRR Rev. 2

Descripción del producto

El 4BAR Flex T USB es una solución completa de baño de luz, que incorpora 4 cabezas móviles totalmente ajustables

con el clásico estilo 4BAR, equipadas con LED tricolor (RGB) de alta intensidad que se pueden controlar sin cables a

través del pedal incluido o del controlador IRC-6 opcional (vendido por separado). También es compatible con D-Fi USB

para control maestro/esclavo sin cables o DMX. Y para que sea todavía más flexible, un agujero de paso sirve para

montar fácilmente el dispositivo en la mayoría de trípodes o pies de altavoz sin necesidad de abrazaderas adicionales.

Dos pies de suelo (soportes en L) van incluidos para maximizar las posibilidades de instalación y configuraciones.

También integra dos enchufes de alimentación adicionales y opciones de montaje para añadir baño de luz o efectos. Va

incluida una práctica bolsa de transporte para instalar y desmontar rápidamente.

Visión general del producto

Vista general del pedal

Entrada de

alimentación

Porta-

fusibles

Pantalla

LED

Puerto D-

Fi USB

Salida de

alimentación

Entrada/Salida

DMX

Mando de

sensibilidad

Paso ajustable

para montaje de

trípode

Botones

de menú

Mando de

ajuste

Salida de

alimentación

Tapa pila 9-V

Commutador

DIP Interruptor

encendido

Andere Handbücher für 4BAR Flex T USB

Inhaltsverzeichnis

Sprachen:

Andere Chauvet DJ DJ-Equipment Handbücher

Chauvet DJ

Chauvet DJ Hurricane Bubble Haze Bedienungsanleitung

Chauvet DJ

Chauvet DJ LED Shadow Bedienungsanleitung

Chauvet DJ

Chauvet DJ GigBAR IRC Bedienungsanleitung

Chauvet DJ

Chauvet DJ Hurricane Bubble Haze LT Bedienungsanleitung

Chauvet DJ

Chauvet DJ GigBAR MOVE ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ Hurricane 1302 Bedienungsanleitung

Chauvet DJ

Chauvet DJ FREEDOM CHARGE 8 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SHOCKER PANEL 180 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Stick Pack Bedienungsanleitung

Chauvet DJ

Chauvet DJ Bubble Machine Bedienungsanleitung

Chauvet DJ

Chauvet DJ COREpar Q120 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ Scorpion Dual V2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Wash Zoom 450 IRC Bedienungsanleitung

Chauvet DJ

Chauvet DJ Maverick MK2 Wash Bedienungsanleitung

Chauvet DJ

Chauvet DJ Hurricane 1600 Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4BAR Flex T USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZWedge Tri Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Wash Zoom 450 IRC Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Q1N Bedienungsanleitung

Chauvet DJ

Chauvet DJ Beamer 8 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Geyser P6 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimPAR H6 USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ Vivid Drive 28N Bedienungsanleitung

Chauvet DJ

Chauvet DJ Cumulus HP Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung