Chauvet DJ Geyser P6 Bedienungsanleitung

User Manual

Page 2 of 18 Geyser P6. User Manual Rev. 3

TABLE OF CONTENTS

1. Before You Begin.......................................................................................................... 3

What is Included...............................................................................................................................3

Unpacking Instructions.....................................................................................................................3

Claims ....................................................................................................................................................... 3

Text Conventions .............................................................................................................................3

Symbols............................................................................................................................................3

Disclaimer.........................................................................................................................................3

Product at a Glance..........................................................................................................................3

Safety Notes.....................................................................................................................................4

2. Introduction................................................................................................................... 5

Overview...........................................................................................................................................5

Dimensions.......................................................................................................................................6

3. Setup.............................................................................................................................. 7

AC Power .........................................................................................................................................7

Fuse Replacement .................................................................................................................................... 7

Mounting...........................................................................................................................................8

Orientation................................................................................................................................................. 8

Rigging...................................................................................................................................................... 8

Omega Bracket Placement Options .......................................................................................................... 8

Tank Inversion Steps for Inverted Mounting ..................................................................................10

4. Operation......................................................................................................................11

Control Panel Operation.................................................................................................................11

Menu Map.......................................................................................................................................11

DMX Personality and Starting Address ................................................................................................... 11

DMX Linking...................................................................................................................................11

Configuration (DMX)................................................................................................................................ 11

Configuration (Standalone) ............................................................................................................13

Programmable Color Selection (Wireless Remote Control)..................................................................... 13

Wireless Remote Control......................................................................................................................... 13

5. Technical Information..................................................................................................14

Fogger Maintenance ......................................................................................................................14

Storage/ Maintenance ....................................................................................................................14

General Troubleshooting................................................................................................................15

6. Technical Specifications..............................................................................................16

Returns...........................................................................................................................................17

Contact Us .........................................................................................................................18

Geyser P6 User Manual Rev. 3 Page 3 of 18

1.BEFORE YOU BEGIN

What is

Included

•Geyser P6

•Geyser Wireless Remote Control

•Geyser Wired Remote Receiver

•Omega Mounting Brackets x 2

•Power Cord

•Warranty Card

•Quick Reference Guide

Unpacking

Instructions

Carefully unpack the product immediately and check the container to make sure all the

parts are in the package and are in good condition.

Claims

If the box or the contents (the product and included accessories) appear damaged from

shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet

Failure to report damage to the carrier immediately may invalidate your claim. In

addition, keep the box and contents for inspection.

For other issues, such as missing components or parts, damage not related to shipping,

or concealed damage; file a claim with within 7 days of delivery.

Text

Conventions

Convention

Meaning

1–512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified

Menu > Settings

A sequence of menu options to be followed

<ENTER>

A key to be pressed on the product’s control panel

A value to be entered or selected

Symbols

Symbol Meaning

Critical installation, configuration, or operation information. Not

following these instructions may make the product not work, cause

damage to the product, or cause harm to the operator.

Important installation or configuration information. The product

may not function correctly if this information is not used.

Useful information.

Disclaimer

The works of authorship contained in this manual, including, but not limited to, all design, text and images

are owned by Chauvet.

Electronically published by Chauvet in the United States of America.

CHAUVET, the Chauvet logo, Geyser P6 and Geyser are registered trademarks or trademarks of Chauvet &

Son, LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company

and product names and logos referred to herein may be trademarks of their respective companies.

Product at a

Glance

Use on Dimmer

Auto Programs

Outdoor Use

Fixed voltage (120 V or 230 V)

Sound-Activated

Replaceable Fuse

DMX

User-Serviceable

Master/Slave

Page 4 of 18 Geyser P6. User Manual Rev. 3

Safety Notes

These notes include important information about the mounting,

usage, and maintenance

of this product; read before using the product.

•Always connect the product to a grounded circuit to avoid the risk of electrocution.

•Always disconnect the product from the power source before cleaning or replacing

the fuse.

•Avoid direct eye exposure to the light source while the product is on.

•Make sure the power cord is not crimped or damaged.

•Never disconnect the product from power by pulling or tugging on the cord.

•If mounting the product overhead, always secure to a fastening device using a

safety cable.

•Make sure there are no flammable materials close to the product when operating.

•Do not touch the product’s housing when operating because it may be very hot.

•Do not mount the product on a flammable surface (linoleum, carpet, wood, paper,

carton, plastic, etc.).

•The product’s nozzle is very hot during operation and it remains hot for a long time

after operation has stopped.

•The fog exits the nozzle at a very high temperature. Keep a minimum distance of

6.5 ft (2 m) from the nozzle to the nearest object.

•Do not use the product as a space heater.

•Do not drink or become in contact with the fog fluid. If you do, call your local

emergency service (911 in the US) for help.

•

Do not add perfume, alcohol, gasoline, or any other flammables to the fog fluid.

•Always make sure that the voltage of the outlet to which you are connecting the

product is within the range stated on the decal or panel of the product.

•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not

expose the product to rain or moisture.

•Always install the product in a location with adequate ventilation, at least

20 in (50 cm) from adjacent surfaces.

•Be sure that no ventilation slots on the product’s housing are blocked.

•Make sure there is adequate fog fluid in the machine to prevent pump and heater

damage.

•Never connect the product to a dimmer.

•Make sure to replace the fuse with another of the same type and rating.

•Never carry the product by the power cord or any moving part. Always use the

handles.

•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the

product at higher temperatures.

•In the event of a serious operating problem, stop using the product immediately.

•Never try to repair the product. Repairs carried out by unskilled people can lead to

damage or malfunction. Contact the nearest authorized technical assistance center.

•This product is not intended for permanent installation.

•Use only CHAUVET water-based fog fluid.

•Drain the tank before transporting the product.

•To eliminate unnecessary wear and improve its lifespan, during periods of non-use

completely disconnect the product from power via breaker or by unplugging it.

Keep this User Manual for future use. If you sell the product to another user, be sure

give this document to the next owner.

Fog Cleaner Quart (FCQ) was specifically developed by Chauvet to clean your

Geyser

P6 Make sure you use FCQ regularly, waiting

no longer than 90 days between

cleanings, to increase the life of your fogger.

The Geyser P6 was specifically designed for use with CHAUVET

Quick Dissipating Fluid

(QDF). For optimum performance with your fogger, Chauvet recommends using QDF.

Geyser P6 User Manual Rev. 3 Page 5 of 18

2.INTRODUCTION

Overview

LED Display

Control

Buttons

Nozzle and LEDs

Fluid Tank

On/Off Switch

Removable

Shield

Remote Control

Receiver Port

Fuse Holder

Power In

DMX In/Out

Handles

Page 6 of 18 Geyser P6. User Manual Rev. 3

Dimensions

6.9 in

(175 mm)

12.2 in

(310 mm)

17.4 in

(442 mm)

Geyser P6 User Manual Rev. 3 Page 7 of 18

3.SETUP

AC Power

The Geyser P6

has a fixed voltage power supply and it can work with an input voltage of

either 120 VAC, 60 Hz or 230 VAC, 50 Hz, depending on the specific model.

To determine the product’s power requirements (

circuit breaker, power outlet, and

wiring), use the current value listed on the label affixed to the product

’s panel, or refer to

the product’s specifications chart. The listed current rating indicates the product’s

average current draw under normal conditions.

Always connect the product to a protected circuit

(circuit breaker or fuse). Make

sure the product has an appropriate electrical grou

nd to avoid the risk of

electrocution or fire.

Never connect the product

to a rheostat (variable resistor) or dimmer circuit, even

if the rheostat or dimmer channel serves only as a 0–100% switch.

Fuse

Replacement

Disconnect the product from power before replacing the fuse.

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the fuse holder out of the housing.

4. Remove the blown fuse from the holder.

5. Replace with a fuse of the exact same type and rating.

6. Insert the fuse holder back in place and reconnect power.

A spare fuse is not included; however, the safety cap has room for a spare.

Always replace a blown fuse with another of the same type and rating.

Installed fuse

(held by plastic clip)

Spare fuse holder

(inside safety cap)

Safety cap

Page 8 of 18 Geyser P6. User Manual Rev. 3

Mounting

Before mounting the product

, read and follow the safety recommendations indicated in

the Safety Notes.

Orientation

Primarily, the Geyser P6 is to be floor mounted in a vertical fog jet orientation.

Alternatively, it may also be mounted in a floor mounting/horizontal fog jet orientation or

in an overhead mounting/downward fog jet orientation; however, be sure to follow

instructions closely to avoid tank spills with alternate mountings.

Rigging

•Before deciding on a location, always make sure there is easy access to the product

for maintenance and fluid replenishment.

•Make sure that the structure or surface onto which you are mounting the product

can support the product’s weight (see the Technical Specifications).

•When mounting the product overhead, always use a safety cable. Mount the

product securely to a rigging point, such as an elevated platform or a truss.

•When rigging the product onto a truss, use the omega brackets provided and

mounting clamps of appropriate weight capacity (sold separately). The mounting

holes (size M12) on the bottom of the product are appropriate for this purpose.

•The rubber feet also serve as floor supports. When mounting the product on the

floor, make sure that the product and cables are away from people and vehicles.

Omega Bracket

Placement

Options

Fluid Tank

Orientation

To avoid spillage with any mounting, always position the fluid tank with the tank’s

cap in the uppermost position above the tank’s fluid line.

When mounting the Geyser P6 in any inverted position, remove the fluid tank from

the holder and set it upright on an adjacent surface.

Vertical Fog Jet Horizontal Fog Jet

Fluid Line

A B

Geyser P6 User Manual Rev. 3 Page 9 of 18

Mounting Diagram

Mounting to Truss

With inverted mounting, avoid spillage of the fog fluid by setting the fluid tank in

an upright position. Be sure to use a safety cable for

both the Geyser P6 and the

fluid tank when rigging in this manner. Follow the instructions provided to reverse

fluid tank compartment.

Floor Mounting – Vertical Fog Output

Vertical Mounting – Horizontal Fog Output

Overhead Mounting – Downward Fog Output

*Utilize option A or B

*Utilize option C

Using the Omega Bracket

Placement Options section

as a reference, choose the

best mounting method to

achieve the fog output you

desire.

Safety Cable for the

Fluid Tank

Mounting Clamps for

the Geyser P6

TRUSST®

(or other elevated

platform or truss)

The Fluid Tank in

an upright position

Overhead Mounting – Downward Fog Output

Reversible Fluid

Tank compartment

Safety Cable goes

through pass-thru

Page 10 of 18 Geyser P6. User Manual Rev. 3

Tank Inversion Steps for Inverted Mounting

1. Empty the fluid from the product.

2. Remove the screws and the bottle lock to take out the tank.

3. Turn the fog machine upside down, remove the screws and set aside to take off the

removable plate.

4. Attach the removable plate to the opposite side and secure the tank with the bottle

lock.

5. Secure both the bottom plate and tank cover with the screws.

*Actual product may vary slightly from drawing

Bottle Lock

Removable

Plate

Inhaltsverzeichnis

Andere Chauvet DJ DJ-Equipment Handbücher

Chauvet DJ

Chauvet DJ SlimPAR PRO W USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4Play 2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimPAR T12BT Bedienungsanleitung

Chauvet DJ

Chauvet DJ LED SHADOW 2 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ INTIMIDATOR SPOT 455Z IRC Bedienungsanleitung

Chauvet DJ

Chauvet DJ Cumulus Bedienungsanleitung

Chauvet DJ

Chauvet DJ EVE E-100Z Bedienungsanleitung

Chauvet DJ

Chauvet DJ MotionOrb Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Par H9 IP Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimBANK H18 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Spot 160 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZ Link Par Q6 BT Bedienungsanleitung

Chauvet DJ

Chauvet DJ Pinspot Bar Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimPAR Q6 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ Scorpion Dual V2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ DMX-4 Bedienungsanleitung

Chauvet DJ

Chauvet DJ HURRICANE HAZE 4D Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimPAR PRO H USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ GOBO ZOO 2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SM-250 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Kinta HP Bedienungsanleitung

Chauvet DJ

Chauvet DJ SlimPAR 64 Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZLink Par Q1BT Bedienungsanleitung

Chauvet DJ

Chauvet DJ SHOCKER PANEL 180 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung