Checkpoint Smart-1 5050 Bedienungsanleitung
Classification [Protected]
©2019 Check Point Software Technologies Ltd. All rights reserved.
For a list of our trademarks, please refer to: www.checkpoint.com/copyright.html.
For a list of our Third Party Copyright notices, please refer to: www.checkpoint.com/3rd_party_copyright.html
Smart-1 Installing and Removing
the SAN Card
Classification:[Protected]P/N TBD
Protected
This document is for appliance models Smart-1 5050 and Smart-1 5150.
Safety Instructions
•Lift the appliance with assistance. To avoid injury, do not attempt to lift the
appliance by yourself.
•Opening or removing the appliance cover, while the appliance is powered on
may expose you to a risk of electric shock.
•Do not operate the appliance without the cover for more than five minutes.
Operating the appliance without the cover can result in component damage.
•Many repairs may only be done by a certified service technician. Only
perform troubleshooting and simple repairs as authorized in your product
documentation, or as directed by the technical support.
•We recommend that you always use an antistatic mat and antistatic strap on
your wrist, while working on components inside the appliance.
•To ensure proper operation and cooling, all bays in the appliance and
cooling fans must be always populated with a component or a blank.
For more information, see the
Enterprise Products Safety, Environmental, and
Regulatory Information
booklet supplied in the original appliance shipping
carton.
2
Important - We recommend that only experienced personnel
install or remove hardware components. Installing or
removing components incorrectly can permanently damage
the Security Appliance.
Important - Make sure that you are electromagnetically
grounded when working with hardware components of the
appliance. ESD (electrostatic discharge) can damage the
appliance.
Hardware Components
Smart-1 5050
Item Description
1 Front panel
2 Riser 1
3 Riser 2
4 Rear panel
3
Smart-1 5150
Item Description
1 Front panel
2 Riser 1
3 Rear panel
Procedure
Use the relevant install or replace workflow for your appliance. For each step in
the workflow, follow the instructions as described in the subsequent sections of
this guide.
To install a new expansion SAN card on Smart-1 5050 appliances:
1. Prepare the appliance with a shut down, halt and disconnection of power.
2. Remove the riser.
3. Replace the long bracket on the SAN card with a smaller bracket.
See
Replacing the Bracket on a SAN Card
at the end of the guide.
4. Install a new expansion SAN card into the riser.
5. Install the riser.
4
6. Reassemble the appliance.
7. Install a transceiver.
To install a new expansion SAN card on Smart-1 5150 appliances:
1. Prepare the appliance with a shut down, halt and disconnection of power.
2. Install a new expansion SAN card into the riser.
We recommend that you populate the bottom-most slot first.
3. Reassemble the appliance.
4. Install a transceiver.
To replace an existing expansion SAN card on Smart-1 5050
appliances:
1. Prepare the appliance with a shut down, halt and disconnection of power.
2. Remove the riser.
3. Remove the existing expansion SAN card from the riser.
4. Replace the long bracket on the new SAN card with a smaller bracket.
See
Replacing the Bracket on a SAN Card
at the end of the guide.
5. Install a new expansion SAN card into the riser.
6. Install the riser.
7. Reassemble the appliance.
8. Install a transceiver.
To replace an existing expansion SAN card on Smart-1 5150
appliances:
1. Prepare the appliance with a shut down, halt and disconnection of power.
2. Remove the existing expansion SAN card from the riser.
3. Install a new expansion SAN card into the riser.
4. Reassemble the appliance.
5. Install a transceiver.
5
Preparing the Appliance
To prepare the appliance:
1. Make sure to follow the safety instructions.
2. Shut down the appliance:
•In Gaia Portal:
Go to Maintenance > Shut Down, and click Halt
•In Gaia Clish:
Run: halt
3. Open the retention strap that secures the power cables to the PSUs.
This example shows AC PSUs:
4. If AC PSUs are installed in the appliance:
Disconnect the power cables from the AC PSUs.
5. If DC PSUs are installed in the appliance:
Disconnect the safety ground wires from the DC PSUs.
Disconnect the DC power connectors from the DC PSUs.
6. Remove the hook-and-loop straps that hold and secure the system cables,
if they interfere with the PSU removal.
7. Remove any other attached cables, if necessary.
8. Remove the appliance from the rack.
See the relevant
Installing the Telescoping Rails
booklets for illustrated
installation procedures:
Smart-1 525 and Smart-1 5050 Telescoping Rails
http://supportcontent.checkpoint.com/documentation_download?ID=58649
6
Smart-1 5150 Telescoping Rails
http://supportcontent.checkpoint.com/documentation_download?ID=58650
9. Put the Electrostatic Discharge (ESD) grounding strap on your wrist and
attach the other end to a grounding point.
10. Remove the appliance cover:
a) Use a flat or a Phillips head screwdriver to rotate the latch release lock
counter-clockwise to the unlocked position.
b) Lift the latch.
c) Slide the cover back.
The tabs on the cover should disengage from the guide slots on the
appliance.
d) Hold the cover on both sides and lift the cover away from the appliance.
Removing the Riser
Smart-1 5050
Hold the touch points and lift the riser, from the riser connector, on the system
board.
Removing expansion riser 1:
7
Removing expansion riser 2:
Smart-1 5150
Press the release latches, and lift the riser from the riser connector on the
system board.
8
Installing an Expansion SAN Card into the Riser
Smart-1 5050 and Smart-1 5150
1. Unpack the expansion SAN card and prepare it for installation.
Note -If the appliance is a Smart-1 5050, see
Replacing the Bracket on a
SAN card
at the end of the guide.
2. If applicable, lift/pull the expansion SAN card latch and remove the filler
bracket.
3. Hold the card by its edges, and align the card edge connector with the
expansion SAN card connector on the riser.
4. Insert the card edge connector firmly into the expansion SAN card
connector until the card is fully seated.
5. Close/push the expansion SAN card latch.
Installing an expansion SAN card into the expansion riser 1 on Smart-1 5050:
9
Installing an expansion SAN card into the expansion riser 2 on Smart-1 5050:
Installing an expansion SAN card into the expansion riser 1 on Smart-1 5150:
We recommend that you populate the bottom-most slot first.
10
Removing an Expansion SAN Card from the Riser
Smart-1 5050 and Smart-1 5150
1. If applicable, lift the expansion SAN card latch(es) out of the slot.
2. Hold the expansion SAN card by its edges, and pull the card until the card
edge connector disengages from the expansion SAN card connector on the
riser.
Note -If you do not immediately install a replacement expansion SAN card
when a SAN card fails, leave the failed SAN card in place to ensure proper
appliance cooling until the new SAN card is installed.
Removing an expansion SAN card from the expansion riser 1 on Smart-1 5050:
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Checkpoint Netzwerk-Hardware Handbücher
Checkpoint
Checkpoint QUANTUM SMART-1 6000-L/6000-XL Bedienungsanleitung
Checkpoint
Checkpoint 6000 Series Bedienungsanleitung
Checkpoint
Checkpoint MHO170 Bedienungsanleitung
Checkpoint
Checkpoint 21000 Appliances G-70 Leitfaden
Checkpoint
Checkpoint 16000 Bedienungsanleitung
Checkpoint
Checkpoint 6000 Series Bedienungsanleitung
Checkpoint
Checkpoint QUANTUM MAESTRO Bedienungsanleitung
Checkpoint
Checkpoint 1500 Series Bedienungsanleitung
Checkpoint
Checkpoint 1570 Bedienungsanleitung
Checkpoint
Checkpoint VPN-1 Edge X Series Bedienungsanleitung
Checkpoint
Checkpoint QUANTUM FORCE 19000 Bedienungsanleitung
Checkpoint
Checkpoint QUANTUM SPARK 1500 Bedienungsanleitung
Checkpoint
Checkpoint TE250X Bedienungsanleitung
Checkpoint
Checkpoint QUANTUM SPARK 1530 Bedienungsanleitung
Checkpoint
Checkpoint 1500 Series Bedienungsanleitung
Checkpoint
Checkpoint 5000 Series Bedienungsanleitung
Checkpoint
Checkpoint IPS-1 Bedienungsanleitung
Checkpoint
Checkpoint 4200 Bedienungsanleitung
Checkpoint
Checkpoint Smart-1 205 Bedienungsanleitung
Checkpoint
Checkpoint Smart-1 225 Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
